Accelerated recrystallization behavior of commercially pure titanium subjected to an alternating-current electropulse
Source abstract
Abstract
Electropulsing has various engineering benefits compared with the traditional heating method. This study investigated the effect of electropulsing treatment on the recrystallization behavior of commercially pure titanium (CP–Ti) according to the electropulsing duration and direction. The application of a 2-s electropulse barely caused recrystallization, whereas a 4-s electropulse caused microstructural evolutions that significantly varied with the electropulsing direction and the observed sections (i.e., center, quarter, and edge). Static recrystallization was completed in the center section through the application of a 4-s electropulse at a current density of 29 A·mm−2, which suggests the accelerated recrystallization capability of electropulsing. Under the same conditions, electropulsing along the rolling direction of the CP-Ti sheet exhibited a higher recrystallization rate than that along the transverse direction. This is attributed to the different arrangement of the grain boundaries between the two samples.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electromagnetic Effects on Materials · Material Properties and Failure Mechanisms
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Mechanical flow anisotropy in severely deformed pure titanium10.1016/j.msea.2006.06.082 ↗
2. Grain refinement and properties of pure Ti processed by warm ECAP and cold rolling10.1016/S0921-5093(02)00366-0 ↗
3. Orientation effect on mechanical properties of commercially pure titanium at room temperature10.1007/s11661-006-9040-2 ↗
4. Anisotropic yielding behavior of rolling textured high purity titanium10.1016/j.msea.2015.03.096 ↗
5. Microstructures and mechanical properties of ultrafine-grained Ti foil processed by equal-channel angular pressing and cold rolling10.1557/JMR.2003.0138 ↗
6. Improvement of stretch formability of pure titanium sheet by differential speed rolling10.1016/j.scriptamat.2010.05.005 ↗
7. Production of ultrafine-grained titanium with suitable properties for dental implant applications by RS-ECAP process
8. Annealing behavior of coarse-grained titanium deformed by cold rolling10.1016/j.msea.2005.11.041 ↗
9. Deformation mechanisms in austenitic TRIP/TWIP steel as a function of temperature10.1007/s11661-014-2684-4 ↗
10. Effects of specimen and grain size on electrically-induced softening behavior in uniaxial micro-tension of AZ31 magnesium alloy: experiment and modeling10.1016/j.matdes.2017.04.064 ↗
11. Constitutive analysis of electrically-assisted tensile deformation of CP-Ti based on non-uniform thermal expansion, plastic softening and dynamic strain aging10.1016/j.ijplas.2017.02.012 ↗
12. Performance analysis, challenges and future perspectives of nickel based nanostructured electrodes for electrochemical supercapacitors10.1016/j.jmrt.2021.01.027 ↗
13. Evaluation of the athermal effect of electric pulsing on the recovery behavior of magnesium alloy10.1007/s11661-016-3804-0 ↗
14. Microcrack healing and local recrystallization in pre-deformed sheet by high density electropulsing10.1016/j.msea.2007.12.037 ↗
15. Nanocrystallization and enhanced surface mechanical properties of commercial pure titanium by electropulsing-assisted ultrasonic surface rolling10.1016/j.matdes.2018.04.027 ↗
16. Experimental investigation into the electropulsing assisted pulsating gas forming of CP-Ti tubes10.1016/j.jmatprotec.2019.116492 ↗
17. Effect of electric current heat treatment on commercially pure titanium sheets10.3390/met11050783 ↗
18. Structural and phase changes under electropulse treatment of fatigue-loaded titanium alloy VT1-010.1016/j.jmrt.2018.09.008 ↗
19. Effect of high-density electropulsing on microstructure and mechanical properties of cold-rolled TA15 titanium alloy sheet10.1016/j.jallcom.2008.03.027 ↗
20. Manufacturing ultrafine-grained Ti-6Al-4V bulk rod using multi-pass caliber-rolling10.3390/met5020777 ↗
21. Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium10.1016/j.msea.2005.03.019 ↗
22. Prediction of electropulse-induced nonlinear temperature variation of Mg alloy based on machine learning10.3365/KJMM.2020.58.6.413 ↗
23. Tailoring strength-ductility balance of caliber-rolled AZ31 Mg alloy through subsequent annealing10.1016/j.jma.2019.11.005 ↗
24. Welsch · 1993
25. Recrystallization and grain growth in highly cold worked CP-Titanium10.1016/j.msea.2010.03.023 ↗
26. Effect of electric current on the recrystallization behavior of cold worked α - Ti10.1016/S0036-9748(88)80331-4 ↗
27. Effect of pre-annealing strains on annealing texture developments in commercially pure (CP) titanium10.1080/14786435.2015.1020905 ↗
28. Effect of electric current on recrystallization kinetics in interstitial free steel and AZ31 magnesium alloy10.1016/j.matchar.2017.09.021 ↗
29. A review of electrically-assisted manufacturing10.1007/s40684-015-0045-4 ↗
30. Electroplasticity in metals and ceramics10.1016/S0921-5093(00)00786-3 ↗
31. Effect of cold rolling reduction rate on mechanical properties and electrical conductivity of Cu–Ni–Si alloy prepared by temperature controlled mold continuous casting10.1016/j.msea.2019.138068 ↗
32. Effect of electropulsing on anisotropy behaviour of cold-rolled commercially pure titanium sheet10.1016/S1003-6326(10)60079-9 ↗
33. Effect of electropulsing treatment on microstructure and mechanical behavior of Ti-6Al-4V alloy sheet under argon gas protection10.1016/j.vacuum.2017.11.017 ↗