journal article·2023-09Open access

Interfacial microstructure, element diffusion, mechanical properties and metallurgical bonding mechanism of 316L-AlSi10Mg multi-material parts fabricated by laser powder bed fusion

Huan Miao, Farazila Yusof, Mohd Sayuti Ab Karim, Bo Wu, Sufian Raja, M.Z. Ibrahim, Izhar Aziz, Daolun Chen

Abstract

This work explored the interfacial microstructure, element diffusion, mechanical properties and metallurgical bonding mechanism of 316L-AlSi10Mg multi-material parts fabricated by laser powder bed fusion (LPBF). Experimental results revealed that insufficient volumetric energy density (VED) of the laser caused lack-fusion porosity in the 316L-AlSi10Mg transition zone, while too high VED produced keyhole-induced porosity defects. Using the optimal process parameters, multi-material parts can be produced with a good interface metallurgical bonding without significant defects. The partial Fe-FCC phase in 316L stainless steel changed into the Fe-BCC structure, and this shift has also changed the preferred orientation of the grains. The intermetallic compound Al5Fe2 and AlFe phases were found in the transition zone. In addition, Al-Fe icosahedral quasicrystals with five-fold symmetry were found at the boundary of the molten pool, which was caused by an extremely high cooling rate. The tensile strength of 316L-AlSi10Mg specimens is higher than that of AlSi10Mg but lower than that of 316L. In contrast to the 316L and AlSi10Mg regions, the fracture mechanism of multi-material fusion zone exhibits a quasi-cleavage fracture mode. The Vickers microhardness of the Al-Fe interface zone was higher than that of 316L with an average value of 235.57 HV0.2 and AlSi10Mg with 124.59 HV0.2, and the interfacial maximum hardness reached 526.68 HV0.2, which was caused by the very hard intermetallic compound Al5Fe2 and AlFe. The metallurgical bonding mechanism of multi-materials was that the dissimilar metals were mixed and in-situ alloyed in the molten pool by the Marangoni convection-induced strong circular flow during LPBF processing.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Effect of scanning speed and laser power on formability, microstructure, and quality of 316L stainless steel prepared by selective laser melting10.1016/j.jmrt.2023.06.144 ↗
2. Selective laser melting of Al–Si–10Mg alloy: microstructural studies and mechanical properties assessment10.1016/j.jmrt.2022.01.135 ↗
3. Feasibility study of thermo-compensated resistance brazing welding of 6061 aluminum alloy to 304 stainless steel10.1016/j.jmrt.2023.02.059 ↗
4. Challenges and latest developments in diffusion bonding of high-magnesium aluminium alloy (Al-5056/Al-5A06) to stainless steels10.3390/met12071193 ↗
5. Effect of friction stir welding on microstructure and mechanical properties of dissimilar Al 5083-H321 and 316L stainless steel alloy joints10.1016/j.jallcom.2016.03.307 ↗
6. Microstructure and high temperature tensile properties of 316L fabricated by laser powder-bed fusion
7. Comparatively evaluating the room and high temperature mechanical properties of AlSi10Mg alloy produced by selective laser melting10.1016/j.jmrt.2022.10.162 ↗
8. Evolution of the microstructure and multi-objective optimization of the tensile properties of GH3625 superalloy by selective laser melting10.1016/j.jmrt.2023.05.141 ↗
9. Graded Inconel-stainless steel multi-material structure by inter- and intralayer variation of metal alloys10.1016/j.jmrt.2022.11.064 ↗
10. Additive manufacturing of functionally graded metallic materials: a review of experimental and numerical studies10.1016/j.jmrt.2021.05.022 ↗
11. Effects of process parameters on interfacial characterization and mechanical properties of 316L/CuCrZr functionally graded material by selective laser melting10.1016/j.jallcom.2021.163256 ↗
12. Interfacial characterization of SLM parts in multi-material processing: metallurgical diffusion between 316L stainless steel and C18400 copper alloy10.1016/j.matchar.2014.05.001 ↗
13. Interfacial characterization of SLM parts in multi-material processing: intermetallic phase formation between AlSi10Mg and C18400 copper alloy10.1016/j.matchar.2015.07.007 ↗
14. Influence mechanism of process parameters on the interfacial characterization of selective laser melting 316L/CuSn10
15. Dual interfacial characterization and property in multi-material selective laser melting of 316L stainless steel and C52400 copper alloy10.1016/j.matchar.2020.110489 ↗
16. Additive manufacturing of horizontal and 3D functionally graded 316L/Cu10Sn components via multiple material selective laser melting10.1115/1.4043983 ↗
17. 3D printing of multiple metallic materials via modified selective laser melting10.1016/j.cirp.2018.04.096 ↗
18. Development of processing strategies for multigraded selective laser melting of Ti6Al4V and IN71810.1016/j.powtec.2020.04.010 ↗
19. Interfacial characteristic and mechanical performance of maraging steel-copper functional bimetal produced by selective laser melting based hybrid manufacture10.1016/j.matdes.2018.05.064 ↗
20. The effect of scanning strategy on laser fusion of functionally graded H13/Cu materials10.1007/s00170-005-0130-x ↗
21. Additive manufacturing of three-dimensional metal-glass functionally gradient material components by laser powder bed fusion with in situ powder mixing
22. Cu10Sn to Ti6Al4V bonding mechanisms in laser-based powder bed fusion multiple material additive manufacturing with different build strategies
23. A study of the microstructural evolution during selective laser melting of Ti–6Al–4V10.1016/j.actamat.2010.02.004 ↗
24. Critical instability at moving keyhole tip generates porosity in laser melting10.1126/science.abd1587 ↗
25. Numerical simulation of laser ultrasonic detection of the surface microdefects on laser powder bed fusion additive manufactured 316L stainless steel10.1016/j.taml.2022.100398 ↗
26. Evaluating the coefficient of thermal expansion of additive manufactured AlSi10Mg using microwave techniques
27. Enhanced tensile ductility of an additively manufactured AlSi10Mg alloy by reducing the density of melt pool boundaries10.1016/j.scriptamat.2022.114954 ↗
28. Gradient in microstructure and mechanical property of selective laser melted AlSi10Mg10.1016/j.jallcom.2017.11.020 ↗
29. Metalic phase with long-range orientational order and No translational symmetry10.1103/PhysRevLett.53.1951 ↗
30. Unveiling damage sites and fracture path in laser powder bed fusion AlSi10Mg: comparison between horizontal and vertical loading directions10.1016/j.msea.2021.140845 ↗
31. Hybrid additive manufacture of 316L stainless steel with cold spray and selective laser melting: microstructure and mechanical properties10.1016/j.jmatprotec.2019.05.029 ↗
32. Comparative analysis and experimental validation of statistical and machine learning-based regressors for modeling the surface roughness and mechanical properties of 316L stainless steel specimens produced by selective laser melting10.1016/j.jmapro.2022.06.021 ↗
33. Surface quality and material removal in magnetic abrasive finishing of selective laser melted 316L stainless steel10.1016/j.jmapro.2019.07.044 ↗
34. Microstructure and mechanical properties of CNC-SLM hybrid manufacturing 316L parts10.1016/j.jmapro.2022.04.053 ↗
35. Effect of deep cryogenic treatment on mechanical properties and residual stress of AlSi10Mg alloy fabricated by laser powder bed fusion10.1016/j.jmatprotec.2022.117543 ↗
36. Individual and synergistic effects of thermal and mechanical surface post-treatments on wear and corrosion behavior of laser powder bed fusion AlSi10Mg10.1016/j.jmatprotec.2021.117479 ↗
37. Investigation for macro mechanical behavior explicitly for thin-walled parts of AlSi10Mg alloy using selective laser melting technique10.1016/j.jmapro.2021.04.022 ↗
38. An optimal fuzzy decision-making approach for laser powder bed fusion of AlSi10Mg alloy10.1016/j.jmapro.2020.08.054 ↗
39. Pulsed SLM-manufactured AlSi10Mg alloy: mechanical properties and microstructural effects of designed laser energy densities10.1016/j.jmapro.2018.09.007 ↗
40. Comparative study on NiAl and FeAl intermetallic-bonded diamond tools and grinding performance for Si3N4 ceramic10.1016/j.ceramint.2021.08.170 ↗
41. Fabrication and microstructure characterization of selective laser-melted FeAl intermetallic parts10.1016/j.surfcoat.2012.05.072 ↗
42. Effects of sulfur concentration and Marangoni convection on melt-pool formation in transition mode of selective laser melting process10.1016/j.matdes.2019.107866 ↗
43. Correlation between forming quality and spatter dynamics in laser powder bed fusion
44. Quantitative characterization of porosity in laser welds of stainless steel10.1016/j.scriptamat.2012.06.015 ↗
45. Formation of metastable cellular microstructures in selective laser melted alloys10.1016/j.jallcom.2016.12.209 ↗
46. Laser powder bed fusion of a novel high strength quasicrystalline Al–Fe–Cr reinforced Al matrix composite