journal article·2024-07Open access

Enhancing high-speed EDM performance of hybrid aluminium matrix composite by genetic algorithm integrated neural network optimization

Muhammad Asad Ali, Nadeem Ahmad Mufti, Muhammad Sana, Mehdi Tlija, Muhammad Umar Farooq, Rodolfo Haber

Abstract

Hybrid aluminium matrix composites (HAMCs) are highly valued in manufacturing sectors but are difficult to machine conventionally due to reinforcements' inherent hardness and abrasiveness. This research finds high-speed wire electric discharge machining (WEDM) to be a potent solution for machining stir-squeeze-casted HAMC (AA2024 with ceramic nanoparticles: Al2O3, SiC, Si3N4, BN) and creating complex profiles with superior erosion characteristics. The erosion performance has been assessed in terms of material removal rate (MRR) for different profiles (plane, angular, and curve), and wire wear ratio (WWR) by employing machining variables, i.e., pulse voltage (PV), pulse current (PI), wire feed rate (WFR), pulse (P), and drum speed (DS). Results revealed that MRR_curve has highest MRR (37.84 mm3/min), followed by MRR_angular (36.07 mm3/min) and MRR_plane (34.40 mm3/min). The lowest WWR (0.0094%) was achieved at lower magnitudes of machining variables. The microscopic observations unveil shallow craters, minute-sized melt redeposits, and micro-pores on machined surface under the conditions of PV = 90 V, PI = 2 A, WFR = 13 m/min, P = 20 mu, and DS = 40 Hz. Optimization using non-dominated-sorting-genetic algorithm (NSGA-II) resulted in significant enhancements of 75.37, 73.90, and 76.01% in MRR_plane, MRR_angular, and MRR_curve, respectively, and a depreciation of 16.50% in WWR.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Machining and Optimization Techniques · Aluminum Alloys Composites Properties · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. Interfacial structure and properties of microwave sintered FeCoNi1.5CrCu/Al composites10.1016/j.matchar.2022.111993 ↗
2. Synthesis and wear behaviour analysis of SiC- and Rice husk ash-based aluminium metal matrix composites10.3390/jcs7090394 ↗
3. Opportunities and challenges in machining of aluminium metal matrix composites using electrical discharge machining
4. Tribological and corrosion characteristics of tetra hybrid particulate-reinforced aluminum composites for aerospace and automotive applications10.1177/00219983231210354 ↗
5. Microstructural, mechanical and machining studies of Al-4032 alloy based hybrid composite10.1007/s12633-022-02058-y ↗
6. Microstructure and properties of FeCoNiCrMn and Al2O3 hybrid particle-reinforced aluminum matrix composites fabricated by microwave sintering10.1016/j.jmrt.2023.05.100 ↗
7. Tribological analysis of squeeze stir cast recycled aluminum MMC's
8. Performance analysis of different dielectric on electrical discharge machined AA8011/SiC/Si3N4 composites using Taguchi coupled ELECTRE approach10.1007/s12633-023-02696-w ↗
9. Exploring the effects of ball milling and microwave sintering on microstructural and mechanical behavior of AA7075/SiC/ZrO2 hybrid composites10.1007/s12633-024-02856-6 ↗
10. Machinability analysis on wire electrical discharge machining of stir casted AA2024/Al 2 O 3/BN hybrid composite for aerospace applications10.1080/10426914.2020.1854466 ↗
11. Comprehensive study on tool wear during machining of fiber-reinforced polymeric composites
12. Study of correlation of machining performance and geometrical tolerances of Si3N4-TiN composites using EDM process10.1007/s12633-024-02884-2 ↗
13. WEDM process parameter optimization of FSPed copper-BN composites10.1080/10426914.2017.1339311 ↗
14. Curved profiles machining of Ti6Al4V alloy through WEDM: investigations on geometrical errors10.1016/j.jmrt.2020.11.067 ↗
15. Kumar · J Mater Res Technol · 2023 · 26 · 856910.1016/j.jmrt.2023.09.127 ↗
16. Analyzing the dimensional errors in wire electric discharge machining of squeeze casted Al2024/Al2O3/W composite using cryogenic treated electrodes10.1016/j.jmrt.2024.01.125 ↗
17. A novel flushing mechanism to minimize roughness and dimensional errors during wire electric discharge machining of complex profiles on inconel 71810.3390/ma15207330 ↗
18. Exploring wide-parametric range for tool electrode selection based on surface characterization and machining rate employing powder-mixed electric discharge machining process for Ti6Al4V ELI
19. A comprehensive investigation of geometrical accuracy errors during WEDM of Al6061-7.5%SiC composite10.1080/10426914.2020.1832683 ↗
20. Investigating the parametric effects on wire electric discharge machining performance in processing AA1050-5 wt.% SiC composite with zinc-coated brass wire10.1007/s40430-022-03427-9 ↗
21. Investigation of wear and wire electrical discharge machining characteristics of Al-Mg-MoS2 composites using response surface method10.1520/JTE20220327 ↗
22. Process parameters optimization and performance analysis of micro-complex geometry machining on Ti6Al4V10.1007/s12008-023-01711-z ↗
23. Multi-objective optimization using grey relational analysis for wire EDM of aluminium matrix composites10.1016/j.matpr.2022.09.415 ↗
24. Optimization of wire-EDM process parameters for Al-Mg-0.6Si-0.35Fe/15%RHA/5%Cu hybrid metal matrix composite using TOPSIS: processing and characterizations10.3390/jmmp6060150 ↗
25. Optimisation of wire EDM process parameters using Taguchi technique for machining of hybrid composites10.1504/IJMATEI.2022.125110 ↗
26. Energy optimization using silicon dioxide composite and analysis of wire electrical discharge machining characteristics
27. Optimization of wire EDM process parameters for machining hybrid composites using grey relational analysis10.3390/cryst13111549 ↗
28. Investigation on the performance of wire electrical discharge machining (WEDM) using aluminium matrix composites (AMCs) micro-channel10.1088/2631-8695/acf5ca ↗
29. Experimental investigation of MRR on in situ formed AA7075/TiB_{2 cast composites machining by wire EDM10.1504/IJMMM.2015.072001 ↗
30. Improvement on the wire EDM characteristics of zirconia filled Al7050 (Al-Zn-Cu-Mg) alloy composite using Taguchi coupled TOPSIS method
31. EVALUATION OF MATERIAL REMOVAL RATE AND SURFACE ROUGHNESS IN WIRE ELECTRO-DISCHARGE MACHINING OF 10-WT.% ZrO 2 -REINFORCED AL ALLOY COMPOSITE10.1142/S0218625X22500081 ↗
32. Networked sensing for high-speed machining processes based on CORBA10.1016/j.sna.2004.10.022 ↗
33. Cryogenic treatment analysis of electrodes in wire electric discharge machining of squeeze casted Al2024/Al2O3/W composite10.1007/s00170-021-07521-5 ↗
34. A modified approach on modeling-design-optimization procedure for cutting of pure titanium using wire electric discharge machining (WEDM)
35. Comprehensive review on wire electrical discharge machining: a non-traditional material removal process
36. WEDM of Mg/CRT/BN composites: effect of materials and machining parameters10.1080/10426914.2017.1279316 ↗
37. Coping with complexity when predicting surface roughness in milling processes: hybrid incremental model with optimal parametrization10.1155/2017/7317254 ↗
38. Ensemble of convolutional neural networks based on an evolutionary algorithm applied to an industrial welding process10.1016/j.compind.2021.103530 ↗
39. Computer vision system for welding inspection of liquefied petroleum gas pressure vessels based on combined digital image processing and deep learning techniques10.3390/s20164505 ↗
40. Predictive modelling framework on the basis of artificial neural network: a case of nano-powder mixed electric discharge machining10.1016/j.heliyon.2023.e22508 ↗
41. Machine learning for multi-dimensional performance optimization and predictive modelling of nanopowder-mixed electric discharge machining (EDM)10.1007/s00170-024-13023-x ↗
42. Predicting biodiesel properties and its optimal fatty acid profile via explainable machine learning10.1016/j.renene.2022.02.124 ↗
43. Sustainable electric discharge machining using alumina-mixed deionized water as dielectric: process modelling by artificial neural networks underpinning net-zero from industry10.1016/j.jclepro.2024.140926 ↗