journal article·2022-03Open access

Effect of carbon distribution range in mixed bainite / martensite / retained austenite microstructure on mechanical properties

X.Y. Long, D.Y. Sun, K. Wang, F.C. Zhang, Z.N. Yang, Y.G. Li, C.L. Zheng

Abstract

Carbide-free bainitic steels with the bainitic ferrite (BF) as matrix constituent have been widely used and manufactured. The mixed microstructure of pre-formed martensite (M), BF, and retained austenite (RA) was obtained by quenching for a short time below the martensitic transformation temperature followed by austempering. A similar amount of fresh martensite was obtained by interrupted austempering at the same temperature. Results show that the carbon distribution among these constituents in the mixed microstructure plays a major role in controlling mechanical properties. The carbon content of M and BF in the M-BF-RA microstructure is lower than that of BF-M-RA microstructure, while that of RA was reversed. Mechanical properties of the M-BF-RA microstructure exhibit higher toughness, higher product of strength and elongation as well as higher yield ratio, rather than strength, compared to that of the BF-M-RA microstructure. It can be attributed to toughened pre-formed martensite with low carbon content and mechanical stable RA with high carbon content. In addition, the pre-formed martensite decreases the block size, leading to the increase of high angle grain boundaries, which further improves toughness. The high carbon fresh martensite BF increased the strength of the BF-M-RA microstructure, but sharply decreases ductility and toughness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Omparative micromechanics assessment of high-carbon martensite/bainite bearing steel microstructures using in-situ synchrotron X-ray diffraction10.1016/j.mtla.2020.100948 ↗
2. Design of high-strength and damage-resistant carbide-free fine bainitic steels for railway crossing applications10.1016/j.msea.2019.05.043 ↗
3. Characteristics of carbide-free medium-carbon bainitic steels in high-stress abrasive wear conditions
4. Effect of substitution of Si by Al on the microstructure and mechanical properties of bainitic transformation-induced plasticity steels10.1016/j.jmst.2017.09.002 ↗
5. Development of the low temperature bainite10.1016/j.acme.2016.02.007 ↗
6. Carbon and nitrogen effects on microstructure and kinetics associated with bainitic transformation in a low-alloyed-steel10.1016/j.jallcom.2015.11.007 ↗
7. Acceleration of bainitic transformation by introducing AlN in medium carbon steel10.1080/02670836.2018.1543107 ↗
8. Impact of austenite grain boundaries and ferrite nucleation on bainite formation in steels10.1016/j.actamat.2020.01.065 ↗
9. New insights into the effects of deformation below-MS on isothermal kinetics of bainitic transformation10.1016/j.jmrt.2020.11.039 ↗
10. The combining effects of ausforming and below-Ms or above-Ms austempering on the transformation kinetics microstructure and mechanical properties of lowcarbon bainitic steel10.1016/j.matdes.2019.108123 ↗
11. Effect of pre-existing martensite within the microstructure of nano bainitic steel on its mechanical properties10.1016/j.matchemphys.2020.124160 ↗
12. Evolution of tensile properties with transformation temperature in medium-carbon carbide-free bainitic steel10.1016/j.msea.2020.138964 ↗
13. Inconsistent effects of austempering time within transformation stasis on monotonic and cyclic deformation behaviors of an ultrahigh silicon carbide-free nanobainite steel10.1016/j.msea.2019.01.100 ↗
14. Structure-property relation in a quenched-partitioned low alloy steel involving bainite transformation10.1016/j.msea.2016.05.004 ↗
15. The potential of mechanical twinning in ultrafine retained austenite to enhance high cycle fatigue property of advanced bainitic steels10.1016/j.ijfatigue.2020.105804 ↗
16. Characteristics of bainitic transformation and its effects on the mechanical properties in quenching and partitioning steels10.1016/j.msea.2020.140706 ↗
17. Bhadeshia · 2001
18. Quantitative measurement of deformation-induced martensite in 304 stainless steel by X-ray diffraction10.1016/j.scriptamat.2004.03.011 ↗
19. Application of quenching and partitioning processing to medium Mn steel10.1007/s11661-014-2657-7 ↗
20. The effect of morphology on the stability of retained austenite in a quenched and partitioned steel10.1016/j.scriptamat.2012.11.003 ↗
21. Three-dimensional atom probe analysis of solute distribution in thermomechanically processed TRIP steels10.1016/j.actamat.2006.12.001 ↗
22. A novel thermomechanical approach to produce a fine ferrite and low-temperature bainitic composite microstructure10.1016/j.actamat.2013.08.029 ↗
23. Bainite transformation of low carbon Mn–Si TRIP-assisted multiphase steels: influence of silicon content on cementite precipitation and austenite retention10.1016/S0921-5093(99)00331-7 ↗
24. Complementary use of transmission electron microscopy and atom probe tomography for the examination of plastic accommodation in nanocrystalline bainitic steels10.1016/j.actamat.2011.06.024 ↗
25. Effect of prior athermal martensite on the isothermal transformation kinetics below Ms in a low-C high-Si steel10.1007/s11661-015-3285-6 ↗
26. Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below Ms10.1016/j.actamat.2020.02.003 ↗
27. Effect of two-step austempering process on transformation kinetics of nanostructured bainitic steel10.3390/ma12010166 ↗
28. Effect of martensite pre-quenching on bainite transformation kinetics, martensite/bainite duplex microstructures, mechanical properties and retained austenite stability of GCr15 bearing steel10.1016/j.jmrt.2021.09.070 ↗
29. A review of the thermal stability of metastable austenite in steels:Martensite formation10.1016/j.jmst.2021.03.020 ↗
30. Refined bainite microstructure and mechanical properties of a high-strength low-carbon bainitic steel treated by austempering below and above MS steel
31. An advanced approach to reconstructing parent orientation maps in the case of approximate orientation relations: application to steels10.1016/j.actamat.2012.04.034 ↗
32. Accelerating nano-bainite transformation based on a new constructed microstructural predicting model10.1016/j.msea.2019.01.061 ↗
33. Improvement of strength-toughness combination in austempered low carbon bainitic steel: the key role of refining prior austenite grain size10.1016/j.jallcom.2017.03.024 ↗
34. Influence of the prior athermal martensite on the mechanical response of advanced bainitic steel10.1016/j.msea.2018.08.047 ↗
35. Decomposition characteristic of austenite retained in GCr15 bearing steel modified by addition of 1.3wt.% silicon during tempering10.1016/j.jmrt.2017.08.012 ↗
36. Bainite growth retardation due to mechanical stabilisation of austenite10.1016/j.mtla.2019.100384 ↗
37. Tailoring strength/ductility combination in 2.5 wt% Si-alloyed middle carbon steel produced by the two-step Q-P treatment with a prolonged partitioning stage10.1016/j.msea.2020.139721 ↗
38. Roles of pre-formed martensite in below-Ms bainite formation, microstructure, strain partitioning and impact absorption energies of low-carbon bainitic steel10.1016/j.jmst.2021.05.002 ↗
39. Effect of martensite pre-quenching on bainite transformation kinetics, martensite/bainite duplex microstructures, mechanical properties and retained austenite stability of GCr15 bearing steel10.1016/j.jmrt.2021.09.070 ↗
40. Formation of bainite below the MS temperature: kinetics and crystallography10.1016/j.actamat.2015.12.027 ↗
41. Austenite stability and mechanical properties of a low-alloyed ECAPed TRIP-aided steel10.1016/j.msea.2018.03.085 ↗
42. Enhanced ductility and toughness in an ultrahigh-strength Mn–Si–Cr–C steel: the great potential of ultrafine filmy retained austenite10.1016/j.actamat.2014.05.055 ↗
43. Designing low carbon, low temperature bainite10.1179/174328408X275982 ↗
44. Effect of transformation substructure on the strength and toughness of Fe-Mn alloys10.1007/BF03037855 ↗
45. Krauss · 2005
46. Effect of austenite grain size on the morphology and crystallography of lath martensite in low carbon steels10.2355/isijinternational.45.91 ↗
47. Influence of refined hierarchical martensitic microstructures on yield strength and impact toughness of ultra-high strength stainless steel10.1016/j.jmst.2020.04.001 ↗
48. Analysis of different acicular ferrite microstructures in low-carbon steels by electron backscattered diffraction. Study of their toughness behavior10.1007/s11661-003-0010-7 ↗
49. Rolling contact fatigue of bainitic rail steels: the significance of microstructure10.1016/j.msea.2016.01.052 ↗
50. Role of bainitic microstructures with M-A constituent on the toughness of an HSLA steel for seismic resistant structural applications10.1016/j.msea.2020.140390 ↗
51. Loading-rate dependence of fracture absorption energy of low-carbon carbide-free bainitic steel10.1016/j.jallcom.2015.06.215 ↗
52. Complex unloading behaviour: nature of the deformation and its consistent representation10.1016/j.ijplas.2010.12.003 ↗
53. Variation and consistency of Young's modulus in steel10.1016/j.jmatprotec.2015.08.024 ↗