journal article·2024-03Open access

Influence of Cu/Mg ratio and content on heat-resistance of Al–Cu–Mg alloys

Huabing Yang, Yunteng Liu, Ying Li, Suqing Zhang, Jianhua Wu, Huan Yu, Hongtao Liu, Baichang Ma, Haihua Zhuang, Xuansheng Feng, Peng Zhang, Jixue Zhou, Xiangfa Liu

Abstract

Heat-resistant Al alloys used in such as aerospace, transportation fields are attracting more and more attention in recent years. Within Al alloy families, Al–Cu–Mg alloys have shown promising heat resistance properties. This work aims to investigate the influence of Cu/Mg ratio and content on the heat resistance of Al–Cu–Mg alloys, based on alloys of Al–4.5Cu–2.5 Mg (referred to as alloy A), Al–4.0Cu–2.2 Mg (alloy B) and Al–4.5Cu–1.6 Mg (alloy C). The alloys A and B possessed approximate Cu/Mg ratio, and they also exhibited nearly identical hardness retention rate during exposure at 200 °C. After 200 h, the rate is ∼75 %, though alloy A showed higher hardness (105 vs. 102 HBW) due to higher Cu, Mg content. In contrast, alloy C with a higher Cu/Mg ratio was less heat-resistant, with hardness retention rate of ∼70.5 % after 200 h exposure. Nano-sized S′(Al2CuMg) precipitate was main strengthening phase for the three alloys. Also, micron and submicron Al2CuMg particles could be formed with increase of Cu and Mg contents, which contributed a lot to yield strength for T6 heat-treated alloys, but slight contribution after exposure at 200 °C for 200 h. The degradation of mechanical properties during heat exposure can be attributed to the transformation and coarsening of S′ precipitates. In alloys with lower Cu/Mg ratio, there was excess Mg dissolved in Al matrix, which reduced Cu solubility in α-Al, and then slowed diffusion flux of Cu element, thus inhibited coarsening of Al2CuMg phase.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. Precipitation strengthening of aluminum alloys by room-temperature cyclic plasticity10.1126/science.aav7086 ↗
2. Artifact-free bulk nanocrystalline Al-Li alloys with multiple deformation mechanisms and improved tensile properties
3. Modeling of residual stress evolution of 7050 aluminium alloy component during heat treatment and cold forming
4. A novel Al matrix composite reinforced by nano-AlNp network
5. Three-dimensional rigid multiphase networks providing high-temperature strength to cast AlSi10Cu5Ni1-2 piston alloys10.1016/j.actamat.2011.07.006 ↗
6. Mechanical properties of unidirectionally solidified Al-Si eutectic alloys10.1179/030634575790444874 ↗
7. Creep behaviour of unreinforced and short fibre reinforced AlSi12CuMgNi piston alloy10.1016/j.msea.2006.01.024 ↗
8. The effects of temperature and strain rate on the properties of carbon-fiber-reinforced 7075 aluminum alloy metal-matrix composite10.1016/S0266-3538(00)00083-X ↗
9. A novel heat-resistant Al–Si–Cu–Ni–Mg base material synergistically strengthened by Ni-rich intermetallics and nano-AlNp microskeletons10.1016/j.jmst.2018.09.051 ↗
10. High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB2 particles10.1016/j.msea.2015.03.021 ↗
11. High-temperature mechanical properties of 2024 Al matrix nanocomposite reinforced by TiC network architecture10.1016/j.msea.2019.138121 ↗
12. Ultrasonic-assisted synthesis of surface-clean TiB2 nanoparticles and their improved dispersion and capture in Al-matrix nanocomposites10.1021/am402719p ↗
13. Microstructure and high temperature stability of age hardenable AA2219 aluminium alloy modified by Sc, Mg and Zr additions10.1016/j.msea.2007.01.144 ↗
14. Determination of Er and Yb solvuses and trialuminide nucleation in Al–Er and Al–Yb alloys10.1016/j.jallcom.2013.11.211 ↗
15. Precipitation strengthening at ambient and elevated temperatures of heat-treatable Al(Sc) alloys10.1016/S1359-6454(02)00201-X ↗
16. Effects of Mo and Mn microadditions on strengthening and over-aging resistance of nanoprecipitation-strengthened Al-Zr-Sc-Er-Si alloys10.1016/j.actamat.2018.11.031 ↗
17. The solubility of certain transition metals in aluminium10.1007/BF00811665 ↗
18. Microstructural evolution and mechanical property of Al–Zr and Al–Zr–Y alloys10.1016/j.msea.2014.08.017 ↗
19. Precipitation hardening in the first aerospace aluminum alloy: the Wright flyer crankcase10.1126/science.266.5187.1015 ↗
20. Effects of Ag variations on the microstructures and mechanical properties of Al–Cu–Mg alloys at elevated temperatures10.1016/j.msea.2014.05.065 ↗
21. Effect of aging temper on the thermal stability of Al–Cu–Mg–Ag heat-resistant alloy10.1016/j.matdes.2012.10.039 ↗
22. On the origin of the high coarsening resistance of Ω plates in Al-Cu-Mg-Ag alloys10.1016/S1359-6454(01)00155-0 ↗
23. Effect of Sc addition on the microstructures and age-hardening behavior of an Al–Cu–Mg–Ag alloy10.1016/j.msea.2019.04.045 ↗
24. Design and development of an experimental wrought aluminum alloy for use at elevated temperatures10.1007/BF02628387 ↗
25. Effects of Yb addition on microstructures and mechanical properties of 2519A aluminum alloy plate10.1016/S1003-6326(09)60205-3 ↗
26. Alloying effect of Mg on microstructure and mechanical properties at 300°C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy10.1088/2053-1591/ac1d67 ↗
27. Structure and properties of new heat-resistant cast alloys based on the Al–Cu–Y and Al–Cu–Er systems10.1134/S0031918X21090027 ↗
28. Precipitating thermally reinforcement phase in aluminum alloys for enhanced strength at 400°C10.1016/j.jmst.2023.06.038 ↗
29. Thermal stability of Al-Cu-Mg alloys10.4028/www.scientific.net/MSF.794-796.691 ↗
30. Morphologies, orientation relationships, and evolution of the T-phase in an Al-Cu-Mg-Mn alloy during homogenization10.1016/j.jallcom.2017.03.161 ↗
31. Precipitation processes and structural evolutions of various GPB zones and two types of S phases in a cold-rolled Al-Mg-Cu alloy10.1016/j.matdes.2020.109425 ↗
32. The crystallography and morphology of the S'-phase precipitate in an Al (CuMg) alloy10.1080/01418618708209875 ↗
33. Precipitation hardening of an Al–4.2 wt% Mg–0.6 wt% Cu alloy10.1016/S1359-6454(98)00033-0 ↗
34. Precipitates and intermetallic phases in precipitation hardening Al–Cu–Mg–(Li) based alloys10.1179/174328005X14357 ↗
35. Origins of hardening in aged Al–Cu–Mg–(Ag) alloys10.1016/S1359-6454(97)00039-6 ↗
36. Microstructural evolution and age hardening in aluminium alloys: atom probe field-ion microscopy and transmission electron microscopy studies10.1016/S1044-5803(99)00051-0 ↗
37. Effects of Ti additions on the nanostructure and creep properties of precipitation-strengthened Al–Sc alloys10.1016/j.actamat.2005.05.022 ↗
38. Effects of Ti additions on the nanostructure and creep properties of precipitation-strengthened Al–Sc alloys10.1016/j.actamat.2005.05.022 ↗
39. Identification of novel dual-scale Al3BC particles in Al based composites10.1016/j.matdes.2015.12.104 ↗
40. The influence of particle size and particle fracture on the elastic/plastic deformation of metal matrix composites10.1016/1359-6454(96)00008-0 ↗
41. Enhanced creep performance in an Al–Cu–Mg–Ag alloy through underageing10.1016/S1359-6454(02)00164-7 ↗
42. Porter · 2009 · 310
43. The effect of long-term thermal exposures on the microstructure and properties of CMSX-10 single crystal Ni-base superalloys10.1016/j.msea.2004.04.001 ↗
44. Artificial ageing of Al–Mg–Cu alloys10.2320/matertrans1989.40.34 ↗