journal article·2022-09Open access

Effect of pulse mode and frequency on microstructure and properties of 2219 aluminum alloy by ultrahigh-frequency pulse Metal-Inert Gas Welding

Xiaocong Kuang, Bojin Qi, Hao Zheng

Abstract

Based on self-developed ultra high frequency pulse Metal-Inert Gas Welding (UFP-MIG) power source, the ultra-high frequency pulse (UFP) current was studied as an effective way for improving the microstructure and properties of 2219 aluminum alloy joints. The welding pores reduction performance, microstructures, microhardness, and tensile properties of conventional pulsed MIG(CP-MIG) welds and the UFP-MIG welds with different modes and frequencies were investigated. The results indicated that the UFP-MIG process could almost completely eliminate welding porosity in the joints of 2219 aluminum alloy. Compared with CP-MIG welding process, the grain size of the UFP-MIG welding zone was reduced and gradually decreased as the frequency of UFP increased. Similarly, the grain refinement effect also appeared in the heat affected zone (HAZ) near the welds, and the grain size could be reduced by up to 14.85%. Meanwhile, the morphology and uniformity of θ phases and α+θ eutectics along grain boundaries of UFP-MIG welds were also improved. The microhardness in the weld zone and partially melted zone (PMZ) of UFP-MIG weld joints with different modes and frequencies were significantly improved. The highest joint average microhardness occurred at peak pulse mode (PP) with 40 kHz(75.17HV), which was 27.9% higher than that of CP-MIG (58.74HV). The strength and ductility of welded joints were simultaneously improved by UFP-MIG weld process. Fracture analysis results showed that the large reduction of weld pores, the refinement of weld grains, and the lower segregation of Cu element in the eutectic were responsible for the joint tensile properties improvement.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Influences of pulsed current tungsten inert gas welding parameters on the tensile properties of AA 6061 aluminium alloy10.1016/j.matdes.2006.05.027 ↗
2. Study of arc ultrasonic excitation and its characteristics
3. The ultrasonic characteristics of high frequency modulated arc and its application in material processing10.1016/j.ultras.2014.06.003 ↗
4. Ultrasonic generation by exciting electric arc: a tool for grain refinement in welding process10.1063/1.2357857 ↗
5. Microstructure and porosity analysis in ultrasonic assisted TIG welding of 2014 aluminum alloy
6. Research on short circuiting transfer mode of ultrasonic assisted GMAW method10.1179/1362171811Y.0000000058 ↗
7. The effect of high-frequency pulsing of a welding arc10.1109/TIA.1985.349557 ↗
8. Development of high frequency tungsten inert gas welding method10.1016/j.matdes.2012.07.054 ↗
9. Reduction of ductility-dip cracking susceptibility by ultrasonic-assisted GTAW10.1016/j.jmatprotec.2016.08.018 ↗
10. Reduction of Laves phase in nickel-alloy welding process under ultrasonic Ampère’s force10.1016/j.jmatprotec.2017.10.007 ↗
11. High-frequency pulse-modulated square wave AC TIG welding of AA6061-T6 aluminum alloy10.1007/s40194-020-00953-9 ↗
12. A novel ultrafast-convert complex-pulse variable-polarity arc welding power topology
13. Analysis on characteristic of ultra high frequency pulsed gas tungsten arc welding process10.3901/JME.2016.02.026 ↗
14. The effect of arc behavior on weld geometry by high-frequency pulse GTAW process with 0Cr18Ni9Ti stainless steel10.1007/s00170-012-4438-z ↗
15. Influences of ultrasonic pulse square-wave current parameters on microstructures and mechanical properties of 2219 aluminum alloy weld joints
16. Segregation in fusion weld of 2219 aluminum alloy and its influence on mechanical properties of weld10.1016/S1003-6326(17)60030-X ↗
17. Keyhole welding of AA2219 aluminum alloy with double-pulsed variable polarity gas tungsten arc welding10.1016/j.jmapro.2018.06.006 ↗
18. Process characteristics and properties of AA2219 aluminum alloy welded by double pulsed VPTIG welding10.1016/j.jmatprotec.2018.11.015 ↗
19. Microstructure, tensile properties of Ti-6Al-4V by ultra high pulse frequency GTAW with low duty cycle10.1016/j.jmatprotec.2014.08.026 ↗
20. Effect of arc behavior on Ti-6Al-4V welds during high frequency pulsed arc welding10.1016/j.jmatprotec.2016.12.003 ↗
21. Pulsed arc light monitoring and temperature reconstruction with arc welding10.1080/13621718.2020.1758400 ↗
22. Design of hybrid ultrasonic frequency pulsed GMAW power source
23. Ando · 1985 · p.249
24. How ultra high frequency of pulsed gas tungsten arc welding affects weld porosity of Ti-6Al-4V alloy10.1007/s00170-014-6324-3 ↗
25. The temperature dependence of the viscosity of liquid metals10.13182/NSE62-A28099 ↗
26. High-frequency pulse modulated variable polarity welding power and its arc pressure
27. Effect of fluid in molten pool on the welds with Ti-6Al-4V during pulsed arc welding10.1007/s00170-015-7272-2 ↗
28. Characterization of the evolution of 2219-T87 aluminum as a function of the friction stir welding process
29. Steady state columnar and equiaxed growth of dendrites and eutectic10.1016/0025-5416(84)90201-5 ↗
30. Russell · 2005
31. Effect of pulse frequency on microstructure and properties of Ti-6Al-4V by ultrahigh-frequency pulse gas tungsten arc welding10.1007/s00170-013-4822-3 ↗
32. Microstructural evolution and its effect on mechanical properties in different regions of 2219-C10S aluminum alloy TIG-welded joint-ScienceDirect10.1016/S1003-6326(20)65407-3 ↗