journal article·2023-03Open access

Research on inverse identification of johnson-cook constitutive parameters for turning 304 stainless steel based on coupling simulation

Zichuan Zou, Lin He, Tao Zhou, Wenqian Zhang, Pengfei Tian, Xiaorong Zhou

Abstract

The constitutive model plays a decisive role in the accuracy and reliability of the simulation results. Because the material flow characteristics obtained by the traditional experimental method are difficult to describe thermoplastic deformation behavior in the cutting process accurately, and the inverse identification is usually carried out based on a two-dimensional orthogonal cutting model, ignoring the actual cutting state, which leads to significant deviations in the results of parameter identification. Therefore, a three-dimensional (3-D) turning finite element simplified model which conforms to the actual cutting scenario was established. Based on this model, a coupling simulation was used to inverse identify the Johnson-Cook (J-C) parameters for turning 304 stainless steel. Firstly, the automatic finite element modeling and calculation of 3-D turning is implemented by Python. Then, the inverse identification framework was built based on the ISIGHT. The initial yield strength of J-C parameters was obtained from quasi-static compression experiments. With the objective function of minimizing the error between the experimental cutting force and the simulated cutting force, the inverse identification of J-C parameters (strain reinforcement factor, strain rate sensitivity, thermal softening index, and hardening index) was carried out by a multi-island genetic algorithm. Finally, compared with cutting forces, chip morphology, and residual stresses, the feasibility of the inverse identification method and the accuracy of the constitutive model is demonstrated, which also provides a reference for the optimal identification method of constitutive parameters of difficult-to-machine materials.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Surface Polishing Techniques · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. End milling of AISI 304 steel using minimum quantity lubrication10.1016/j.measurement.2019.01.064 ↗
2. Superior mechanical properties and deformation mechanisms of a 304 stainless steel plate with gradient nanostructure10.1016/j.ijplas.2022.103336 ↗
3. Investigation of stress corrosion cracking initiation in machined 304 austenitic stainless steel in magnesium chloride environment10.1007/s11665-020-04558-7 ↗
4. Wear performance of surface treated drills in high speed drilling of AISI 304 stainless steel10.1016/j.jmapro.2020.08.022 ↗
5. Dislocation-mechanics-based constitutive relations for material dynamics calculations10.1063/1.338024 ↗
6. Constitutive equations for elastic-viscoplastic strain-hardening materials10.1115/1.3423586 ↗
7. On the mechanism of hot deformation10.1016/0001-6160(66)90207-0 ↗
8. A constitutive model and data for materials subjected to large strains, high strain rates, and high temperatures
9. Modified material constitutive models for serrated chip formation simulations and experimental validation in machining of titanium alloy Ti–6Al–4V10.1016/j.ijmachtools.2010.08.004 ↗
10. Serrated chip formation and their adiabatic analysis by using the constitutive model of titanium alloy in high speed cutting10.1016/j.jallcom.2014.12.230 ↗
11. FE simulation of machining of Ti-54M titanium alloy for industry relevant outcomes10.1016/j.measurement.2018.07.017 ↗
12. Numerical analysis of constitutive coefficients effects on FE simulation of the 2D orthogonal cutting process: application to the Ti6Al4V10.1007/s00170-016-8934-4 ↗
13. Modification of strain rate strengthening coefficient for Johnson-Cook constitutive model of Ti6Al4V alloy
14. Investigation of tensile Johnson-Cook model parameters for Nimonic 80A superalloy10.1016/j.jallcom.2019.06.153 ↗
15. A modified Johnson–Cook model of dynamic tensile behaviors for 7075-T6 aluminum alloy10.1016/j.jallcom.2014.09.002 ↗
16. Holland · 1992
17. Ant system: optimization by a colony of cooperating agents10.1109/3477.484436 ↗
18. Research on parameter identification of johnson–cook constitutive model for TC17 titanium alloy cutting simulation10.1016/j.mtcomm.2022.103772 ↗
19. 3D FEM simulation of the turning process of stainless steel 17-4PH with differently texturized cutting tools10.1016/j.ijmecsci.2019.03.016 ↗
20. Modified primary shear zone analysis for identification of material mechanical behavior during machining process using genetic algorithm10.1115/1.4006768 ↗
21. Determination of Johnson–Cook parameters from machining simulations10.1016/j.commatsci.2011.07.035 ↗
22. Predictive modelling of microstructure changes, micro-hardness and residual stress in machining of 304 austenitic stainless steel10.1016/j.ijmachtools.2018.03.008 ↗
23. A quantitative analysis of the transition of fracture mechanisms of Ti6Al4V over a wide range of stress triaxiality and strain rate10.1016/j.engfracmech.2020.107020 ↗
24. A constitutive model for Ti6Al4V considering the state of stress and strain rate effects10.1016/j.mechmat.2019.103103 ↗
25. Machining simulation of Ti6Al4V using coupled Eulerian-Lagrangian approach and a constitutive model considering the state of stress10.1016/j.simpat.2021.102312 ↗
26. Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures10.1016/0013-7944(85)90052-9 ↗
27. On the mechanisms of ductile failure in high-strength steels subjected to multi-axial stress-states10.1016/0022-5096(76)90024-7 ↗
28. Numerical investigation of sequential cuts residual stress considering tool edge radius in machining of AISI 304 stainless steel10.1016/j.simpat.2022.102525 ↗
29. Astakhov · 2006
30. Cutting force modeling: genesis, state of the art, and development10.1007/978-3-030-90487-6_2 ↗
31. Inter-relationship between shear processes occurring along tool face and shear plane in metal cutting
32. Experimental and numerical study on the laser shock welding of aluminum to stainless steel10.1016/j.optlaseng.2018.11.012 ↗
33. Simple estimation method for strain rate sensitivity based on the difference between the indentation sizes formed by spherical-shaped impactors10.1016/j.ijmecsci.2020.106007 ↗
34. The influence of charge geometry on the response of partially confined right circular stainless steel cylinders subjected to blast loading10.1016/j.ijimpeng.2017.02.015 ↗
35. Numerical and experimental investigation on aluminum 6061-V-grooved stainless steel 304 explosive cladding
36. Thermo-viscoplastic behavior and constitutive relations for 304 austenitic stainless steel over a wide range of strain rates covering quasi-static, medium, high and very high regimes10.1016/j.ijimpeng.2022.104208 ↗
37. Multiple ballistic impacts on 2024-T4 aluminum alloy by spheres: experiments and modelling10.1016/j.jmst.2021.04.012 ↗
38. A novel technique for dynamic shear testing of bulk metals with application to 304 austenitic stainless steel10.1016/j.ijsolstr.2020.08.019 ↗
39. Machining residual stresses in AISI 316L steel and their correlation with the cutting parameters10.1081/MST-120005959 ↗