Thermal deformation behavior of Mg–3Sn–1Mn alloy based on constitutive relation model and artificial neural network
Source abstract
Abstract
The flow stress behavior of Mg–3Sn–1Mn alloy during thermal compression deformation was systematically studied. The thermal compression simulation experiment was carried out at different deformation temperatures and different strain rates in the range of 523–673 K and 0.001-1s−1, respectively. It is found that at low temperatures and high strain rates, a large number of twins were generated at the initial stage of thermal deformation, causing an increase in the corresponding flow stress, which makes the traditional constitutive relation model insensitive to predicting the thermal deformation behavior of Magnesium (Mg) alloys with twinning effect. To better evaluate the rheological behavior of Mg alloys, an artificial neural network (ANN) model based on a feedforward and back-propagation algorithm was developed to predict the thermal deformation behavior of Mg–3Sn–1Mn alloy affected by twinning phenomena. The inputs of the model were deformation temperature, strain rate and strain, the output was the flow stress. The comparative evaluation of the obtained results using statistical standard R2 and relative error R¯. The correlation coefficients predicted by the constitutive model were 0.964 and 0.869 at low and high stress levels, respectively. And the correlation coefficient of the neural network predictive model was 0.992. The result shows that the trained ANN is more accurate than the traditional constitutive relation model in predicting the thermal deformation behavior with the twinning effect.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. Investigating the temperature dependency of plastic deformation in a Mg-3Al-1Zn alloy10.1016/j.msea.2018.04.019 ↗
2. Microstructural evolution of pure magnesium under high strain rate loading10.1016/j.actamat.2014.12.030 ↗
3. Twinning and the ductility of magnesium alloys: Part I: “Tension” twins10.1016/j.msea.2006.12.037 ↗
4. Twinning and the ductility of magnesium alloys: Part II10.1016/j.msea.2007.02.109 ↗
5. Influence of {10-12} extension twinning on the flow behavior of AZ31 Mg alloy10.1016/j.msea.2006.09.069 ↗
6. Twinning-induced dynamic recrystallization in a magnesium alloy extruded at 450°C10.1016/j.scriptamat.2011.07.046 ↗
7. Twinning, dynamic recovery and recrystallization in hot worked Mg–Al–Zn alloy10.1016/S0921-5093(02)00007-2 ↗
8. Deformation twinning in rolled WE43-T5 rare earth magnesium alloy: influence on strain hardening and texture evolution10.1016/j.actamat.2017.03.075 ↗
9. Rollett · 2017
10. Ex-situ EBSD analysis of hot deformation behavior and microstructural evolution of Mg–1Al–6Y alloy via uniaxial compression10.1016/j.msea.2020.138978 ↗
11. Identification and analysis of anomalous {10 1 2} twins in an extruded Mg-2wt%Y alloy sheet during uniaxial tensile loading10.1016/j.msea.2020.139699 ↗
12. Hot deformation behavior, processing map, microstructure evolution and dynamic recrystallization mechanism of Mg-5Al-0.6Sc alloy10.1016/j.jallcom.2022.166244 ↗
13. Effect of circumferential strain rate on dynamic recrystallization and texture of Mg-13Gd-4Y-2Zn-0.5Zr alloy during rotary backward extrusion10.1016/j.jma.2019.12.012 ↗
14. Microstructure and texture evolution during compression-extrusion process for tension/compression symmetrical ZK61 magnesium alloy rod
15. Softening and dynamic recrystallization in magnesium single crystals during c-axis compression10.1016/j.actamat.2011.10.013 ↗
16. Deformation behavior of Mg-13Gd-4Y-2Zn-0.5Zr alloy on the basis of LPSO kinking, dynamic recrystallization and twinning during compression-torsion10.1016/j.matchar.2021.111215 ↗
17. Microstructural characteristics and mechanical properties of the hot extruded Mg-Zn-Y-Nd alloys10.1016/j.jmst.2020.05.021 ↗
18. Effect of Sn addition on the deformation behavior and microstructural evolution of Mg-Gd-Y-Zr alloy during hot compression10.1016/j.msea.2021.142026 ↗
19. Dislocation creep behavior in Mg–Al–Zn alloys10.1016/j.msea.2005.06.059 ↗
20. Hot deformation behavior and processing map development of AZ110 alloy with and without addition of La-rich Mish Metal10.1016/j.jmst.2020.04.064 ↗
21. Hot deformation behaviors of AZ91 magnesium alloy: constitutive equation, ANN-based prediction, processing map and microstructure evolution10.1016/j.jallcom.2022.164580 ↗
22. Hot deformation behavior of an extruded AZ31 alloy doped with rare-earth elements10.1016/j.jallcom.2020.156961 ↗
23. The prediction of hot flow behavior of Al–6%Mg alloy10.1016/j.mechrescom.2008.06.011 ↗
24. Strain-hardening and recovery during the creep of pure polycrystalline magnesium10.1016/0956-7151(94)90282-8 ↗
25. On the evolution and modelling of brass-type texture in cold-rolled twinning-induced plasticity steel10.1016/j.actamat.2014.02.033 ↗
26. Modeling of hot deformation behavior and prediction of flow stress in a magnesium alloy using constitutive equation and artificial neural network (ANN) model10.1016/j.jma.2018.05.002 ↗
27. Dynamic softening mechanisms and Zener-Hollomon parameter of Al–Mg–Si–Ce–B alloy during hot deformation10.1016/j.jmrt.2021.11.081 ↗
28. Effect of the Zener-Hollomon parameter on the dynamic recrystallization kinetics of Mg–Zn–Zr–Yb magnesium alloy10.1016/j.commatsci.2019.05.015 ↗
29. Effect of Zener–Hollomon parameter on hot deformation behavior of CoCrFeMnNiC high entropy alloy0.510.1016/j.msea.2019.138483 ↗
30. Dynamic behavior of extruded AZ61 Mg alloy during hot compression10.1016/j.msea.2011.12.043 ↗
31. Dislocation creep behavior in Mg–Al–Zn alloys10.1016/j.msea.2005.06.059 ↗
32. Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK6010.1016/S1359-6454(01)00020-9 ↗
33. Microtexture evolution via deformation twinning and slip during compression of magnesium alloy AZ3110.1016/j.msea.2006.07.175 ↗
34. Mechanical properties of copper/bronze laminates: role of interfaces10.1016/j.actamat.2016.06.023 ↗
35. Using neural networks to predict parameters in the hot working of aluminum alloys10.1016/S0924-0136(98)00318-5 ↗
36. Prediction of the flow stress of high-speed steel during hot deformation using a BP artificial neural network10.1016/S0924-0136(99)00444-6 ↗
37. Application of neural network and FEM for metal forming processes10.1016/S0890-6955(99)00090-5 ↗
38. Flow curve prediction of an Al-MMC under hot working conditions using neural networks10.1016/j.commatsci.2006.05.002 ↗
39. Flow behavior of Al–6.2Zn–0.70Mg–0.30Mn–0.17Zr alloy during hot compressive deformation based on Arrhenius and ANN models10.1016/S1003-6326(17)60071-2 ↗
40. Flow curve prediction of Al–Mg alloys under warm forming conditions at various strain rates by ANN10.1016/j.asoc.2010.06.004 ↗
41. Prediction of contact fatigue life of alloy cast steel rolls using back-propagation neural network10.1007/s11665-013-0695-8 ↗
42. Artificial neural network modeling to predict the high temperature flow behavior of an AZ81 magnesium alloy10.1016/j.matdes.2012.03.002 ↗
43. The applicability of neural network model to predict low stress for carbon steels10.1016/S0924-0136(02)01123-8 ↗
44. Artificial neural network modeling to evaluate and predict the deformation behavior of stainless steel type AISI 304L during hot torsion10.1016/j.asoc.2008.03.016 ↗
45. Mechanical properties prediction of composite laminate with FEA and machine learning coupled method10.1016/j.compstruct.2022.116086 ↗