journal article·2024-01Open access

Coupling effect between electromigration and joule heating on the failure of ball grid array in 3D integrated circuit technology

Yifan Yao, Yuxuan An, K.N. Tu, Yingxia Liu

Abstract

Ball Grid Array (BGA) packaging method has been widely used in microelectronic devices, and electromigration (EM) in BGA is a crucial reliability issue, determining the performance of the products. Herein, we report a new failure mode induced by a coupling effect of EM and Joule heating in BGA structure. The test sample consists of a roll of 500 μm-BGA solder joints with upper and lower Cu under-bump-metallization (UBM) of different thicknesses, 16 μm, and 68 μm, respectively. Open failures of the thinner cathodic Cu UBM at the contacting area with solder joint were observed under four different EM conditions (130 °C-3000 A/cm2, 160 °C-2300 A/cm2, 160 °C-3000 A/cm2, and 160 °C-4600 A/cm2). Infrared (IR) results reveal the temperature at the thinner Cu UBM is higher than that in the solder joint as well as at the thicker Cu UBM. Simulation results elucidate the current density at the contacting area is about 22 times higher than the average density in the solder joint, so the effect of current crowding can be very serious in the failure site. Furthermore, severe current crowding and Joule heating promote the nucleation rate of voids at the joint location, which can further increase the current density and temperature, leading to a positive feedback effect until an open failure occurs in the circuitry. Our analysis enables the discussion of a coupling failure mode of EM and Joule heating in BGA, and provides a valuable guide of device design against EM failure in consumer electronic products.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Copper Interconnects and Reliability

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Growth behavior and reliability of interfacial IMC for Sn58Bi/Cu and Sn58Bi–AlN/Cu solder joints applied in IGBT modules10.1016/j.jmrt.2022.11.013 ↗
2. Material innovation opportunities for 3D integrated circuits from a wireless application point of view10.1557/mrs.2015.9 ↗
3. Reliability of key technologies in 3D integration10.1016/j.microrel.2012.08.011 ↗
4. Recent advances and trends in advanced packaging
5. Lead-free solders in microelectronics10.1016/S0927-796X(00)00010-3 ↗
6. Lau · 2020
7. Novel approaches to current BGA packaging challenges
8. Electromigration in three-dimensional integrated circuits10.1063/5.0139658 ↗
9. K.N. Tu. Reliability challenges in 3D IC packaging technology. Microelectron Reliab 51(3);517-523.10.1016/j.microrel.2010.09.031 ↗
10. How 2D semiconductors could extend Moore's law10.1038/d41586-019-00793-8 ↗
11. Reliability study of 3D IC packaging based on through-silicon interposer (TSI) and silicon-less interconnection technology (SLIT) using finite element analysis10.1016/j.microrel.2015.12.041 ↗
12. Effect of Joule heating and current crowding on electromigration in mobile technology10.1063/1.4974168 ↗
13. Transition from flip chip solder joint to 3D IC microbump: its effect on microstructure anisotropy10.1016/j.microrel.2012.07.029 ↗
14. New challenges of miniaturization of electronic devices: electromigration and thermomigration in lead-free solder joints10.1016/j.matdes.2020.108726 ↗
15. Electromigration in thin aluminum films on titanium nitride10.1063/1.322842 ↗
16. Structure and properties of lead-free solders bearing micro and nano particles10.1016/j.mser.2014.06.001 ↗
17. Review of ultrasonic-assisted soldering in Sn-based solder alloys10.1007/s10854-023-10063-z ↗
18. Enhancement of structure and properties of Sn58Bi solder by AlN ceramic particles10.1016/j.jmrt.2022.06.001 ↗
19. Electromigration and thermomigration in Pb-free flip-chip solder joints10.1146/annurev.matsci.38.060407.130253 ↗
20. Electromigration behavior of Cu/Sn3.0Ag0.5Cu/Cu ball grid array solder joints10.1007/s10854-019-00925-w ↗
21. Study of void formation due to electromigration in flip-chip solder joints using Kelvin bump probes10.1063/1.2226989 ↗
22. Temperature-dependent failure mechanism of SnAg solder joints with Cu metallization after current stressing: experimentation and analysis10.1063/1.4821427 ↗
23. Effects of impurities on void formation at the interface between Sn-3.0Ag-0.5Cu and Cu electroplated films10.1007/s10854-021-05824-7 ↗
24. Void-free interface between in and high-impurity Cu joint10.1080/13621718.2023.2259720 ↗
25. Effect of Sn grain orientation on growth of Cu-Sn intermetallic compounds during thermomigration in Cu-Sn2.3Ag-Ni microbumps10.1016/j.matlet.2018.10.112 ↗
26. Effect of Sn grain orientation on reliability issues of Sn-rich solder joints10.3390/ma15145086 ↗
27. Effect of Al-trace degradation on Joule heating during electromigration in flip-chip solder joints10.1063/1.2644061 ↗
28. Electromigration induced failure on lead-free micro bumps in three-dimensional integrated circuits packaging10.1063/1.4737154 ↗
29. Effect of passivation opening on electromigration in eutectic SnPb solder joints
30. Three-dimensional thermoelectrical simulation in flip-chip solder joints with thick underbump metallizations during accelerated electromigration testing10.1007/s11664-006-0060-x ↗
31. Thermomigration of Cu-Sn and Ni-Sn intermetallic compounds during electromigration in Pb-free SnAg solder joints10.1557/jmr.2011.25 ↗
32. Local melting induced by electromigration in flip-chip solder joints10.1007/BF02692560 ↗
33. Kirkendall void formation in eutectic SnPb solder joints on bare Cu and its effect on joint reliability10.1063/1.1839637 ↗
34. Studies on solder bump electromigration in Cu/Sn-3Ag-0.5Cu/Cu system10.1016/j.microrel.2006.09.028 ↗
35. Effect of electromigration-induced back stress gradient on nanoindentation marker movement in SnAgCu solder joints10.1063/1.2397549 ↗
36. Degradation behaviors of micro ball grid array (μBGA) solder joints under the coupled effects of electromigration and thermal stress10.1007/s10854-016-5289-4 ↗
37. Non-destructive micro analysis of electromigration failures in solder microbumps using 3D X-ray computed tomography10.1016/j.matchar.2022.112404 ↗
38. Fundamentals of electromigration
39. Newton's law of cooling and its interpretation10.1016/j.ijheatmasstransfer.2012.03.035 ↗
40. Configurational heat capacity and entropy of borosilicate melts10.1016/S0022-3093(96)00646-1 ↗
41. Studies on gas-solid heat transfer during pneumatic conveying10.1016/j.ijheatmasstransfer.2007.09.042 ↗
42. Synergistic effect of electromigration and Joule heating on system level weak-link failure in 2.5D integrated circuits10.1063/1.4932598 ↗