journal article·2022-09Open access

Effect of magnesium salt contamination on the microstructures and properties of metakaolinite-based geopolymer: the role of MgCl2 and MgSO4

Baifa Zhang, Dongchao Huang, Lijuan Li, Min Lin, Yong Liu, Wei Fang, Junjie Lu, Feng Liu, Yun Li, Yi Liu, Zhe Xiong

Abstract

Ion contamination considerably influences the properties of geopolymers. This study investigated the effects of magnesium chloride (MgCl2) and magnesium sulfate (MgSO4) concentrations on the microstructure and properties of metakaolinite-based geopolymers with Si/Al ratios of 1.3 (adding NaOH) and 1.6 (adding NaOH and Na2SiO3). The chemical structures and compositions of as-obtained geopolymers formed through the alkali activation of kaolinite were characterized through X-ray diffraction, Fourier-transform infrared spectroscopy, and nuclear magnetic resonance (NMR) spectroscopy, while the microstructure was characterised via scanning electron microscopy and mercury intrusion porosimetry. The salt-free geopolymer with a Si/Al ratio of 1.3 exhibited a loose microstructure and hence poor 28-day compressive strength (9.4 MPa). The addition of magnesium salt to the geopolymer did not considerably influence its microstructure and mechanical properties. Comparatively, the geopolymer with a Si/Al ratio of 1.6 exhibited a compact microstructure and high 28-day compressive strength (43.0 MPa). The geopolymer compressive strength gradually decreased with increasing salt concentration. MgCl2 addition induced halite formation, increased pore diameter and pore volume, and reduced Si incorporated into the geopolymer matrix. In contrast, MgSO4 addition resulted in relatively less change in the pore diameter and pore volume and based on NMR result, more Si was incorporated into the geopolymer matrix. Thus, MgCl2 was more detrimental to the mechanical properties of the kaolinite-based geopolymers than MgSO4. Overall, the results indicate that salt contamination considerably affects the chemical compositions, microstructural characteristics, and compressive strength of metakaolinite-based geopolymers at high Si/Al ratio (adding NaOH and Na2SiO3) and those chlorine ions are more detrimental to the properties of metakaolinite-based geopolymer than sulfate ions.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Magnesium Oxide Properties and Applications · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (66)

Show source-provided references
1. Environmental impacts and decarbonization strategies in the cement and concrete industries10.1038/s43017-020-0093-3 ↗
2. A comprehensive overview about the influence of different admixtures and additives on the properties of alkali-activated fly ash10.1016/j.matdes.2013.07.074 ↗
3. Effect of curing conditions on the microstructure and mechanical performance of geopolymers derived from nanosized tubular halloysite10.1016/j.conbuildmat.2020.121186 ↗
4. Solidification/stabilization of municipal solid waste incineration fly ash using uncalcined coal gangue–based alkali-activated cementitious materials10.1007/s11356-019-05832-5 ↗
5. Microstructure and mechanical properties of metakaolin-based geopolymer composites containing high volume of spodumene tailings10.1016/j.clay.2022.106412 ↗
6. Rubberized geopolymer concrete: dependence of mechanical properties and freeze-thaw resistance on replacement ratio of crumb rubber10.1016/j.conbuildmat.2021.125248 ↗
7. Modeling dissolution-precipitation kinetics of alkali-activated metakaolin10.1021/acsomega.8b02380 ↗
8. Effects of kinds of alkali-activated ions on geopolymerization process of geopolymer cement pastes10.1016/j.conbuildmat.2021.123536 ↗
9. Geopolymerization of halloysite via alkali-activation: dependence of microstructures on precalcination10.1016/j.clay.2019.105375 ↗
10. A review: the comparison between alkali-activated slag (Si+Ca) and metakaolin (Si+Al) cements10.1016/j.cemconres.2010.03.020 ↗
11. Effects of seawater on mechanical properties, mineralogy and microstructure of calcium silicate slag-based alkali-activated materials10.1016/j.conbuildmat.2019.03.288 ↗
12. Effect of NaOH content on hydration, mineralogy, porosity and strength in alkali/sulfate-activated binders from ground granulated blast furnace slag and phosphogypsum10.1016/j.cemconres.2020.106054 ↗
13. Utilization of calcium carbide residue as solid alkali for preparing fly ash-based geopolymers: dependence of compressive strength and microstructure on calcium carbide residue, water content and curing temperature10.3390/ma15030973 ↗
14. Advances in alkali-activation of clay minerals10.1016/j.cemconres.2020.106050 ↗
15. Durability performance of fly ash-based geopolymer concrete buried in saline environment for 10 years10.1016/j.conbuildmat.2021.122596 ↗
16. A critical review of geopolymer properties for structural fire-resistance applications10.1016/j.conbuildmat.2019.06.076 ↗
17. High strength metakaolin/epoxy hybrid geopolymers: synthesis, characterization and mechanical properties10.1016/j.clay.2022.106459 ↗
18. Greenhouse gas emissions of different fly ash based geopolymer concretes in building construction10.1016/j.jclepro.2018.08.311 ↗
19. A comprehensive assessment of the global warming potential of geopolymer concrete10.1016/j.jclepro.2021.126669 ↗
20. Geopolymer concrete: a review of some recent developments10.1016/j.conbuildmat.2015.03.036 ↗
21. Fatigue bond behaviour between basalt fibre-reinforced polymer bars and seawater sea-sand concrete10.1016/j.ocecoaman.2022.106038 ↗
22. Assessment of water consumption during production of material and construction phases of residential building projects10.1016/j.scs.2019.101785 ↗
23. Nanni. Compressive strength development of seawater-mixed concrete subject to different curing regimes
24. Axial performance of seawater sea-sand concrete columns reinforced with basalt fibre-reinforced polymer bars under concentric compressive load
25. Study on fracture properties of alkali-activated slag seawater coral aggregate concrete10.1016/j.conbuildmat.2019.06.191 ↗
26. A study on the effect of the salt content on the solidification of sulfate saline soil solidified with an alkali-activated geopolymer10.1016/j.conbuildmat.2018.05.013 ↗
27. Sulfate-bearing clay and Pietra Serena sludge: raw materials for the development of alkali activated binders10.1016/j.conbuildmat.2021.124030 ↗
28. A Preliminary study on the use of magnetic, Zamzam, and sea water as mixing water for alkali-activated slag pastes10.1016/j.conbuildmat.2019.02.162 ↗
29. Effect of sodium sulfate on strength and microstructure of alkali-activated fly ash based geopolymer10.1007/s11771-020-4400-4 ↗
30. Effects of natural seawater mixing on the properties of alkali-activated slag binders10.1016/j.conbuildmat.2021.123601 ↗
31. Characterization of the mechanical properties of eco-friendly concrete made with untreated sea sand and seawater based on statistical analysis10.1016/j.conbuildmat.2019.117339 ↗
32. Multiscale investigations on hydration mechanisms in seawater OPC paste10.1016/j.conbuildmat.2018.10.010 ↗
33. 30 years of successes and failures in geopolymer applications
34. The strength and microstructure of two geopolymers derived from metakaolin and red mud-fly ash admixture: a comparative study10.1016/j.conbuildmat.2011.12.011 ↗
35. Thermoelectric behaviors of fly ash and metakaolin based geopolymer10.1016/j.conbuildmat.2019.117757 ↗
36. Structural and mechanical properties of geopolymers made of aluminosilicate powder with different SiO2/Al2O3 ratio: molecular dynamics simulation and microstructural experimental study10.1016/j.conbuildmat.2019.117935 ↗
37. Atomistic simulations of geopolymer models: the impact of disorder on structure and mechanics10.1021/acsami.8b03873 ↗
38. Reexamining calcination of kaolinite for the synthesis of metakaolin geopolymers - roles of dehydroxylation and recrystallization10.1016/j.jnoncrysol.2017.01.024 ↗
39. Microstructural and mechanical properties of poly(sialate-siloxo) networks obtained using metakaolins from kaolin and halloysite as aluminosilicate sources: a comparative study10.1016/j.clay.2020.105448 ↗
40. Reaction mechanisms of calcined kaolin processing waste-based geopolymers in the presence of low alkali activator solution10.1016/j.conbuildmat.2019.06.116 ↗
41. Formation of zeolites in metakaolin-based geopolymers and their potential application for Cs immobilization
42. Effect of blast-furnace slag on physicochemical properties of pozzolan-based geopolymers10.1016/j.matchemphys.2020.123880 ↗
43. Chloride ion binding effect and corrosion resistance of geopolymer materials prepared with seawater and coral sand10.1016/j.conbuildmat.2021.125126 ↗
44. The durability of alkali-activated materials in comparison with ordinary Portland cements and concretes: a review
45. The effects of inorganic salt contamination on the strength and durability of geopolymers10.1016/S0927-7757(02)00239-X ↗
46. Impact of sulfate and nitrate incorporation on potassium- and sodium-based geopolymers: geopolymerization and materials properties10.1007/s10853-011-5516-6 ↗
47. ASTM C191-21 standard test methods for time of setting of hydraulic cement by Vicat needle.
48. New selective dissolution process to quantify reaction extent and product stability in metakaolin-based geopolymers10.1016/j.compositesb.2019.107172 ↗
49. Do geopolymers actually contain nanocrystalline zeolites? A reexamination of existing results10.1021/cm050230i ↗
50. Kaolin-based geopolymers: effect of mechanical activation and curing process10.1016/j.conbuildmat.2012.12.069 ↗
51. Relations between the structural characteristics and compressive strength in metakaolin based geopolymers with different molar Si/Al ratios10.1016/j.ceramint.2015.04.125 ↗
52. Metal powders as foaming agents in fly ash based geopolymer synthesis and their impact on the structure depending on the Na/Al ratio10.1016/j.cemconcomp.2018.02.009 ↗
53. Changes in structure, morphology, porosity, and surface activity of mesoporous halloysite nanotubes under heating10.1346/CCMN.2012.0600602 ↗
54. Solidification/stabilization mechanism of Pb(II), Cd(II), Mn(II) and Cr(III) in fly ash based geopolymers10.1016/j.conbuildmat.2017.12.006 ↗
55. Use of infrared spectroscopy to study geopolymerization of heterogeneous amorphous aluminosificates10.1021/la026127e ↗
56. One-Part Geopolymer mixes from geothermal silica and sodium aluminate10.1021/ie8006825 ↗
57. Influence of the Si/Al ratio in geopolymers on the stability against acidic attack and the immobilization of Pb2+ and Zn2+10.1016/j.conbuildmat.2019.08.015 ↗
58. Quantitative kinetic and structural analysis of geopolymers. Part 1. The activation of metakaolin with sodium hydroxide10.1016/j.tca.2012.03.021 ↗
59. Quantitative kinetic and structural analysis of geopolymers. Part 2. Thermodynamics of sodium silicate activation of metakaolin10.1016/j.tca.2013.01.040 ↗
60. The effect of alkali ions on the incorporation of aluminum in the calcium silicate hydrate (C–S–H) phase resulting from Portland cement hydration studied by 29Si MAS NMR10.1111/jace.12024 ↗
61. Solid-state nuclear magnetic resonance spectroscopy of cements
62. Effects of Si/Al ratio on the structure and properties of metakaolin based geopolymer10.1016/j.ceramint.2016.06.033 ↗
63. Geopolymerization reaction, microstructure and simulation of metakaolin-based geopolymers at extended Si/Al ratios
64. Pore size dependent connectivity and ionic transport in saturated cementitious materials10.1016/j.conbuildmat.2019.117680 ↗
65. Effect of fly ash characteristics on delayed high-strength development of geopolymers10.1016/j.conbuildmat.2015.10.172 ↗
66. Ink-bottle effect in mercury intrusion porosimetry of cement-based materials10.1006/jcis.2001.7962 ↗