journal article·2023-03Open access

Influence of expulsion and heat extraction resulting from changes to electrode force on liquid metal embrittlement during resistance spot welding

S. Song, M. Shojaee, A.R.H. Midawi, O. Sherepenko, Hassan Ghassemi-Armaki, E. Biro

Abstract

Zinc coatings are generally utilized for manufacturing corrosion-resistant advanced high-strength steels (AHSS). However, in new third generation AHSS (3G-AHSS), zinc from the coating may interact with the steel substrate leading to liquid metal embrittlement (LME) cracking during resistance spot welding (RSW). A critical RSW parameter that influences the LME response of the utilized 3G-AHSS is the electrode force. This study showed that the influence of electrode force on LME depended on whether or not welds experienced expulsion. When welding with low heat input, without expulsion, LME cracking severity decreased as electrode force increased. In such cases, increased force aided with heat extraction during welding, relieving the critical stresses required by LME cracking. In contrast, when welding with high heat input, resulting in expulsion, increased force elevated LME cracking. It was shown that high force increased the sudden indentation of the electrode into the substrate (electrode collapse), leading to rapid cooling of the weld shoulder. The rapid cooling increased the thermal stresses associated with the collapse event, promoting LME. This study established that the electrode force has two distinct roles on LME. When welding below the expulsion current, high force decreased LME. On the other hand, when welding above the expulsion current, more severe LME cracking was observed at high electrode force. The results from this study show that expulsion itself (excluding its association with increased heat input) is a factor contributing to LME cracking, which highlights the importance of considering the expulsion phenomenon in designing LME resistant welding schedules.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Corrosion Behavior and Inhibition · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. ENVIRONMENTAL PROTECTION AGENCY 40 CFR parts 86 and 600 revised 2023 and later model year light-duty vehicle greenhouse gas emissions standards n.d.
2. Advanced high strength steel in Auto industry: an overview10.48084/etasr.444 ↗
3. Light-weight materials and their automotive applications10.4271/2014-28-0025 ↗
4. Three generations of advanced high strength steels in the automotive industry10.1007/978-981-15-9529-5_7 ↗
5. The metallurgy of zinc-coated steel10.1016/S0079-6425(98)00006-1 ↗
6. Kimchi M, Phillips DH (Welding instructor). Resistance spot welding : fundamentals and applications for the automotive industry n.d.:115.
7. Liquid zinc embrittlement of twinning-induced plasticity steel10.1016/j.scriptamat.2011.12.040 ↗
8. Role of spot weld electrode geometry on liquid metal embrittlement crack development10.1016/j.jmapro.2019.11.015 ↗
9. Prevention of liquid metal embrittlement cracks in resistance spot welds by adaption of electrode geometry10.1080/13621718.2019.1693731 ↗
10. Critical design parameters of the electrode for liquid metal embrittlement cracking in resistance spot welding10.1007/s40194-019-00797-y ↗
11. A novel electrode tip geometry to mitigate liquid metal embrittlement during resistance spot welding10.1007/s40194-022-01343-z ↗
12. Liquid metal embrittlement of resistance spot welded 1180 TRIP steel: effect of electrode force on cracking behavior10.1007/s12540-018-0180-x ↗
13. Evaluation of surface crack in resistance spot welds of zn-coated steel10.2320/matertrans.M2013244 ↗
14. Impact of liquid metal embrittlement inner cracks on the mechanical behavior of 3rd generation advanced high strength steel spot welds10.1016/j.jmrt.2021.11.100 ↗
15. Liquid metal embrittlement in resistance spot welding and hot tensile tests of surface-refined TWIP steels10.1088/1757-899X/118/1/012002 ↗
16. Meschut G, Böhne C, Rethmeier M, Biegler M, Frei J. AHSS implementation solutions - LME program. Brussels, Belgium: 2020.
17. Predicting liquid metal embrittlement severity in resistance spot welding using hot tensile testing data10.1007/s40194-022-01320-6 ↗
18. Effect of multiple pulse resistance spot welding schedules on liquid metal embrittlement severity10.1115/1.4044099 ↗
19. Reduction in liquid metal embrittlement cracking using weld current ramping10.1007/s40194-019-00790-5 ↗
20. Resistance spot welding with variable electrode force—development and benefit of a force profile to extend the weldability of 22MnB5+AS15010.1007/s40194-020-01001-2 ↗
21. Liquid metal embrittlement-free welds of Zn-coated twinning induced plasticity steels10.1016/j.scriptamat.2015.11.027 ↗
22. Avoidance of liquid metal embrittlement during resistance spot welding by heat input dependent hold time adaption10.1080/13621718.2020.1795585 ↗
23. Kasuya T, Yurioka N. Carbon equivalent and multiplying factor for hardenability of steel n.d.
24. 2012
25. Occurrence of liquid-metal-embrittlement in a fully ferritic microstructure10.1016/j.mtla.2021.101036 ↗
26. Significance of cutting plane in liquid metal embrittlement severity quantification10.1007/s42452-021-04608-2 ↗
27. Quantifying the link between crack distribution and resistance spot weld strength reduction in liquid metal embrittlement susceptible steels10.1007/s40194-019-00712-5 ↗
28. Midawi ARH, Barber B, Pearson K, Sherepenko O. Comparative analysis of liquid metal embrittlement reduction methods in zinc-coated gen3-AHSS n.d.
29. The influence of electrode indentation rate on LME formation during RSW10.29391/2022.101.015 ↗