journal article·2023-05Open access

Microstructure, residual stress, and mechanical properties evolution of a Cu–Fe–P alloy under different conditions

Jingzhao Yang, Kun Bu, Yanjun Zhou, Kexing Song, Tao Huang, Xiaowen Peng, Haitao Liu, Yibo Du

Abstract

The evolution of the mechanical characteristics, residual stresses, and microstructure of a Cu–Fe–P alloy during machining was investigated, and the influence mechanism of the microstructure on the residual stress and strength of the Cu–Fe–P alloy was confirmed. The findings suggest that the tensile strength, transverse direction (TD), and rolling direction (RD) residual stresses in the cold-rolled state are 516 MPa, −80 MPa and −36 MPa, respectively, which are 76.1%, 93.8%, and 72.2% higher than those in the hot-rolled state, respectively. In addition, after annealing at high temperatures, the tensile strength, TD, and RD residual stresses of the Cu–Fe–P alloy decreased to 344 MPa, −9 MPa and −24 MPa, respectively, which were 33.3%, 88.8%, and 33.3% smaller than those of the cold-rolled alloy, respectively. The strength and residual stress of the Cu–Fe–P alloy are intriguing. The primary influencing aspects of the strength and residual stress are dislocations, grain boundaries, and textures. The residual stress of the Cu–Fe–P alloy may be controlled while maintaining strength by appropriately increasing the proportion of recrystallized grains and decreasing the dislocation density and volume fraction of the Brass texture, respectively. These outcomes serve as a guide for improving the service performance of Cu–Fe–P alloys.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. A promising structure for fabricating high strength and high electrical conductivity copper alloys
2. Composition design, phase transition and fabrication of copper alloys with high strength and electrical conductivity
3. Diffraction analysis of α-Fe precipitates in a polycrystalline Cu-Fe alloy10.1016/j.matchar.2015.05.012 ↗
4. Strengthening mechanisms of Fe nanoparticles for single crystal Cu-Fe alloy10.1016/j.msea.2015.03.081 ↗
5. Influence of P content on microstructure and texture evolution of the Oxygen-Free copper10.3390/met12101622 ↗
6. Effect of thermomechanical treatments on microstructure and properties of Cu-base leadframe alloy10.1023/A:1004830000742 ↗
7. Influence of short-time annealing on the evolution of the microstructure, mechanical properties and residual stress of the C19400 alloy strips10.1016/j.jallcom.2023.168705 ↗
8. Theoretical study of particle dissolution during homogenization in Cu-Fe-P alloy10.3390/met8060455 ↗
9. Microstructure and properties of Cu-2.3Fe-0.03P alloy during thermomechanical treatments10.1016/S1003-6326(15)63757-8 ↗
10. Investigation of the retained austenite orientation in iron precipitates of martensitic transformation10.1016/j.matlet.2020.128556 ↗
11. Pinning of grain boundaries by second phase particles in equal-channel angularly pressed Cu-Fe-P alloy10.1016/j.msea.2006.05.081 ↗
12. Study on high-strength and high-conductivity Cu-Fe-P alloys10.1016/j.msea.2006.01.068 ↗
13. Effect of annealing temperature on dual-structure coexisting precipitates in Cu-2.18Fe-0.03P alloy and softening mechanism at high temperature10.1007/s10853-022-07910-5 ↗
14. Hot deformation behavior of Cu-Fe-P alloys during compression at elevated temperatures10.1016/j.jmatprotec.2008.06.048 ↗
15. Effects of C addition and thermo-mechanical treatments on microstructures and properties of Cu-Fe-P alloys10.1016/j.msea.2011.10.041 ↗
16. Effect of stacking fault energy on mechanical behavior of bulk nanocrystalline Cu and Cu alloys10.1016/j.actamat.2011.05.052 ↗
17. Mechanism of texture formation in submicron Cu thin films10.1016/j.jmrt.2021.08.154 ↗
18. Effect of stretch-bending straightening on the residual stress of C19400 alloy strips
19. Microstructure and mechanical properties of additive manufactured copper alloy10.1016/j.matlet.2016.05.064 ↗
20. Structure and properties evolution of Cu-2.5Fe-0.03P alloy under different treatment conditions
21. Residual stress-microstructure-mechanical property interrelationships in multipass HSLA steel welds10.1016/j.jmatprotec.2016.01.020 ↗
22. Improving the mechanical properties of pure magnesium through cold hydrostatic extrusion and low-temperature annealing10.1016/j.msea.2014.12.104 ↗
23. Insights of texture and microstructure evolution in the short time annealing of Al-Cu-Mg alloy at large temperature range10.1016/j.jallcom.2021.159613 ↗
24. The dependence of final microstructure, texture evolution and mechanical properties of Al-Mg-Si-Cu alloy sheets on the intermediate annealing10.1016/j.msea.2015.02.029 ↗
25. Influence of low-temperature annealing temperature on the evolution of the microstructure and mechanical properties of Cu-Cr-Ti-Si alloy strips10.1016/j.msea.2020.140120 ↗
26. Hardening by annealing and softening by deformation in nanostructured metals10.1126/science.1124268 ↗
27. Residual stress in α-brass during annealing10.4028/www.scientific.net/MSF.571-572.69 ↗
28. Correlation mechanism of grain orientation/microstructure and mechanical properties of Cu-Ni-Si-Co alloy10.1016/j.msea.2021.141239 ↗
29. Microstructure, microhardness and residual stress of laser additive manufactured CoCrFeMnNi high-entropy alloy subjected to laser shock peening10.1016/j.jmatprotec.2020.116806 ↗