Enhancing wear resistance in Al-7075 composites through conventional mixing and casting techniques
Source abstract
Abstract
Aluminium 7075 alloy composite are highly sought after materials because of their superior strength, light weight and exhibiting enhanced tribological characteristics. An electric resistance furnace and the metal die process were used to develop this aluminium (Al 7075) alloy hybrid composites, with reinforcing provided by E-glass short fibres and aluminium oxide (Al2O3) particulates. The Al 7075 alloy composites have been cast by employing stirring technique at various weight percentages of E-glass short fibres (2 %, 4 %, 6 %, and 8 %) and Al2O3 particles (3 %, 6 %, 9 %, and 12 %). Microscopic examination demonstrates that Al2O3 particle distribution within Aluminium matrix has been uniform. Hardness of the in-situ Al–Al2O3-E-glass-based composites rose by 10.58 %, 22.35 %, 50.58 %, and 41.17 % in comparison to its base alloy. Tensile strength of the 2 to 8 wt% E-glass with 3–12 wt% Al2O3 stir-cast composites increased by 9.08 %, 15.91 %, 19.09 %, and 7.27 % when compared with the aluminium matrix, whereas ductility reduced by 8.9 %, 12.5 %, 18.75 %, and 25 %. An experiment on wear rate was carried out using a pin-on-disk benchtop test equipment. The examination was performed at varying weights and sliding speeds, and the resulted demonstrated that composite materials exhibit higher wear resistance than Al matrix. Furthermore, the presence of Al2O3 and E-glass resulted in lower wear loss across all applied loads and sliding velocities. Lower wear rates in these composites were attributed to hardness and the interfacial bonding between the Al alloy and the in-situ reinforcement.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Studies on 7075 aluminum alloy MMCs with milled carbon fibers as reinforcements10.1007/s12666-017-1233-4 ↗
2. Kumaraswamy · 2023
3. Preparation and casting of metal-particulate non-metal composites10.1007/BF02644158 ↗
4. Eliasson · 1995 · 3
5. Microstructure and mechanical properties of the semisolid slurries and rheoformed component of nano-sized SiC/7075 aluminum matrix composite prepared by ultrasonic-assisted semisolid stirring10.1016/j.msea.2015.04.064 ↗
6. Bhowmik · 2020
7. Tensile behavior of B4C particulate reinforced Al2024 alloy metal matrix composites10.5937/fmet1701093N ↗
8. Influence of process parameters in machining the hybrid aluminum metal matrix composites in wire cut EDM-An experimental investigation
9. Natrayan · 2019 · 1
10. Gopalakrishnan · 2012 · 302
11. Al6061 hybrid metal matrix composite reinforced with alumina and molybdenum disulphide10.1155/2016/6127624 ↗
12. Studies on mechanical and wear properties of Al6061/beryl composites
13. Manipulating the powder size to achieve enhanced strength and ductility in harmonic structured Al alloy10.1080/21663831.2019.1580621 ↗
14. Studies on 3 and 9 wt.% of B4C particulates reinforced Al7025 alloy composites
15. Wear characterization of Al7075 Alloy hybrid composites10.30544/821 ↗
16. Hardness and tensile behavior of Al2219-TiC metal matrix composites
17. Experimental investigations on mechanical and wear behaviour of 2014Al–Al2O3 composites10.1007/s40735-020-00341-2 ↗
18. Analysing the coupled effects of compressive and diffusion induced stresses on the nucleation and propagation of circular coating blisters in the presence of micro-cracks10.1016/j.engfailanal.2016.07.003 ↗
19. Preparation and evaluation of mechanical and wear properties of Al6061 reinforced with graphite and SiC particulate metal matrix composites
20. Mechanical and tribological behavior of flyash, red mud and mica particles reinforced Al 7075 alloy hybrid metal composites
21. Fiber reinforced metal matrix composites - a review10.1016/j.matpr.2020.07.423 ↗
22. Investigating the mechanical properties of Al 7075 alloy for automotive applications: synthesis and analysis
23. Influence of particulates on microstructure, mechanical and fractured behaviour on Al-7075 alloy composite by FEA10.1080/14484846.2023.2276987 ↗
24. Mechanical behaviour of Al7075 alloy Al2O3/E-Glass hybrid composites for automobile applications10.1016/j.matpr.2022.08.460 ↗
25. Thermal analysis of Ni-Cu alloy nanocomposites processed by sand mold casting10.1155/2022/2530707 ↗