journal article·2023-03Open access

Effects of laser welding parameters on the porosity and acicular phase in SiCp/6092 aluminum matrix composite welded joints

Zeyu Wang, Hongyang Cao, Hongliang Li, Dan Wang, Hongbo Xia, Hassaan Ahmad Butt, Manni Li, Duo Liu

Abstract

Al matrix composites (AMCs) are preferred engineering materials for aerospace and automotive industries owing to their high specific strength, superior wear resistance and low thermal expansion. It is a challenge to achieve high-quality fusion welded joints of AMCs because of the occurrence of defects such as pores, particles segregation and acicular phases. In this study, the effects of laser welding parameters including laser power, welding speed and laser incident angle on the formation of porosity and acicular phase were investigated in SiCp/6092 aluminum matrix composite welded joints using orthogonal experimental method. Range analysis of the orthogonal test results showed that the laser power and the welding speed had the greatest influence on the porosity and acicular phase size during the laser welding of aluminum matrix composites. At a heat input of 60 J/mm, the porosity in the weld was only 1.6% while that at 190 J/mm was 15.2%. Higher heat input produced a much larger size of brittle Al4C3 phases. The size of the acicular phase Al4C3 at the top and bottom of the weld was larger than that in the middle. Active Ti was added to the weld zone to mitigate the adverse effect of Al4C3 brittle phase and porosity on mechanical properties. The ultimate tensile strength increased from 115 MPa in direct laser welding to 148 MPa for the laser welding process employing the Ti interlayer. This work will provide referenceable data for designing high-quality AMC welded joints for aerospace and automotive industries.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (50)

Show source-provided references
1. Cui · 2003 · vol. 249 · 45
2. Joining of aluminium based metal matrix composites10.1179/imr.1996.41.2.41 ↗
3. Investigation on reactive diffusion bonding of SiCp/6063 MMC by using mixed powders as interlayers10.1016/j.jmatprotec.2007.02.028 ↗
4. Effect of inclusion of SiC particulates on the mechanical resistance behaviour of stir-cast AA6063/SiC composites10.1016/j.matdes.2014.09.067 ↗
5. Review on experimental study of Nd: YAG laser beam welding, with a focus on aluminium metal matrix composites10.14419/ijet.v5i3.5984 ↗
6. A case study of mechanical and metallurgical properties of friction stir welded AA6063 AMC
7. A parametric study of friction stir welded AA6061/SiC AMC and its effect on microstructure and mechanical properties10.1016/j.matpr.2020.02.933 ↗
8. Friction stir welding of multi-walled carbon nanotubes reinforced Al matrix composites10.1016/j.matchar.2018.09.033 ↗
9. Preliminary investigation on joining performance of SiCp-reinforced aluminum metal matrix composite (Al/SiCp-MMC) by vacuum brazing10.1016/S1359-835X(98)00186-9 ↗
10. Active brazing filler metal on SiC particle reinforced aluminum matrix composites10.1179/1362171815Y.0000000024 ↗
11. Vacuum brazing of high volume fraction SiC particles reinforced aluminum matrix composites
12. Influence of interface reactions on fracture mechanisms in TIG arc-welded aluminum matrix composites10.1016/S0266-3538(99)00168-2 ↗
13. Fusion and friction stir welding of aluminum-metal-matrix composites10.1007/s11661-005-0093-4 ↗
14. Partial penetration laser-based welding of aluminum alloy (AA 5083-H32)10.1016/j.ijleo.2016.05.007 ↗
15. On the influence of laser beam welding parameters for autogenous AA2198 welded joints10.1007/s00170-020-05893-8 ↗
16. Novel local shielding approach for the laser welding based additive manufacturing of large structural space components from titanium10.2351/7.0000114 ↗
17. In situ SEM study on tensile fractured behavior of Al/steel laser welding-brazing interface10.1016/j.matdes.2022.111320 ↗
18. Effect of process parameters on bead properties of A359/SiC MMCs welded by laser10.1016/j.compositesa.2006.04.014 ↗
19. Research on laser welding of aluminum matrix composite SiCw/606110.1016/j.vacuum.2006.01.023 ↗
20. Microstructures and mechanical properties in laser beam welds of titanium matrix composites10.1179/1362171813Y.0000000176 ↗
21. Effects of minor Zr addition on the microstructure and mechanical properties of laser welded joint of Al/SiCp metal-matrix composite10.1016/j.jmapro.2019.12.004 ↗
22. Influence of welding process on microstructure and properties of laser welding of SiCp/6061 Al matrix composite10.3389/fmats.2021.779324 ↗
23. Electromagnetic stirring control for resistance spot welding of SiCp/Al composites10.1016/j.jmapro.2021.06.048 ↗
24. Microstructure and process characterization of laser-cold metal transfer hybrid welding of AA6061 aluminum alloy10.1007/s00170-013-4916-y ↗
25. Effect of arc-ultrasound on microstructures and mechanical properties of plasma arc welded joints of SiCp/Al MMCs10.1016/S1003-6326(11)60709-7 ↗
26. ‘In-situ’weld-alloying/laser beam welding of SiCp/6061Al MMC
27. Weldability of Al99-SiC composites by CO2 laser welding10.1177/0021998308105435 ↗
28. Laser welding of dissimilar metal joint of 6061 Al alloy and Al matrix composite
29. Mechanical properties of laser welded joints of high volume fraction SiCp/Al aluminum matrix composite
30. Optimization of welding process parameters for activated tungsten inert welding of inconel 625 using the technique for order preference by similarity to ideal solution methodology10.1007/s13369-021-05409-w ↗
31. A convenient method for quantifying collagen fibers in atherosclerotic lesions by ImageJ software
32. Performance of vibration-assisted laser welded joints based on orthogonal experiment design10.1007/s11665-021-06362-3 ↗
33. Influence of plasma-MIG welding parameters on aluminum weld porosity by orthogonal test10.1016/S1003-6326(09)60310-1 ↗
34. Effects of Ti on the forming, microstructure and mechanical properties of laser welded joints of SiCp/2A14 composites10.1016/j.jmrt.2021.11.017 ↗
35. Pulsed Nd-YAG laser welding of a SiC particulate reinforced aluminum alloy composite10.1023/A:1008826513679 ↗
36. Electron beam welding of SiCp/LD2 composite10.1016/S1003-6326(06)60332-4 ↗
37. Comparison of structure and performance of laser welded joints of SiCp/Al composite materials
38. The effect of Zr addition on the laser welding of SiCp/2A14Al composite10.1016/j.jmrt.2021.10.097 ↗
39. Behavior of al4c3 particles during flotation and sedimentation in aluminum melts10.1007/s11663-020-02049-7 ↗
40. Sinusoidal oscillating laser welding of 7075 aluminum alloy: hydrodynamics, porosity formation and optimization10.1016/j.ijheatmasstransfer.2019.05.111 ↗
41. Interfacial microstructure and growth mechanism of Al4C3 in Grf/Al composites fabricated by liquid pressure method10.1016/j.micron.2014.04.007 ↗
42. Effect of Mg content on the thermodynamics of interface reaction in Cf/Al composite10.1007/s11661-012-1090-z ↗
43. Effect of temperature gradient on microstructure evolution in Ni–Al–Cr bond coat/substrate systems: a phase-field study10.1016/j.surfcoat.2014.10.061 ↗
44. Microstructure and mechanical characterization of Nd: YAG laser beam welded AA6061/10 wt% ZrB2 aluminum matrix composites
45. Research on laser full-penetration welding in situ tib2 particulate reinforced ZL101 composites10.4028/www.scientific.net/AMR.97-101.3967 ↗
46. Electron and laser beam welding of high strain rate superplastic Al-6061/SiC composites10.1007/s11661-001-0047-4 ↗
47. Mechanical properties and wear resistance of aluminum composite welded by electron beam10.1016/S1003-6326(11)60951-5 ↗
48. Study on laser welding of AA1100-16 vol.% B4C metal–matrix composites10.1016/j.compositesb.2011.11.044 ↗
49. Effect of Ti-Al on microstructures and mechanical properties of plasma arc in-situ welded joint of SiCp/Al MMCs10.1016/S1003-6326(08)60140-5 ↗
50. In situ study on fracture behaviors of SiC/2A14 Al composite joint: Co-construction of microstructure and mechanical properties via laser welding10.1016/j.compositesb.2022.109882 ↗