The role of initial grain size on bimodal-grained microstructure and mechanical properties of an extruded Mg-Gd-Y-Nd-Zr alloy
Source abstract
Abstract
Influence of initial grain size on the formation of bimodal-grained microstructure and mechanical properties of a Mg-11Gd-3Y-0.5Nd–Zr alloy was investigated. The results indicate that the fraction of unrecrystallized (un-DRXed) grains in bimodal-grained microstructure was governed by the initial grain size, and the fraction increases with the increasing of initial grain size. Formation of un-DRXed grains in samples with a small initial grain size is induced by the uneven distribution of grain size, in which coarser grains is more difficult to recrystallize. However, the recrystallization behavior in samples with large initial grain size is mainly affected by the difference in orientation among grains, and grains with orientation that are not favored for slip are difficult to recrystallize. The strength increases while the elongation decreases with the increasing of initial grain size. The sample with the highest initial grain size (178 μm) accordingly shows the best ultimate tensile strength of 459 MPa. The higher strength is mainly due to the higher texture strengthening and hetero-deformation induced (HDI) strengthening provided by higher fraction of un-DRXed grains.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Unveiling the underlying mechanism of forming edge cracks upon high strain-rate rolling of magnesium alloy10.1016/j.jmst.2020.03.006 ↗
2. Research advances in magnesium and magnesium alloys worldwide in 202010.1016/j.jma.2021.04.001 ↗
3. Unveiling the mechanical response and accommodation mechanism of pre-rolled AZ31 magnesium alloy under high-speed impact loading10.1016/j.jma.2021.07.030 ↗
4. Effect of carbonate additive on the microstructure and corrosion resistance of plasma electrolytic oxidation coating on Mg-9Li-3Al alloy10.1007/s12613-021-2377-0 ↗
5. Recent developments in high-strength Mg-RE-based alloys: focusing on Mg-Gd and Mg-Y systems10.1016/j.jma.2018.08.001 ↗
6. The microstructure and corrosion resistance of as-extruded Mg-6Gd-2Y- (0–1.5) Nd-0.2Zr alloys10.1016/j.matdes.2019.108289 ↗
7. Recent developments and applications on high-performance cast magnesium rare-earth alloys10.1016/j.jma.2020.06.021 ↗
8. Dynamic compression behavior of a Mg-Gd-Based alloy at elevated temperature10.1007/s12540-019-00558-y ↗
9. Microstructure and Gd-rich phase evolution of as-cast AZ31-xGd magnesium alloys during semi-solid isothermal heat treatment10.1007/s11771-020-4504-x ↗
10. Corrosion behavior of Mg−Li alloys: a review10.1016/S1003-6326(21)65728-X ↗
11. Microstructure and super high strength of cast Mg-8.5Gd-2.3Y-1.8Ag-0.4Zr alloy10.1016/j.msea.2010.09.004 ↗
12. Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy10.1016/j.jallcom.2014.07.028 ↗
13. Ultrastrong Mg alloy via nano-spaced stacking faults10.1080/21663831.2013.765927 ↗
14. Bulk nanocrystalline high-strength magnesium alloys prepared via rotary swaging10.1016/j.actamat.2020.09.024 ↗
15. Bimodal microstructure - a feasible strategy for high-strength and ductile metallic materials10.1016/j.jmst.2017.11.018 ↗
16. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗
17. Effect of extrusion parameters on microstructure, texture and mechanical properties of Mg-1.38Zn-0.17Y-0.12Ca (at. %) alloy10.1016/j.matchar.2019.03.004 ↗
18. Effects of extrusion speed on the formation of bimodal-grained structure and mechanical properties of a Mg-Gd-based alloy10.1016/j.matchar.2022.111952 ↗
19. The role of bimodal-grained structure in strengthening tensile strength and decreasing yield asymmetry of Mg-Gd-Zn-Zr alloys10.1016/j.msea.2017.09.125 ↗
20. Effect of extrusion parameters on microstructure and mechanical properties of Mg-7.5Gd-2.5Y-3.5Zn-0.9Ca-0.4Zr (wt%) alloy10.1016/j.msea.2016.12.121 ↗
21. Achieving exceptionally high strength in binary Mg-13Gd alloy by strong texture and substantial precipitates10.1016/j.scriptamat.2020.10.052 ↗
22. Ultra high-strength Mg-Gd-Y-Zn-Zr alloy sheets processed by large-strain hot rolling and ageing10.1016/j.msea.2012.03.087 ↗
23. Effects of thermomechanical processing on the microstructure, texture and mechanical properties of a Mg-Gd-based alloy10.1016/j.msea.2019.05.010 ↗
24. Activation of slip and enhanced ductility in as-extruded Mg-Gd-Y-Nd alloys through Si addition10.1016/j.msea.2021.140736 ↗
25. Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles10.1016/j.jma.2021.01.008 ↗
26. Principles of grain refinement in magnesium alloys processed by equal-channel angular pressing10.1007/s10853-009-3725-z ↗
27. Grain refinement and mechanical behavior of a magnesium alloy processed by ECAP10.1007/s10853-010-4589-y ↗
28. Influence of extrusion conditions on microstructure and mechanical properties of Mg-2Gd-0.3Zr magnesium alloy10.1016/j.jma.2020.06.019 ↗
29. Effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy10.3390/met8100790 ↗
30. Effect of deformation conditions on dynamic mechanical behavior of a Mg–Gd-based alloy10.1007/s11665-020-05274-y ↗
31. An unusual extrusion texture in Mg-Gd-Y-Zr alloys10.1002/adem.201500516 ↗
32. A model of continuous dynamic recrystallization10.1016/S1359-6454(03)00078-8 ↗
33. Strain induced dynamic recrystallization nucleation of ZA21 magnesium alloy during compression process at low and medium temperatures10.1016/j.jmrt.2019.10.063 ↗
34. Effect of extrusion ratio and temperature on microstructures and tensile properties of extruded Mg-Gd-Y-Mn-Sc alloy10.1016/j.msea.2020.140330 ↗
35. Grain refinement and weak-textured structures based on the dynamic recrystallization of Mg-9.80Gd-3.78Y-1.12Sm-0.48Zr alloy10.1016/j.jma.2020.06.001 ↗
36. Effect of large thickness-reduction on microstructure evolution and tensile properties of Mg-9Al-1Zn alloy processed by hard-plate rolling10.1016/j.jmst.2021.01.050 ↗
37. Hot deformation behavior of a differential pressure casting Mg-8Gd-4Y-Nd-Zr alloy10.1007/s11665-016-2422-8 ↗
38. The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys10.1016/S1359-6454(03)00005-3 ↗
39. Effects of thermal treatment on microstructure and mechanical properties of a Mg-Gd-based alloy plate10.1016/j.msea.2016.02.032 ↗
40. Synergistically improved damping, elastic modulus and mechanical properties of rolled Mg-8Li-4Y–2Er-2Zn-0.6Zr alloy with twins and long-period stacking ordered phase10.1016/j.jallcom.2021.160663 ↗
41. Annealing coordinates the deformation of shear band to improve the microstructure difference and simultaneously promote the strength-plasticity of composite plate10.1016/j.matdes.2022.110696 ↗
42. Individual effect of recrystallisation nucleation sites on texture weakening in a magnesium alloy: Part 1- double twins10.1016/j.actamat.2017.06.015 ↗
43. Influence of texture on Hall–Petch relationships in an Mg alloy10.1016/j.actamat.2014.08.023 ↗
44. Microstructures and strengthening mechanisms of Mg-8.2Gd-4.6Y-1.5Zn-0.4Zr alloy containing LPSO, β′ and γ type phases10.1016/j.jre.2020.05.012 ↗
45. Microstructures and mechanical properties of a hot-extruded Mg-8Gd-3Yb-1.2Zn-0.5Zr (wt%) alloy10.1016/j.jallcom.2018.10.322 ↗
46. Microstructures and mechanical properties of a Mg-9Gd-3Y-0.6Zn-0.4Zr (wt.%) alloy modified by Y-rich misch metal10.1016/j.msea.2020.140609 ↗
47. Strengthening mechanisms of Mg-Si alloys10.1016/1359-6454(96)00072-9 ↗
48. Precipitation process and effect on mechanical properties of Mg–9Gd–3Y–0.6Zn–0.5Zr alloy10.1016/j.msea.2006.11.047 ↗
49. Exploration of trade-off between elastic modulus and strength of Mg–Gd–Y–Nd–Zr alloy by regulating intermetallic phases through Si addition10.1007/s12540-020-00749-y ↗
50. Rokhlin · 2003
51. Ultrahigh strength as-extruded Mg–10.3Zn–6.4Y–0.4Zr–0.5Ca alloy containing W phase10.1016/j.matdes.2016.06.116 ↗
52. Microstructures and mechanical properties of a high-strength Mg-3.5Sm-0.6Zn-0.5Zr alloy10.1016/j.msea.2017.07.058 ↗
53. Improving age hardening response and mechanical properties of a new Mg-RE alloy via simple pre-cold rolling10.1016/j.jallcom.2018.11.082 ↗
54. Strain hardening behaviour and the Taylor factor of pure magnesium10.1080/14786430801968611 ↗
55. Modeling the precipitation processes and strengthening mechanisms in a Mg-Al-(Zn) AZ91 alloy10.1007/s11661-005-0330-x ↗
56. Phase transformation in Mg-8Gd-4Y-Nd-Zr alloy10.1016/j.jallcom.2011.03.059 ↗
57. Effect of secondary extrusion on the microstructure and mechanical properties of a Mg–RE alloy10.1016/j.msea.2014.08.022 ↗
58. Trace element effects on precipitation processes and mechanical properties in an Al-Cu-Li alloy10.1007/s11661-997-0203-6 ↗
59. Heterogeneous lamella structure unites ultrafine-grain strength with coarse-grain ductility10.1073/pnas.1517193112 ↗
60. Heterogeneous materials: a new class of materials with unprecedented mechanical properties10.1080/21663831.2017.1343208 ↗
61. Distribution characteristics of in-grain misorientation axes in cold-rolled commercially pure Titanium and their correlation with active slip modes10.1007/s11661-010-0410-4 ↗
62. Investigation of prism ⟨a⟩ slip in warm-rolled AZ31 alloy10.1007/s11661-011-0800-2 ↗