Optimization of welding parameters on welding distortion and stress in S690 high-strength steel thin-plate structures
Source abstract
Abstract
This study examines the impact of welding heat input on the residual stress and welding deformation of large, thin-walled constructions made of ultra-high strength steel using a single shot calculation method. These structures are susceptible to warpage distortion after welding, which negatively affects production precision. The study uses an interactive orthogonal experimental design to optimize welding parameters and investigate their influence on deformation. Results reveal that welding speed has the most significant impact on deformation, followed by welding voltage and current. The optimal welding parameters (v = 60 cm/min, I = 160 A, U = 16 V) are validated through simulation and experiment, which reduce deformation by 5.4%. After optimization, the pump arm's side bending volume and warpage volume decrease by 4.06% and 9.56%, respectively, and welding deformation significantly reduces. Experimental verification shows a maximum error of 2.6%, indicating the accuracy of the finite element model. This study provides a theoretical basis for improving the performance of welding large, thin-walled box structures.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. Tensile behaviour of S690QL and S960QL under high strain rate10.1016/j.jcsr.2018.08.009 ↗
2. Combined effect of elevated temperature and high strain rates on S690QL high strength steel10.1016/j.jcsr.2022.107519 ↗
3. Strain-rate effects on S690QL high strength steel under tensile loading10.1016/j.jcsr.2020.106348 ↗
4. Direct measurements and numerical predictions of welding-induced initial deformations in a full-scale steel stiffened plate structure10.1016/j.tws.2020.106786 ↗
5. Influence of contact behavior on welding distortion and residual stress in a thin-plate butt-welded joint performed by partial-length welding10.1016/j.tws.2022.109302 ↗
6. Numerical simulation of welding distortion in large structures10.1016/j.cma.2007.05.023 ↗
7. Experimental evidence on structural adequacy of high strength S690 steel welded joints with different heat input energy10.1016/j.engstruct.2019.110051 ↗
8. Experimental investigation and numerical analyses of residual stresses and distortions in GMA welding of thin dissimilar AA5052-AA6061 plates10.1016/j.jmapro.2016.12.017 ↗
9. Controlling angular distortion in high strength low alloy steel thick-plate T-joints10.1016/j.jmatprotec.2018.12.023 ↗
10. Prediction of welding distortion and residual stress in a thin plate butt-welded joint10.1016/j.commatsci.2007.12.006 ↗
11. Review on finite element analysis of welding deformation and residual stress10.1080/13621718.2017.1361673 ↗
12. Review on mitigation of welding-induced distortion based on FEM analysis10.5781/JWJ.2020.38.1.6 ↗
13. Determination of welding deformation in fillet-welded joint by means of numerical simulation and comparison with experimental measurements10.1016/j.jmatprotec.2006.10.013 ↗
14. Theoretical prediction of welding distortion in large and complex structures10.1007/s11706-010-0019-y ↗
15. A review on methodologies to reduce welding distortion10.1016/j.matpr.2018.10.272 ↗
16. Influence of the welding speed on the distortion of thin stainless steel plates—numerical and experimental investigations in the framework of the food industry machines10.1016/j.jmatprotec.2015.07.021 ↗
17. Effects of welding parameters and welding sequence on residual stress and distortion in Al6061-T6 aluminum alloy for T-shaped welded joint10.1016/S1003-6326(19)65181-2 ↗
18. Finite element analysis of heat input effect on temperature, residual stresses and distortion in butt welded plates10.1016/j.matpr.2017.11.525 ↗
19. Multi-objective optimization of gas metal arc welding parameters and sequences for low-carbon steel (Q345D) T-joints10.1016/S1006-706X(17)30082-1 ↗
20. Effect of welding heat input on welding deformation of bogie side beam of high-speed EMU and optimization
21. Investigation on welding distortion in stainless steel sheet using gas tungsten arc welding process10.1016/j.matpr.2020.07.264 ↗
22. Parametric study of friction stir welding induced distortion in thin aluminium alloy plates: a coupled numerical and experimental analysis10.1016/j.tws.2018.10.027 ↗
23. Mathematical analysis of the effects of input parameters on angular distortion of MIG welded aluminium 8011 plates10.1016/j.matpr.2021.12.095 ↗
24. Optimization of MIG welding parameters to control the angular distortion in Fe410WA steel10.1080/10426914.2015.1127939 ↗
25. Noor · 2011
26. Simulation-based numerical optimization of arc welding process for reduced distortion in welded structures10.1016/j.finel.2014.02.003 ↗
27. Evaluation of factors that affect rutting resistance of asphalt mixes by orthogonal experiment design10.1016/j.ijprt.2017.03.008 ↗
28. Numerical optimization of the welding sequence for mitigating welding deformation in aluminum pipe structures by using a genetic algorithm10.1007/s12541-020-00420-x ↗
29. Numerical simulation and test study on track welding of QTT
30. Chinella · 2011
31. Experimental-based methodology for the double ellipsoidal heat source parameters in welding simulations10.1007/s40868-020-00074-4 ↗
32. Optimized segmented heat source for the numerical simulation of welding-induced deformation in large structures10.1016/j.advengsoft.2017.12.005 ↗
33. Numerical computation methods of welding deformation and their application in bogie frame for high-speed trains10.1016/j.jmapro.2019.01.013 ↗
34. Numerical prediction of welding deformation in ship block subassemblies via the inhomogeneous inherent strain method10.1016/j.jmapro.2022.06.044 ↗
35. Prediction of welding distortion in butt joint of thin plates10.1016/j.matdes.2009.05.004 ↗
36. Influence of heat input on welding induced distortion for Yb-fibre laser welded thin sheets10.1016/j.matpr.2020.02.442 ↗