journal article·2023-07Open access

Investigating the influence of PVA and PP fibers on the mechanical, durability, and microstructural properties of one-part alkali-activated mortar: An experimental study

Sohaib Nazar, Jian Yang, Muhammad Nasir Amin, Muhammad Husnain, Faraz Ahmad, Hisham Alabduljabbar, Ahmed Farouk Deifalla

Abstract

Alkali-activated materials (AAMs) have gained significant attention in recent years due to their potential for sustainable construction and outstanding strength and durability characteristics. However, their wide application is constrained by their weak behavior under flexure and tensile loading, leading to brittleness. This study examines the formulation of an alkali-activated fiber-reinforced mortar, using fly ash and hydrated lime as main precursors, and investigates the capacity when reinforced with polyvinyl alcohol (PVA) and polypropylene (PP) fibers. The performance was measured through experimental investigation in terms of flowability, setting time, compressive strength (CS), water absorption, flexure strength (FS), and load-displacement curve under flexure loading. The durability was assessed through acid and sulfate attack tests after 120 days. The findings showed that adding both types of fibers improved the mechanical and durability performance of the one-part AAM. The highest CS of 44.95 MPa and 42.04 MPa and FS of 7.8 MPa and 6.9 MPa were achieved for PVA and PP fibers at a 1.5% fiber content. The FS was increased by 18.94 % and 28.2% for PP1.5 and PVA1.5 fibers respectively. The control sample, PP 1.5 and PVA 1.5 recorded 31.1%, 12.5%, and 11% loss in CS after the acid attack test, respectively, after 120 days. A reduction of 15.3% and 13.3% was recorded in flow diameter with the addition of PP and PVA fibers at 2%. Overall, mortars reinforced with PVA fibers have shown better flowability, mechanical strength, and chemical resistance than PP fibers.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Magnesium Oxide Properties and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Ultra-high-ductile behavior of a polyethylene fiber-reinforced alkali-activated slag-based composite10.1016/j.cemconcomp.2016.04.002 ↗
2. Formulation and characterization of cleaner one-Part Novel fly ash/lime-based alkali-activated material10.1016/j.jmrt.2023.02.022 ↗
3. Formulation and characterization of cleaner one-part novel fly ash/lime-based alkali-activated material10.1016/j.jmrt.2023.02.022 ↗
4. Artificial neural network with a cross-validation technique to predict the material design of eco-friendly engineered geopolymer composites10.3390/ma15103443 ↗
5. Development of rubberized geopolymer interlocking bricks
6. Effects of sand/fly ash and the water/solid ratio on the mechanical properties of engineered geopolymer composite and mix design optimization10.3390/min10040333 ↗
7. Long-term durability properties of geopolymer concrete: an in-depth review
8. Estimation of strength, rheological parameters, and impact of raw constituents of alkali-activated mortar using machine learning and SHapely Additive exPlanations (SHAP)10.1016/j.conbuildmat.2023.131014 ↗
9. Development and characterization of fly ash based PVA fiber reinforced Engineered Geopolymer Composites incorporating metakaolin10.1016/j.cemconcomp.2020.103521 ↗
10. Artificial neural network with a cross-validation technique to predict the material design of eco-friendly engineered geopolymer composites10.3390/ma15103443 ↗
11. Mechanical properties of geopolymer composites reinforced with natural fibers10.1016/j.proeng.2016.07.395 ↗
12. Fiber-reinforced one-part alkali-activated slag/ceramic binders10.1016/j.ceramint.2018.02.097 ↗
13. The effect of polypropylene fiber with different length and dosage on the performance of alkali-activated slag mortar10.1016/j.conbuildmat.2021.124978 ↗
14. Tensile behavior and microstructure of hybrid fiber ambient cured one-part engineered geopolymer composites10.1016/j.conbuildmat.2018.07.012 ↗
15. Comparative deflection hardening behavior of short fiber reinforced geopolymer composites10.1016/j.conbuildmat.2014.07.085 ↗
16. High ductile behavior of a polyethylene fiber-reinforced one-part geopolymer composite: a micromechanics-based investigation10.1016/j.acme.2016.12.005 ↗
17. High-strength high-ductility engineered/strain-hardening cementitious composites (ECC/SHCC) incorporating geopolymer fine aggregates10.1016/j.cemconcomp.2021.104296 ↗
18. Alkali-activated and geopolymer materials developed using innovative manufacturing techniques: a critical review10.1016/j.conbuildmat.2021.124483 ↗
19. Engineering properties of PVA fibre-reinforced geopolymer mortar containing waste oyster shells10.3390/ma15197013 ↗
20. Characteristic of Fresh and Harden Properties of Polyvinyl Alcohol Fibre Reinforced Alkali Activated Composite10.32604/jrm.2022.023266 ↗
21. Influence of ternary hybrid fibers on the mechanical properties of ultrahigh-strength concrete10.3389/fmats.2023.1148589 ↗
22. Comparative study on the effect of fiber type and content on the performance of one-part alkali-activated mortar10.1016/j.conbuildmat.2020.118221 ↗
23. Improvement of early strength of fly ash-slag based one-part alkali activated mortar10.1016/j.conbuildmat.2020.118533 ↗
24. 2009
25. C. ASTM, Standard test method for flow of hydraulic cement mortar.
26. Improving the mechanical properties of fly ash-based Geopolymer Composites with PVA Fiber and Powder10.3390/ma15072363 ↗
27. C. ASTM, Standard test method for density, absorption, and voids in hardened concrete.
28. C. ASTM, Compression test determine the compressive strength of hydraulic cement and other mortars.
29. C. ASTM, Determines the flexural strength of hydraulic-cement mortars.
30. Impact behavior and microstructural characteristics of PVA fiber reinforced fly ash-geopolymer boards prepared by extrusion technique10.1007/s10853-006-6293-5 ↗
31. C. ASTM, Standard test methods for chemical resistance of mortars, grouts, and monolithic surfacings and polymer concretes.
32. Bong · 2022
33. Effect of polypropylene fiber on properties of alkali-activated slag mortar
34. Fiber-reinforced geopolymer composites
35. Impact of fiber reinforcements on properties of geopolymer composites
36. Mechanical properties of hybrid fiber reinforced ternary-blended alkali-activated materials10.1016/j.conbuildmat.2022.129841 ↗
37. Fiber-reinforced alkali-activated concrete
38. A comprehensive study of the polypropylene fiber reinforced fly ash based geopolymer10.1371/journal.pone.0147546 ↗
39. Flexural behavior of geopolymer composites reinforced with steel and polypropylene macro fibers10.1016/j.cemconcomp.2016.11.014 ↗
40. The effect of fiber properties on high performance alkali-activated slag/silica fume mortars10.1016/j.compositesb.2012.09.080 ↗
41. Strength, durability and micro-structural assessment of slag-agro blended based alkali activated engineered geopolymer composites
42. Comparative study on the effect of fiber type and content on the performance of one-part alkali-activated mortar10.1016/j.conbuildmat.2020.118221 ↗
43. A state of the art on effect of alkali activator, precursor, and fibers on properties of geopolymer composites
44. Rheological and mechanical properties of fiber-reinforced alkali-activated composite10.1016/j.conbuildmat.2015.07.182 ↗
45. Mix design and flexural toughness of PVA fiber reinforced fly ash-geopolymer composites10.1016/j.conbuildmat.2017.05.172 ↗
46. Effect of synthetic fibers on the properties of geopolymers based on non-heat treated phosphate mine tailing10.1016/j.matchemphys.2020.124147 ↗
47. Mechanical properties of MK-based geopolymer composites reinforced with PVA and PET fibers
48. Drying shrinkage in alkali-activated binders–a critical review10.1016/j.conbuildmat.2018.09.125 ↗
49. Experimental and numerical investigations on the flexural performance of geopolymers reinforced with short hybrid polymeric fibres10.1016/j.compositesb.2017.06.001 ↗
50. Durability of the reinforced one-Part Alkali-activated slag mortars with different fibers10.1007/s12649-020-00958-x ↗
51. High strength fiber reinforced one-part alkali activated slag/fly ash binders with ceramic aggregates: microscopic analysis, mechanical properties, drying shrinkage, and freeze-thaw resistance10.1016/j.conbuildmat.2020.118129 ↗
52. Mechanical properties and durability of fiber reinforced alkali activated slag concrete10.1061/(ASCE)MT.1943-5533.0002073 ↗
53. Durability of the reinforced one-part alkali-activated slag mortars with different fibers10.1007/s12649-020-00958-x ↗
54. Durability of plant fiber reinforced alkali activated compositeS10.1016/j.conbuildmat.2021.125501 ↗
55. Characterisation of one-part geopolymer binders made from fly ash10.1007/s12649-016-9582-5 ↗
56. Effects of Portland cement on activation mechanism of class F fly ash geopolymer cured under ambient conditions10.1016/j.conbuildmat.2018.09.065 ↗
57. Compatibility studies between NASH and CASH gels. Study in the ternary diagram Na2O–CaO–Al2O3–SiO2–H2O10.1016/j.cemconres.2011.05.006 ↗
58. Development of greener alkali-activated cement: utilisation of sodium carbonate for activating slag and fly ash mixtures10.1016/j.jclepro.2015.12.010 ↗
59. Effect of synthesis parameters on compressive strength of fly ash-slag blended geopolymer10.1016/j.conbuildmat.2018.03.026 ↗