Single crystal casting of gas turbine blades using superior ceramic core
Source abstract
Abstract
A ceramic core employed in a single-crystal casting process should endure for a long time at casting temperatures above 1500 °C. Therefore, in this work, an inorganic binder was applied to a conventional injection-molding method to produce a core having enough strength during the casting process. The starting powders for the ceramic core used a mixture of three kinds of fused silica with particle sizes of 117 μm, 33 μm, and 17 μm, zircon flour of 10 μm, and silicon carbide of 16 μm. The mixed ceramic powder was coated with a silica precursor and then dried at 80 °C for 1 h. The dried powder was mixed with wax and injection molded. The injected ceramic core was heat-treated at 1200 and 1500 °C for 1 h,and then reheated at 1550 °C for 3 h. The heat treatment at 1550 °C was conducted to investigate the applicability of the core coated with the inorganic binder in the casting process. The inorganic binder-coated core with a superior firing strength had no cracks or surface defects after the heat treatment, compared with the core without the inorganic binder. In addition, the turbine blade of 150 mm length was well cast as a single crystal and the internal core was completely eluted.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced ceramic materials synthesis · High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. Fabrication of single-crystal superalloy hollow blade based on integral ceramic mold10.1016/j.jmatprotec.2019.04.037 ↗
2. Optimization of molding sand composition for quality improvement of iron castings10.1016/j.clay.2012.07.005 ↗
3. Modeling transient slag-layer phenomena in the shell/mold gap in continuous casting of steel10.1007/s11663-003-0041-x ↗
4. An investigation into stainless-steel/structure-alloy-steel bimetal produced by shell mold casting10.1016/j.matdes.2008.04.074 ↗
5. Dimensional variations of castings and moulds in the ceramic mould casting process mater10.1016/j.jmatprotec.2007.01.030 ↗
6. Development of a high-temperature mold process for sand casting with a thin wall and complex shape10.1016/j.tsf.2016.08.069 ↗
7. A new binder system for preparing high strength inorganic molds in precision casting10.1016/j.matchemphys.2010.11.015 ↗
8. A new in situ process in precision casting for mold fabrication10.1016/j.jeurceramsoc.2011.03.013 ↗
9. Modeling of shrinkage during investment casting of thin-walled hollow turbine blades10.1016/j.jmatprotec.2017.01.005 ↗
10. Callister W.D., 8th Edition. Materials Science and Engineering. Wiley, Florida. pp. 550-551.
11. Physical properties of sodium silicate based silica aerogels prepared by single step sol–gel process dried at ambient pressure10.1016/j.jallcom.2008.09.029 ↗
12. Synthesis of amino-modified ordered mesoporous silica as a new nano sorbent for the removal of chlorophenols from aqueous media10.1016/j.cej.2009.02.023 ↗
13. Mesoporous calcium silicate for controlled release of bovine serum albumin protein10.1016/j.actbio.2009.01.012 ↗
14. Development of a new coating system for the high functional mold in thin-wall casting
15. Sasaki · 2009
16. Barsoum · 1997
17. Ege · 1994
18. Shewmon · 1963
19. Synthesis of SiO2–polyacrylic acid hybrid hydrogel with high mechanical properties and salt tolerance using sodium silicate precursor through sol–gel process10.1016/j.matlet.2008.11.029 ↗
20. Preparation of silicate stalagmite from sodium silicate10.1016/j.jallcom.2008.11.050 ↗