Effects of TiB2 additions on microstructure and mechnical properties of Al–Mg–Sc alloy fabricated by selective laser melting
Source abstract
Abstract
In this paper, the effect of TB2 additions on a noval Al–Mg–Sc alloy was studied, and the microstructure and mechanical properties of SLM-fabricated TiB2/Al–Mg–Sc alloys were investigated. The results showed that molten pool width increased and molten pool depth slightly decreased with TiB2 increase, due to the laser absorptivity of the TiB2/Al–Mg–Sc alloys higher than that of Al–Mg–Sc alloy under the same process parameters. The microstructure of SLM-fabricated TiB2Al–Mg–Sc alloys were composed of fine-grained, coarse-grained and columnar-grained regions, and the fine-grained region increased with the increase of TiB2 content. The recrystallization regions in SLM-fabricated TiB2/Al–Mg–Sc alloy decreased with the increase of TiB2 content, and TiB2 additions used as heterogeneous nucleation to refine grains, which can pin grain boundaries and prevent recrystallization during SLM process. TiB2/Al–Mg–Sc alloy with 1% TiB2 additions showed a relatively higher comprehensive mechanical properties, and the tensile strength is 483 MPa, the elongation is 15.8%. Tensile strength of 1%TiB2/Al–Mg–Sc alloy was increased by 37 MPa and the elongation is also increased by 2.1% compared with 0%TiB2/Al–Mg–Sc alloy, and 2%TiB2/Al–Mg–Sc alloy shown a relatively lower comprehensive mechanical properties due to its lower density and TB2 agglomerated.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
2. Alloy design via additive manufacturing: advantages, challenges, applications and perspectives10.1016/j.mattod.2021.11.026 ↗
3. Metal additive manufacturing: a review10.1007/s11665-014-0958-z ↗
4. Metal alloys for fusion-based additive manufacturing10.1002/adem.201700952 ↗
5. Metal powders in additive manufacturing: a review on reusability and recyclability of common titanium, nickel and aluminum alloys
6. Heat treatment of aluminium alloys produced by laser powder bed fusion: a review10.1016/j.matdes.2021.109651 ↗
7. Strength and strain hardening of a selective laser melted AlSi10Mg alloy10.1016/j.scriptamat.2017.07.025 ↗
8. 3D printing of high-strength aluminium alloys10.1038/nature23894 ↗
9. Selective laser melting of nano-TiB 2 decorated AlSi10Mg alloy with high fracture strength and ductility10.1016/j.actamat.2017.02.062 ↗
10. Grain refinement in laser manufactured Al-based composites with TiB2 ceramic10.1016/j.jmrt.2020.04.059 ↗
11. Selective laser melting additive manufacturing of TiC/AlSi10Mg bulk-form nanocomposites with tailored microstructures and properties10.1016/j.phpro.2014.08.153 ↗
12. Simultaneous enhancement of strength, ductility, and hardness of TiN/AlSi10Mg nanocomposites via selective laser melting
13. A heat treatable TiB2/Al-3.5Cu-1.5Mg-1Si composite fabricated by selective laser melting: microstructure, heat treatment and mechanical properties10.1016/j.compositesb.2018.04.026 ↗
14. Selective laser melting Al-3.4Mg-0.5Mn-0.8Sc-0.4Zr alloys: from melting pool to the microstructure and mechanical properties10.1016/j.msea.2021.141889 ↗