journal article·2024-01Open access

Preparation, mechanical properties and wear resistance of dual-sized TiC particles reinforced high-entropy alloy cermet coating

Meng Xiao, Shunfeng Nai, Shuai Nan, Chuangshi Feng, Zhou Guan, Chao Huo, Fuxiang Zhang, Zhaoguo Qiu, Gong Li

Abstract

The replacement of WC-Co cermet coating partially or entirely has evolved as one of the most promising research hotspots in terms of coating properties as well as economic reasons. In this study, the TiC reinforced AlCoCrFeNi high entropy alloy (HEA) composite coating based on new sintering method was explored. Firstly, the combination of spray drying and plasma spheroidization is proposed to fabricate TiC/HEA composite powder for thermal spraying application. After that, the corresponding composite coating was deposited by high velocity air-fuel (HVAF) process. The results show that the developed TiC/HEA powder has a more compact structure and higher sphericity, which helps to improve powder fluidity, meanwhile, with 50 wt% TiC incorporation, the porosity、hardness、bonding strength and fracture toughness of TiC/HEA composite coating are 0.8 % 765.2 HV0.3, 68.1 Mpa and 2.7 MPa m−1/2, respectively, showing simultaneous hardening, densifying and toughening effects after introducing dual-sized TiC particles. Besides, the good wear performances of TiC/HEA composite coating including low wear rate (4.2 × 10−5 mm3 N−1 m−1) and coefficient of friction (0.34) are obtained,indicating a valuable application prospect. In addition, the wear mechanisms of TiC/HEA composite coating are determined by abrasive and oxidation wears and that of grinding ball is abrasive wear and adhesive wears.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · High Entropy Alloys Studies · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. Comparison of tribological properties of HVOF sprayed coatings with different composition10.1016/j.surfcoat.2017.02.021 ↗
2. Tribological properties of HVOF-sprayed WC-Co coatings deposited from Ni-plated powders at elevated temperature10.1016/j.surfcoat.2017.08.026 ↗
3. Corrosion behavior of WC-η coatings in molten zinc10.1016/j.corsci.2022.110192 ↗
4. Sliding wear of conventional and suspension sprayed Nanocomposite WC-Co coatings: an Invited review10.1007/s11666-021-01185-z ↗
5. Studies on the properties of high-velocity oxy-fuel thermal spray coatings for higher temperature applications10.1007/s11003-006-0047-z ↗
6. Wear behaviour of WC–Co HVOF coatings at different temperatures in air and argon10.1016/j.wear.2015.01.035 ↗
7. Abrasion, erosion and scuffing resistance of carbide and oxide ceramic thermal sprayed coatings for different applications10.1016/0043-1648(93)90538-W ↗
8. Microstructure and properties of HVOF-sprayed chromium alloyed WC–Co and WC–Ni coatings10.1016/j.surfcoat.2008.04.019 ↗
9. Micromechanical properties and sliding wear behaviour of HVOF-sprayed Fe-based alloy coatings10.1016/j.wear.2011.12.001 ↗
10. Alternative metallic matrices for WC-based HVOF coatings10.1016/j.surfcoat.2020.126308 ↗
11. Development, characterization, and cavitation erosion analysis of high velocity oxy-fuel (HVOF) sprayed TiC and (70Cu-30Ni)-Cr based composite coatings on SS316 steel10.1016/j.triboint.2023.108621 ↗
12. High-temperature tribological behavior of CoCrFeNiV high-entropy alloys: a parallel comparison with CoCrFeNiMn high-entropy alloys10.1016/j.triboint.2022.107736 ↗
13. Strengthening the CoCrFeNiNb0.25 high entropy alloy by FCC precipitate10.1016/j.jallcom.2016.01.153 ↗
14. Tribological behavior of microwave synthesized high entropy alloy claddings
15. Effect of high Fe content on the microstructure, mechanical and corrosion properties of AlCoCrFeNi high-entropy alloy coatings prepared by gas tungsten arc cladding10.1016/j.surfcoat.2021.127242 ↗
16. Microwave synthesized complex concentrated alloy coatings: Plausible solution to cavitation induced erosion-corrosion10.1016/j.ultsonch.2018.09.004 ↗
17. Mechanism of the high temperature oxidation of titanium carbide10.1515/HTMP.1997.16.4.243 ↗
18. Microstructure and wear resistance of a laser clad TiC reinforced nickel aluminides matrix composite coating10.1016/j.msea.2003.09.104 ↗
19. Effects of TiC on the microstructure and properties of TiC/TiAl composite coating prepared by laser cladding10.1016/j.optlastec.2018.11.037 ↗
20. Corrosion and wear performances of alternative TiC-based thermal spray coatings10.1016/j.surfcoat.2022.128400 ↗
21. Preparation, mechanical properties and enhanced wear resistance of TiC-Fe composite cermet coating10.1016/j.ijrmhm.2021.105672 ↗
22. Cobalt free metallic binders for HVOF thermal sprayed wear resistant coatings10.1016/j.surfcoat.2023.129243 ↗
23. 1.03 - microstructure and morphology of Hardmetals
24. Cycle oxidation behavior of nanostructured Ni60–TiB2 composite coating sprayed by HVOF technique10.1016/j.apsusc.2011.07.026 ↗
25. Preparation and enhanced wear resistance of HVAF-sprayed Fe-TiB2 cermet coating reinforced by carbon nanotubes10.1016/j.surfcoat.2021.126860 ↗
26. Tribological behavior of WC-Co HVAF-sprayed composite coatings modified by nano-sized TiC addition, 8th Rencontres
27. Preparation, mechanical properties and cyclic oxidation behavior of the nanostructured NiCrCoAlY-TiB2 coating10.1016/j.ceramint.2018.07.165 ↗
28. Microstructure and sliding wear behavior of nanostructured Ni60–TiB2 composite coating sprayed by HVOF technique10.1016/j.surfcoat.2011.07.096 ↗
29. Designing enhanced spray dried particles for inhalation: a review of the impact of excipients and processing parameters on particle properties10.1016/j.powtec.2021.02.031 ↗
30. Effects of process parameters on morphologies of titanium carbide powder by thermal plasma treatment10.1088/2053-1591/ab5ddb ↗
31. Microstructure and corrosion behavior of HVAF-sprayed Fe-based composite coatings doped TiB2 and CNTs10.1016/j.corsci.2022.110629 ↗
32. Effect of microstructure (particulate size and volume fraction) and counterface material on the sliding wear resistance of particulate-reinforced aluminum matrix composites10.1007/BF02652272 ↗
33. Effect of microstructure (particulate size and volume fraction) and counterface material on the sliding wear resistance of particulate-reinforced aluminum matrix composites10.1007/BF02652272 ↗
34. Simultaneously enhancing wear and corrosion resistance of HVAF-sprayed Fe-based amorphous coating from Mo clad feedstock10.1016/j.jmatprotec.2021.117465 ↗
35. Development and implementation of plasma sprayed nanostructured ceramic coatings10.1016/S0257-8972(01)01470-0 ↗
36. Amorphous zones in flame sprayed alumina–titania–zirconia compounds10.1016/j.ceramint.2010.09.020 ↗
37. A review on ICP powder plasma spheroidization process parameters10.1016/j.ijrmhm.2021.105764 ↗
38. Suppression of crystallization during high velocity impact quenching of alumina droplets: observations and characterization10.1016/j.msea.2006.11.132 ↗
39. Microstructure and properties of AlCrFeNiMoNb high-entropy alloys coating on ZM5 magnesium alloy prepared by high-velocity air fuel (HVAF) spray10.1016/j.jmrt.2023.09.125 ↗
40. Effects of normal load and velocity on the dry sliding tribological behaviour of CoCrFeNiMo0.2 high entropy alloy10.1016/j.triboint.2019.106116 ↗
41. Sliding and abrasive wear resistance of thermal-sprayed WC-CO coatings10.1361/105996301770349583 ↗