Analysis of droplet characteristics and cooling lubrication effects in MQL milling of 316L stainless steel
Source abstract
Abstract
The infiltration and cooling effect of lubricant droplets in the cutting zone largely depend on setting minimum quantity lubricant (MQL) system parameters appropriately. The study determines the optimal spray angle and spray distance relying on the geometric position relationship between the nozzle and the overall cutting zone. A numerical model that combines computational fluid dynamics (CFD) and discrete phase model (DPM) is presented to simulate droplet transport process for dynamic milling and one-tooth milling by flow field distribution and droplet characteristics. The influences of different spray distances and spray angles on the infiltration process and cutting tool temperature are analyzed. The experiments aimed at verifying the results of the analysis are conducted by measuring cutting force, cutting temperature, surface roughness, surface microtopography and tool wear. The result indicates that the spray distance has a significant impact on the jet divergence, and insufficient lubrication or excessive lubrication is effectively avoided with the optimal cutting distance. Spraying in the direction of cutting-out promotes the accessibility of the lubricant and greater concentration of droplets in the cutting zone, especially later in the cutting process, which results in increased infiltration, reduced friction, and improved heat dissipation. Moreover, experiments demonstate that the optimal state of jetting in the direction of cutting-out is 46 °C lower than that of dry cutting, the surface roughness is reduced by 19.8%, and the wear amount is reduced by roughly 34%. This study has a better understanding of the setting of spray distance and spray angle in MQL milling and the development of equipment, which provides theoretical guidance for the optimization of MQL system parameters in practical applications.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Fluid Dynamics and Heat Transfer · Particle Dynamics in Fluid Flows · Fluid Dynamics and Mixing
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (47)
Show source-provided references
1. A numerical and experimental study to investigate convective heat transfer and associated cutting temperature distribution in single point turning10.1007/s00170-017-0975-9 ↗
2. Metal cutting lubricants and cutting tools: a review on the performance improvement and sustainability assessment10.1007/s00170-019-04890-w ↗
3. Machinability studies of austenitic stainless steel (AISI 304) using PVD cathodic arc evaporation (CAE) system deposited AlCrN/TiAlN coated carbide inserts10.1016/j.proeng.2013.09.167 ↗
4. Analysis of heat transfer coefficient on workpiece surface during minimum quantity lubricant grinding10.1007/s00170-012-4330-x ↗
5. Numerical and experimental analysis of turbulent flow and heat transfer of minimum quantity lubrication in a turning process using discrete phase model10.1016/j.icheatmasstransfer.2019.02.012 ↗
6. Environmentally friendly manufacturing: behavior analysis of minimum quantity of lubricant – MQL in grinding process
7. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions10.1016/j.jclepro.2012.03.014 ↗
8. A review identifying the effectiveness of minimum quantity lubrication (MQL) during conventional machining10.1007/s00170-017-0142-3 ↗
9. Hybrid nano-fluid-minimum quantity lubrication strategy for machining austempered ductile iron (ADI)10.1007/s12008-018-0491-7 ↗
10. Resource saving by optimization and machining environments for sustainable manufacturing: a review and future prospects10.1016/j.rser.2022.112660 ↗
11. Progress of machinability on the machining of Inconel 718: a comprehensive review on the perception of cleaner machining10.1016/j.clet.2021.100323 ↗
12. Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid10.1016/j.jmatprotec.2009.05.014 ↗
13. The effects of MQL and dry environments on tool wear, cutting temperature, and power consumption during end milling of AISI 1040 steel10.3390/met11111674 ↗
14. Dry and minimum quantity lubrication drilling of cast magnesium alloy (AM60)10.1016/j.ijmachtools.2010.02.001 ↗
15. Performance of MQL and nano-MQL lubrication in machining ER7 steel for train wheel applications10.3390/lubricants10040048 ↗
16. Performance assessment of minimum quantity castor-palm oil mixtures in hard-milling operation10.3390/ma14010198 ↗
17. Study of a multicriterion decision-making approach to the MQL turning of AISI 304 steel using hybrid nanocutting fluid10.3390/ma14237207 ↗
18. Effect of MQL condition on cutting performance of high-speed machining of GH4099 with ceramic end mills10.1016/j.triboint.2021.107401 ↗
19. Machinability evaluations of austempered ductile iron and cast steel with similar mechanical properties under eco-friendly milling conditions10.1016/j.jmrt.2021.01.123 ↗
20. A study on droplets sizes, their distribution and heat exchange for minimum quantity cooling lubrication (MQCL)10.1016/j.ijmachtools.2015.10.008 ↗
21. Investigation of cutting force and temperature of end-milling Ti-6Al-4V with different minimum quantity lubrication (MQL) parameters
22. Influence of oil mist parameters on minimum quantity lubrication -MQL grinding process10.1016/j.ijmachtools.2010.03.005 ↗
23. Experimental investigation into the effects of nozzle position, workpiece hardness, and tool type in MQL turning of AISI 1045 steel10.1080/10426914.2017.1401716 ↗
24. A computational fluid dynamics analysis of single and three nozzles minimum quantity lubricant flow for milling10.15282/ijame.10.2014.6.0157 ↗
25. Numerical analysis of the effect of air pressure and oil flow rate on droplet size and tool temperature in MQL machining10.1016/j.matpr.2020.07.518 ↗
26. Numerical and experimental optimizations of nozzle distance in minimum quantity lubrication (MQL) milling process10.1007/s00170-018-2928-3 ↗
27. Numerical investigation of thermal characteristics of spray cooling with minimum quantity lubrication in milling process10.1016/j.apm.2018.08.011 ↗
28. Suppression of notch wear of a whisker reinforced ceramic tool in air-jet-assisted high-speed machining of Inconel 71810.1016/j.precisioneng.2014.08.002 ↗
29. Characteristics of aerosol produced by an internal-mix nozzle and its influence on force, residual stress and surface finish in SQCL grinding10.1016/j.jmatprotec.2016.09.014 ↗
30. The multiphase particle-in-cell (MP-PIC) method for dense particulate flows10.1016/0301-9322(95)00072-0 ↗
31. Milling surface roughness for 7050 aluminum alloy cavity influenced by nozzle position of nanofluid minimum quantity lubrication10.1016/j.cja.2020.04.029 ↗
32. Minimum quantity lubrication-MQL turning of AISI 4140 steel alloy10.1016/j.jclepro.2013.05.011 ↗
33. Design and performance of an internal-cooling turning tool with micro-channel structures10.1016/j.jmapro.2019.08.011 ↗
34. Numerical study of flow and thermal characteristics in titanium alloy milling with hybrid nanofluid minimum quantity lubrication and cryogenic nitrogen cooling10.1016/j.ijheatmasstransfer.2021.121005 ↗
35. Cryogenic minimum quantity lubrication machining: from mechanism to application10.1007/s11465-021-0654-2 ↗
36. Effects of high-pressure cutting fluid with different jetting paths on tool wear in cutting compacted graphite iron10.1016/j.triboint.2016.06.029 ↗
37. Specific cutting energy modeling for turning nickel-based Nimonic 90 alloy under MQL condition10.1016/j.ijmecsci.2018.07.033 ↗
38. Dixit · 2018 · 45
39. Minimum quantity lubrication machining of aeronautical materials using carbon group nanolubricant: from mechanisms to application
40. Machining performance evaluation of Ti6Al4V alloy with laser textured tools under MQL and nano-MQL environments10.1016/j.jmapro.2020.02.014 ↗
41. Anti-frictional role of diamond and graphite suspended bio-oil based nano-aerosols at sliding interface of Al-SiCp and WC-6Co10.1016/j.triboint.2020.106596 ↗
42. Heat generation and temperature prediction in metal cutting: a review and implications for high speed machining10.1016/j.ijmachtools.2005.07.024 ↗
43. Performance evaluation of MQL parameters using Al2O3 and MoS2 nanofluids in hard turning 90CrSi steel10.3390/lubricants7050040 ↗
44. Cutting performance of cubic boron nitride-coated tools in dry turning of hardened ductile iron10.1016/j.jmapro.2020.04.081 ↗
45. Hybrid cooling-lubrication strategies to improve surface topography and tool wear in sustainable turning of Al 7075-T6 alloy10.1007/s00170-018-2870-4 ↗
46. Influence of MoS2 based nanofluid-MQL on tribological and machining characteristics in turning of AA 2024 T3 aluminum alloy10.1016/j.jmrt.2021.09.007 ↗
47. The assessment of cutting tool wear10.1016/j.ijmachtools.2003.11.006 ↗