journal article·2022-05Open access

Effect of Cu and solid solution temperature on microstructure and mechanical properties of Fe-Mn-Al-C low-density steels

Zhiqi Xie, Weijun Hui, Yongjian Zhang, Xiaoli Zhao

Abstract

Relatively low yield strength (YS) level restricts austenitic low-density steels to some applications requiring small or no deformation than impact energy absorption. Therefore, to enhance the YS of this type of steel, this research investigates variations of microstructure and mechanical properties of two austenitic low-density steels (Fe-25Mn-10Al-1.1C-(0,0.25) Cu) with solid solution temperatures (TS, 850 °C–1050 °C). The results show that TS and Cu have significant impacts on the microstructure characteristics and mechanical properties of the two tested steels. At low TS of 850 °C, an increase of 170 MPa in YS compared with that of Cu-free steel was obtained in Cu-containing steel, which is mainly attributed to much finer grain size, more fine twins, and high dislocation density of the latter. An increase in TS caused the κ-carbides in the two steels to dissolve completely, but the austenite content in Cu-containing steel remained largely stable for the addition of Cu. As a result, the strength of the two tested steels decreased while the ductility increased, and both the strength and yield-to-tensile strength ratio of Cu-containing steel are remarkably higher than those of Cu-free steel. It is concluded that the Cu-containing steel exhibits a superior combination of YS and ductility together with a ∼17% reduction in density compared to pure iron. This study provides a promising way to further enhance the YS of austenitic low-density steels through the addition of a small amount of Cu and tailoring TS.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. Current state of Fe–Mn–Al–C low density steels10.1016/j.pmatsci.2017.05.002 ↗
2. Research progress of ordered precipitates in low–density steels
3. Low density Fe–Mn–Al–C steels: phase structures, mechanisms and properties10.2355/isijinternational.ISIJINT-2020-467 ↗
4. Excellent combination of strength and ductility in an Fe–9Al–28Mn–1.8C alloy10.1016/j.scriptamat.2010.03.038 ↗
5. Control of inter/intra–granular κ–carbides and its influence on overall mechanical properties of a Fe–11Mn–10Al–1.25C low density steel10.1016/j.msea.2017.12.102 ↗
6. Simulation of κ–carbide precipitation kinetics in aged low–density Fe–Mn–Al–C steels and its effects on strengthening10.1007/s12540-018-0089-4 ↗
7. Microstructural change in austenitic Fe–30.0wt%Mn–7.8wt%Al–1.3wt%C initiated by spinodal decomposition and its influence on mechanical properties10.1016/S1359-6454(97)00201-2 ↗
8. The effect of Mn and Al contents on the solvus of κ phase in austenitic Fe–Mn–Al–C alloys10.1016/S0254-0584(99)00026-7 ↗
9. Effect of annealing temperature on microstructural modification and tensile properties in 0.35C–3.5Mn–5.8Al lightweight steel
10. Effect of austenite stability on microstructural evolution and tensile properties in intercritically annealed medium–Mn lightweight steels10.1007/s11661-016-3433-7 ↗
11. Hot deformation behavior of an industrially cast large grained low density austenitic steel10.1016/j.msea.2021.141785 ↗
12. Chemical composition optimization for austenitic steels of the Fe–Mn–Al–C system10.1361/105994900770345430 ↗
13. Development of thermodynamic database for high Mn–high Al steels: phase equilibria in the Fe–Mn–Al–C system by experiment and thermodynamic modeling10.1016/j.calphad.2015.08.004 ↗
14. Effect of aging on the microstructure and deformation behavior of austenite base lightweight Fe–28Mn–9Al–0.8C steel10.1016/j.scriptamat.2010.07.036 ↗
15. Deformation mechanisms in ultrahigh–strength and high–ductility nanostructured FeMnAlC alloy10.1016/j.jallcom.2013.10.153 ↗
16. Tensile deformation of a low density Fe–27Mn–12Al–0.8C duplex steel in association with ordered phases at ambient temperature10.1016/j.msea.2013.07.094 ↗
17. Evolution of the microstructure and mechanical properties of an austenite–ferrite Fe–Mn–Al–C steel10.1016/j.msea.2015.07.043 ↗
18. Phase transitions in an Fe–9Al–30Mn–2.0C alloy10.1016/j.scriptamat.2007.07.007 ↗
19. Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys10.1016/j.msea.2004.01.059 ↗
20. Microband–induced plasticity in a high Mn–Al–C light steel10.1016/j.msea.2008.05.042 ↗
21. Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight–reduced Fe–Mn–Al–C steel10.1016/j.actamat.2012.07.018 ↗
22. Strain hardening behavior of aluminum alloyed Hadfield steel single crystals10.1016/j.actamat.2004.12.033 ↗
23. Brittle intermetallic compound makes ultrastrong low–density steel with large ductility10.1038/nature14144 ↗
24. Novel ultra–high–strength (ferrite+austenite) duplex lightweight steels achieved by fine dislocation substructures (Taylor lattices). grain refinement, and partial recrystallization10.1016/j.actamat.2015.06.024 ↗
25. Effect of tempering temperatures on the mechanical properties and microstructures of HSLA–100 type copper–bearing steels10.1016/S0921-5093(01)01259-X ↗
26. Novel ultra–high–strength Cu–containing medium–Mn duplex lightweight steels10.1016/j.actamat.2017.06.035 ↗
27. Suppression of surface hot shortness caused by copper during hot rolling10.4028/www.scientific.net/MSF.696.183 ↗
28. Evaluation of the density of steels
29. On the eutectoid reaction in a quaternary Fe–C–Mn–Al alloy: austenite → ferrite + kappa–carbide + M23C6 carbide10.1007/s11661-013-2083-2 ↗
30. Improvement of tensile properties in (austenite+ferrite+κ–carbide) triplex hot–rolled lightweight steels10.1016/j.msea.2018.06.003 ↗
31. Tensile deformation of low–density Fe–Mn–Al–C austenitic steels at ambient temperature10.1016/j.scriptamat.2012.09.031 ↗
32. Derivation and variation in composition–dependent stacking fault energy maps based on subregular solution model in high–manganese steels10.1007/s11661-009-0050-8 ↗
33. Influence of Al content and precipitation state on the mechanical behavior of austenitic high–Mn low–density steels10.1016/j.scriptamat.2012.08.038 ↗
34. Thermal stability of retained austenite in TRIP steels studied by synchrotron X–ray diffraction during cooling10.1016/j.actamat.2005.08.017 ↗
35. An investigation to the microstructural evolution of Fe–29Mn–5Al dual–phase twinning–induced plasticity steel through annealing10.1016/j.matdes.2011.06.004 ↗
36. Effects of ferrite volume fraction on the tensile deformation characteristics of dual phase twinning induced plasticity steel10.1016/j.matdes.2013.06.033 ↗
37. Study of annealing twins in FCC metals and alloys10.1007/BF02647209 ↗
38. The effect of vanadium micro–alloying on the microstructure and the tensile behavior of TWIP steel10.1016/j.msea.2017.04.083 ↗
39. In–situ observations of lattice parameter fluctuations in austenite and transformation to bainite10.1007/s11661-005-0002-x ↗
40. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
41. Yong · 2006
42. Comparison of the dislocation density in martensitic steels evaluated by some X–ray diffraction methods10.2355/isijinternational.50.875 ↗
43. Estimating grain–size distributions in nanocrystalline materials from X–ray diffraction profile analysis10.1080/01418619808224072 ↗
44. On the deformation behavior of κ–carbide–free and κ–carbide containing high–Mn light–weight steel10.1016/j.actamat.2016.10.006 ↗
45. Strain hardening by dynamic slip band refinement in a high–Mn lightweight steel10.1016/j.actamat.2016.06.037 ↗
46. Origin of extended tensile ductility of a Fe–28Mn–10Al–1C steel10.1007/s11661-009-9862-9 ↗
47. Microstructural evolution and strain hardening behavior during plastic deformation of Fe–12Mn–8Al–0.8C steel10.1016/j.msea.2013.07.023 ↗
48. Effects of rolling temperature on the microstructure and mechanical properties of Ti–Mo microalloyed hot–rolled high strength steel10.1016/j.msea.2014.03.054 ↗
49. Combined κ–carbide precipitation and recovery enables ultra–high strength and ductility in light–weight steels10.1016/j.msea.2020.139928 ↗
50. Solute–dislocation interactions and creep–enhanced Cu precipitation in a novel ferritic–martensitic steel10.1016/j.actamat.2020.05.054 ↗
51. Nanoscale study of cyclic deformation behaviour and mechanism of annealing twin10.1016/j.msea.2006.04.098 ↗
52. Effects of Mn contents on the microstructure and mechanical properties of the Fe–10Al–xMn–1.0C alloy10.2320/matertrans.43.2635 ↗
53. Tensile deformation of a duplex Fe–20Mn–9Al–0.6C steel having the reduced pecific weight10.1016/j.msea.2011.03.045 ↗
54. Tensile deformation behavior of Fe–Mn–Al–C low density steels10.1016/S1006-706X(16)30145-5 ↗
55. Influence of Al content on the strain–hardening behavior of aged low density Fe–Mn–Al–C steels with high Al content10.1016/j.msea.2015.05.002 ↗
56. High–strength Fe–20Mn–Al–C based alloys with low density10.2355/isijinternational.50.893 ↗