Enhanced tensile strength in an Al–Zn–Mg–Cu alloy via engineering the precipitates along the grain boundaries
Source abstract
Abstract
An investigation was conducted to study the influence of peak-ageing and double ageing treatments in the precipitation along the different grain boundary orientations of an extruded Al–Zn–Mg–Cu alloy. The results display that the peak-aged grain boundary precipitates along the Low Angle Grain Boundaries (LAGBs) are mainly of θ'' with the existence of few η′ precipitates, while the η′ and θ'' precipitates are along the High Angle Grain Boundaries (HAGBs). The major grain boundary precipitates are mainly of θ'' precipitates along LAGBs and θ′, η′, and η along the HAGBs after the double ageing treatment. The variation in the precipitate types along different grain boundary orientations was attributed to the different diffusion rates of solutes along the grain boundaries. In addition, it is observed that the yield strength (YS) (∼ 690 MPa) of peak-aged Al–Zn–Mg–Cu alloy increased by ∼ 73% and ∼ 18% by comparison with the extruded and double-aged alloys, respectively. The double-aged alloy displays good elongation to fracture (∼16%) compared to the peak-aged alloy. Precipitation hardening contributes to the tensile strength of the alloy, and the improvement of the elongation owed to the growth of the grain boundaries precipitates and the corresponding absence of the precipitate-free zone area. The current study provides new insights in engineering the grain boundary precipitates to the required precipitate type and the corresponding mechanical properties.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (58)
Show source-provided references
1. Precipitation behaviour in an Al-Zn-Mg-Cu alloy subjected to high strain rate compression tests10.1016/j.matchar.2021.111398 ↗
2. Microstructure evolution of an artificially aged Al-Zn-Mg-Cu alloy subjected to soft- and hard-steel core projectiles10.1016/j.jmrt.2020.08.076 ↗
3. Adiabatic shear band localization in an Al–Zn–Mg–Cu alloy under high strain rate compression10.1016/j.jmrt.2020.02.024 ↗
4. Microstructure characterization of 7055-T6, 6061-T6511 and 7A52-T6 Al alloys subjected to ballistic impact against heavy tungsten alloy projectile10.1016/j.acme.2019.10.001 ↗
5. Structure–property correlations in Al 7050 and Al 7055 high-strength aluminum alloys10.1016/j.msea.2007.05.116 ↗
6. Effect of heat treatment on the precipitate behaviour, corrosion resistance and high temperature tensile properties of 7055 aluminum alloy synthesis by novel spray deposited followed by hot extrusion10.1016/j.vacuum.2020.109185 ↗
7. Correlations between intergranular stress corrosion cracking, grain-boundary microchemistry, and grain-boundary electrochemistry for Al–Zn–Mg–Cu alloys10.1016/j.corsci.2010.08.024 ↗
8. Influence of RRA treatment on the microstructure and stress corrosion cracking behavior of the spray-formed 7075 alloy10.1007/s11003-015-9851-7 ↗
9. Stress corrosion cracking behaviour of 7xxx aluminum alloys: a literature review10.1016/S1003-6326(16)64220-6 ↗
10. Environmentally assisted fatigue-crack growth in 7075 and 7050 aluminum alloys10.1016/0036-9748(85)90310-2 ↗
11. Effect of heat treatment on solute concentration at grain boundaries in 7075 aluminum alloy10.1007/BF02643489 ↗
12. Grain boundary segregation in Al–Zn–Mg alloys—implications to stress corrosion cracking10.1007/BF02700441 ↗
13. Grain boundary ductile fracture in precipitation hardened aluminum alloys10.1016/0001-6160(87)90001-0 ↗
14. Grain boundary segregation engineering in metallic alloys: a pathway to the design of interfaces10.1016/j.cossms.2014.06.002 ↗
15. Effect of interface phase transformations on diffusion and segregation in high-angle grain boundaries10.1103/PhysRevLett.110.255502 ↗
16. Grain boundary segregation engineering and austenite reversion turn embrittlement into toughness: example of a 9 wt.% medium Mn steel10.1016/j.actamat.2014.12.021 ↗
17. The phase behavior of interfaces10.1126/science.1204204 ↗
18. Lejček · 201010.1007/978-3-642-12505-8 ↗
19. The stress corrosion susceptibility of 7075 Al–Zn–Mg–Cu alloys tempered from T6 to an overaged T7X10.5006/0010-9312-33.6.217 ↗
20. Role of grain-boundary precipitates and solute-depleted zone on the intergranular corrosion of aluminum alloy 715010.5006/1.3287699 ↗
21. Effect of Cu content on corrosion behavior of 7xxx series aluminum alloys10.1149/1.1695385 ↗
22. Microstructure and mechanical properties of an Al-Zn-Cu-Mg alloy processed by hot forming processes followed by heat treatments10.1016/j.matchar.2019.109901 ↗
23. Effect of deformation temperature on microstructure and mechanical properties of 7055 aluminum alloy after heat treatment10.1016/S1003-6326(13)62508-X ↗
24. Mechanical behaviors and microstructure characteristics of W-tempered and peak-aged 7075 alloy sheets under low frequency vibration–assisted tension10.1016/j.msea.2021.142338 ↗
25. The effect of strain rates on the microstructure and the mechanical properties of an over-aged Al-Zn-Mg-Cu alloy10.1016/j.matchar.2020.110472 ↗
26. Microstructure, mechanical properties and strengthening mechanism analysis in an AlMg5 aluminium alloy processed by ECAP and subsequent ageing10.3390/met8110969 ↗
27. Transmission Kikuchi diffraction in a scanning electron microscope: a review10.1016/j.mser.2016.10.001 ↗
28. Effects of solution time and cooling rate on microstructures and mechanical properties of 2219 Al alloy for a larger spun thin-wall ellipsoidal head10.1016/j.jmrt.2020.01.095 ↗
29. Effects of cold predeformation on dissolution of second-phase Al2Cu particles during solution treatment of 2219 Al–Cu alloy forgings10.1016/j.matchar.2017.10.026 ↗
30. Effect of heat treatments on the microstructures and tensile properties of an ultrafine-grained Al-Zn-Mg alloy processed by ECAP10.1016/j.jallcom.2018.03.206 ↗
31. Effect of ECAP processing on microstructure evolution and dynamic compressive behavior at different temperatures in an Al-Zn-Mg alloy10.1016/j.msea.2016.12.099 ↗
32. Structure analysis of embedded nano-sized particles by precession electron diffraction. η′-precipitate in an Al–Zn–Mg alloy as example10.1016/j.ultramic.2006.01.009 ↗
33. Multiple precipitation reactions and formation of θ'-phase in a pre-deformed Al–Cu alloy10.1016/j.msea.2018.07.039 ↗
34. In situ structural characterization of ageing kinetics in aluminum alloy 2024 across angstrom-to-micrometer length scales10.1016/j.actamat.2016.03.058 ↗
35. Phase transformation and dispersoid evolution for Al-Zn-Mg-Cu alloy containing Sn during homogenisation10.1016/j.jmrt.2019.08.055 ↗
36. Investigation of deformation induced precipitation and the related microstructure evolution of Al–Zn–Mg–Cu alloy10.1088/2053-1591/abc21b ↗
37. Huang · 2017
38. Characterization of precipitates in an Al-Zn-Mg alloy processed by ECAP and subsequent annealing10.1016/j.msea.2017.11.091 ↗
39. Mechanical properties of an Al-Zn-Mg alloy processed by ECAP and heat treatments10.1016/j.jallcom.2018.07.343 ↗
40. Microstructure characteristic of spray formed 7055 Al alloy subjected to ballistic impact by two different steel core projectiles impact10.1016/j.jmrt.2019.10.012 ↗
41. The nucleation and initial stages of growth of grain boundary precipitates in Al-Zn–Mg and Al–Mg alloys10.1016/0001-6160(69)90155-2 ↗
42. Effect of strain-induced precipitation on the low angle grain boundary in AA7050 aluminum alloy10.1016/j.matdes.2011.04.025 ↗
43. Segregation assisted grain boundary precipitation in a model Al–Zn–Mg–Cu alloy10.1016/j.actamat.2018.07.003 ↗
44. Grain boundary segregation and precipitation in aluminium alloys10.1016/S1359-6462(00)00577-7 ↗
45. Transition between low and high angle grain boundaries10.1016/j.actamat.2005.03.005 ↗
46. Grain boundary precipitation in an Al–Cu alloy10.1016/0001-6160(68)90131-4 ↗
47. Precipitation on grain boundaries in Al–Mg–Si alloys: the role of grain boundary misorientation10.1016/j.scriptamat.2021.114494 ↗
48. Effects of Cu content on the precipitation process of Al–Zn–Mg alloys10.1007/s10853-012-6714-6 ↗
49. First-principles study of solute-dislocation interaction in aluminum-rich alloys10.1103/PhysRevB.64.224203 ↗
50. Temperature dependence of amplitude-dependent internal friction due to simultaneous breakaway of a dislocation from several pinning points10.1016/S0921-5093(00)01792-5 ↗
51. Precipitation hardening10.1007/BF02670416 ↗
52. Mechanical properties of Al (Sc, Zr) alloys at ambient and elevated temperatures10.1016/S1359-6454(03)00320-3 ↗
53. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
54. Effect of dynamic plastic deformation on the microstructure and mechanical properties of an Al–Zn–Mg alloy10.1016/j.msea.2020.139287 ↗
55. Davis · 1993
56. Engineers-Sae · 2008
57. Heat treatment of 7xxx series aluminium alloys—some recent developments10.1016/S1003-6326(14)63306-9 ↗
58. Creep-age forming of AA7475 aluminum panels for aircraft lower wing skin application10.1590/S1516-14392012005000080 ↗