journal article·2023-03Open access

Improvement of microstructure and mechanical properties of stainless steel TIG based wire arc additive manufacturing by using AC/DC mix current waveform

Chao Chen, Wenbo Du, Huijing Zhang, Xiaohui Zhao

Abstract

In this work, a new current waveform, the AC/DC mix current waveform was employed to improve the microstructure and mechanical properties of 307Si stainless steel component during the TIG based wire arc additive manufacturing (TIG-WAAM). The results showed that the morphology of γ-austenite is changed from the columnar dendrites (with DC mode) to the equiaxed dendrites (with AC/DC mix mode). The grain size was refined due to the reduction of the temperature gradient in the AC/DC mix mode. The degree of refinement grain is increased with the increase of AC ratio. The tensile strength of the 70%DC+30%AC-sample in the traveling and building directions are respectively increased by about 60 MPa and 41 MPa compared with that of the 100%DC-sample. The grain refinement is the mainly reason of the improvement of mechanical properties of the TIG-WAAM component with the AC/DC mix mode.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Structural design of high-strength austenitic stainless steel10.1016/j.tws.2006.04.014 ↗
2. Wire arc additive manufacturing of stainless steels: a review10.3390/app10051563 ↗
3. Microstructure and mechanical behavior of PH 13–8Mo martensitic stainless steel fabricated by wire arc additive manufacturing
4. Microstructural evolution in a thin wall of 2Cr13 martensitic stainless steel during wire arc additive manufacturing10.1016/j.matchar.2021.111520 ↗
5. Forming appearance analysis of 2205 duplex stainless steel fabricated by cold metal transfer (CMT) based wire and arc additive manufacture (WAAM) process
6. Modeling for GMAW process with a current waveform control method10.1016/j.jmatprotec.2016.10.018 ↗
7. A novel sine wave modulation method of pulse current during double wire MIG welding10.1007/s00170-016-9637-6 ↗
8. Study of steel-aluminium joining under the influence of current waveforms using advanced CMT process variants
9. A new approach to control centerline macrosegregation in Al-Mg-Si alloys during twin roll continuous casting10.1016/j.matlet.2016.12.109 ↗
10. Transient coupling simulation of multi-physical field during pulse electromagnetic direct-chill casting of AZ80 magnesium alloy10.1016/j.ijheatmasstransfer.2019.118524 ↗
11. Arc stability and its impact on weld properties and microstructure in anti-phase synchronised synergic-pulsed twin-wire gas metal arc welding10.1016/j.matdes.2014.11.052 ↗
12. Prediction and optimization of pulsed current gas tungsten arc welding process parameters to obtain sound weld pool geometry in titanium alloy using lexicographic method10.1007/s11665-008-9305-6 ↗
13. Achieving equiaxed microstructure and isotropic mechanical properties of additively manufactured az31 magnesium alloy via ultrasonic frequency pulsed arc10.1016/j.jallcom.2022.164742 ↗
14. Grain refinement of wire arc additive manufactured titanium alloy by the combined method of boron addition and low frequency pulse arc10.1016/j.msea.2020.140557 ↗
15. Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel[J]10.1016/j.msea.2019.02.078 ↗
16. Study on the weld formation, microstructure and mechanical properties of AZ31B Mg alloy in AC/DC mixed gas tungsten arc welding process10.1016/j.jmrt.2022.04.065 ↗
17. Mechanical properties and microstructural characteristics of wire arc additive manufactured 308L stainless steel cylindrical components made by gas metal arc and cold metal transfer arc welding processes10.1016/j.jmatprotec.2022.117655 ↗
18. Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing10.1016/j.msea.2017.05.024 ↗
19. Ultrasonic effects on gas tungsten arc based wire additive manufacturing of aluminum matrix nanocomposite10.1016/j.matdes.2022.110393 ↗
20. Improving mechanical properties of austenitic stainless steel by the grain refinement in wire and arc additive manufacturing assisted with ultrasonic impact treatment10.1016/j.msea.2022.144044 ↗
21. Review on effect of heat input for wire arc additive manufacturing process10.1016/j.jmrt.2021.02.002 ↗
22. Enhanced strength-ductility synergy of bimetallic laminated steel structure of 304 stainless steel and low-carbon steel fabricated by wire and arc additive manufacturing10.1016/j.msea.2022.143984 ↗
23. The dislocation behaviour and GND development in a nickel based superalloy during creep10.1016/j.ijplas.2019.02.015 ↗
24. Microstructure and mechanical properties of 2A12 aluminum alloy welded joint through CMT double side welding10.1016/j.cirpj.2022.02.006 ↗
25. Effect of heat treatment temperature on microstructure and tensile properties of austenitic stainless 316L using wire and arc additive manufacturing10.1016/j.msea.2021.142446 ↗
26. Effect of heat input on microstructure and mechanical properties of Al-Mg alloys fabricated by WAAM10.1016/j.apsusc.2019.04.255 ↗
27. Kou · 2002
28. Wire arc additive manufacturing of AZ31 magnesium alloy: grain refinement by adjusting pulse frequency10.3390/ma9100823 ↗
29. Microstructure characterization of SS308LSi components manufactured by GTAW-based additive manufacturing: shaped metal deposition using pulsed current arc10.1007/s00170-016-9053-y ↗