Effect of electrical parameters on the growth and properties of 7075 aluminum alloy film based on scanning micro-arc oxidation with mesh electrode
Source abstract
Abstract
The effect of electrical parameters on the properties of 7075 aluminum alloy films under scanning micro-arc oxidation was studied. The process of micro-arc oxidation is simulated in this paper. This method greatly reduces the experimental cost of micro-arc oxidation research and provides a new idea for the subsequent research of micro-arc oxidation. The micro-arc oxidation process was simulated by COMSOL Multiphysics. The film thickness, hardness and corrosion resistance are used as indexes, and forward voltage, positive duty cycle and pulse frequency are used as design factors to carry out orthogonal experiments with three factors and three indexes. Vega XMU scanning electron microscope is used to observe the surface and section morphology of the micro-arc oxidation film. VERSA STAT 3 F electrochemical workstation is used to detect the potentiodynamic polarization curve of the film and Tafel fitting is performed to obtain the self-corrosion potential (Ecorr). The thickness and hardness of the film are tested by Nix coating thickness tester and HV-1000 Vickers hardness tester. The results show that the film uniformity of the network electrode is better than that of the tube electrode under the condition of scanning micro-arc oxidation. The order of electrical parameters affecting film thickness and hardness is forward voltage > forward duty cycle > pulse frequency. The order of the electrical parameters affecting the corrosion resistance of the film is pulse frequency > forward voltage > forward duty cycle. The best combination of electrical parameters is: forward voltage 500 V, forward duty ratio 30%, pulse frequency 200 Hz.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Metal and Thin Film Mechanics · Electrodeposition and Electroless Coatings
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. The effect of the diffusive, composite chromium nitride layers produced by a hybrid surface treatment on the corrosion behavior of AZ91D magnesium alloy10.1016/j.vacuum.2011.01.016 ↗
2. Properties of micro-arc oxidation coatings on 5052 Al alloy sealed by SiO2 nanoparticles10.3390/coatings12030373 ↗
3. Iridium-Doped nanosized Zn–Al layered double hydroxides as efficient water oxidation catalysts10.1021/acsami.0c07925 ↗
4. The preparation and properties of black coating by micro arc oxidation on 2A12 aluminum alloy10.1016/j.matlet.2018.11.019 ↗
5. Microstructure and properties of microarc oxidation coating formed on aluminum alloy with compound additives nano-TiO2 and nano-ZnO10.1007/s12598-017-0948-z ↗
6. Improvement of corrosion resistance of pure magnesium in Hanks' solution by microarc oxidation with sol–gel TiO2 sealing10.1016/j.jallcom.2008.01.102 ↗
7. Microstructure and properties of sol-enhanced Co-P-TiO2 nano-composite coatings10.1016/j.jallcom.2019.04.047 ↗
8. Measurement of adhesion strength of Al electroplating film on AZ31, AZ61, and AZ91 substrates10.1149/07515.0297ecst ↗
9. New sealing treatment of microarc oxidation coating10.1179/1743294413Y.0000000195 ↗
10. Microstructure characteristic of ceramic coatings fabricated on magnesium alloys by micro-arc oxidation in alkaline silicate solutions10.1016/j.apsusc.2005.09.067 ↗
11. A review-black oxide coating on metal substrates of steels, aluminium, magnesium and copper10.4028/www.scientific.net/AST.106.46 ↗
12. Effect of Al2O3 micro-powder additives on the properties of micro-arc oxidation coatings formed on 6061 aluminum alloy10.1007/s11665-016-2255-5 ↗
13. Cu–Sn–Zn nanocomposite coatings prepared by TiO2 sol-enhanced electrodeposition10.1007/s10800-020-01442-z ↗
14. Anomalous layer-thickening during micro-arc oxidation of 6061 Al alloy10.1016/j.jallcom.2016.11.372 ↗
15. Influence of secondary phases of AlSi9Cu3 alloy on the plasma electrolytic oxidation coating formation process10.1016/j.jmst.2019.12.031 ↗
16. Microstructure and corrosion resistance of Ti3O5-HA bio-ceramic coating fabricated on AZ80 magnesium alloy10.1016/j.surfcoat.2017.06.055 ↗
17. The outward–inward growth behavior of microarc oxidation coatings in phosphate and silicate solution10.1016/j.matlet.2010.06.053 ↗
18. Preparation and performance of alumina ceramic coating doped with aluminum nitride by micro arc oxidation10.1016/j.ceramint.2020.03.179 ↗
19. Growth characteristics of plasma electrolytic oxidation ceramic coatings on Ti–6Al–4V alloy10.1016/j.apsusc.2007.12.062 ↗
20. Excellent corrosion resistance of P and Fe modified micro-arc oxidation coating on Al alloy10.1016/j.jallcom.2017.03.303 ↗
21. Surface treatment of Zn-Mn-Mg alloys by micro-arc oxidation in silicate-based solutions with different NaF concentrations10.3390/ma14154289 ↗
22. Incorporation of MoO2 and ZrO2 particles into the oxide film formed on 7075 Al alloy via micro-arc oxidation10.1016/j.matlet.2016.07.009 ↗
23. Study of scanning micro-arc oxidation and coating development10.1007/s11665-017-2861-x ↗
24. Study on scanning Micro-arc oxidation technology applied to 2024 aluminum alloy:study on scanning Micro-arc oxidation technology applied to 2024 aluminum alloy
25. Microarc oxidation of 2024 Al alloy using spraying polar and its influence on microstructure and corrosion behavior10.1016/j.surfcoat.2013.04.013 ↗
26. The structure and properties of Al2O3 and Al coatings deposited by microarc oxidation on graphite substrates10.1134/1.1787669 ↗
27. Degradation and structure evolution in corrosive LiOH solution of microarc oxidation coated Zircaloy-4 alloy in silicate and phosphate electrolytes10.1016/j.apsusc.2017.04.226 ↗
28. Dependence of the infrared emissivity on SiC content and microstructure of microarc oxidation ceramic coatings formed in Na2SiO3 electrolyte10.1016/j.apsusc.2017.06.166 ↗
29. Effects of different electrolytes for micro-arc oxidation on the bond strength between titanium and porcelain10.1016/j.jpor.2016.11.001 ↗
30. High-corrosion resistance of the microarc oxidation coatings on magnesium alloy obtained in potassium fluorinate electrolytes10.1016/j.surfcoat.2015.01.013 ↗
31. Effect of NaOH concentration on microstructure and corrosion resistance of MAO coating on cast Al− Li alloy10.1016/S1003-6326(21)65549-8 ↗
32. Effect of Na2SiO3 solution concentration of micro-arc oxidation process on lap-shear strength of adhesive-bonded magnesium alloys10.1016/j.apsusc.2014.06.117 ↗
33. Preparation of dark-red membrane by micro-arc oxidation on AM50 alloys10.1080/10426914.2015.1004688 ↗
34. Study on the preparation of titania films for photocatalytic application by micro-arc oxidation10.1016/j.solmat.2006.03.017 ↗
35. Study of biocompatibility in ceramic coating doped with NaF on Ti-3Zr-2Sn-3Mo-25Nb by micro-arc oxidation10.1080/00202967.2021.1952790 ↗
36. Optimisation of process parameters and characterisation of composite ceramic coating with NaF additive on Ti-3Zr-2Sn-3Mo-25Nb by micro-arc oxidation10.1080/00202967.2020.1819018 ↗