Room temperature deformation mechanisms of a Fe–Mn–Al–C steel
Source abstract
Abstract
This study aims to investigate the deformation mechanisms of an austenite-based duplex Fe-Mn-Al-C steel at room-temperature through uniaxial tensile tests, strain rate sensitivity and stress relaxation analysis. Through numerical analysis and microstructural studies, this investigation reveals that increasing strain leads to the formation of low-angle boundaries (LABs) at the vicinity of grain boundaries. Consequently, these LABs play a facilitating role in the stress-assisted diffusion of carbon atoms, thereby triggering the dynamic strain aging (DSA) phenomenon. The evidence for this is substantiated by the strain rate sensitivity coefficient and stress relaxation results obtained from numerical analysis during uniaxial tensile tests. As deformation progresses, the misorientation of LABs increases, influencing the strain hardening behavior. The intensified DSA contributes to enhanced work hardening, while substructure development results in softening, creating a trade-off between these contrasting effects.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (61)
Show source-provided references
1. Low-density steels
2. Current state of Fe-Mn-Al-C low density steels10.1016/j.pmatsci.2017.05.002 ↗
3. Microstructure evolution and room temperature mechanical properties of a thermomechanically processed ferrite-based low density steel10.1016/j.msea.2019.03.048 ↗
4. Physical metallurgy of modern high strength steel sheets10.2355/isijinternational.41.520 ↗
5. An investigation into the reverse transformation of ferrite to austenite during friction stir processing of a duplex low-density steel
6. A general perspective of Fe–Mn–Al–C steels10.1007/s10853-018-2551-6 ↗
7. The effect of grain size and grain orientation on deformation twinning in a Fe-22wt.% Mn-0.6wt.% C TWIP steel10.1016/j.msea.2010.02.041 ↗
8. Deformation mechanisms in an austenitic single-phase duplex microstructured steel with nanotwinned grains10.1016/j.actamat.2014.08.054 ↗
9. Spectral TRIP enables ductile 1.1 GPa martensite10.1016/j.actamat.2016.03.070 ↗
10. The effects of prior austenite grain boundaries and microstructural morphology on the impact toughness of intercritically annealed medium Mn steel10.1016/j.actamat.2016.09.048 ↗
11. Evaluation of the crystallographic orientation relationships between FCC and BCC phases in TRIP steels10.2355/isijinternational.49.1601 ↗
12. Revealing the strain-hardening behavior of twinning-induced plasticity steels: theory, simulations, experiments10.1016/j.actamat.2012.09.064 ↗
13. Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe–Mn–C alloys10.1016/j.msea.2004.01.059 ↗
14. Effects of stacking fault energy on deformation mechanisms in Al-added medium Mn TWIP steel10.1007/s11661-019-05274-1 ↗
15. Microstructural development and deformation mechanisms during cold rolling of a medium stacking fault energy TWIP steel10.1016/j.jmst.2012.11.002 ↗
16. Stacking fault energy and deformation mechanisms in Fe-xMn-0.6C-yAl TWIP steel10.1016/j.msea.2016.08.106 ↗
17. Microstructure and tensile behavior of duplex low-density steel containing 5mass% aluminum10.1016/j.scriptamat.2012.09.030 ↗
18. The unexpected stress-strain response of medium Mn steel after friction stir welding10.1016/j.msea.2018.12.041 ↗
19. Novel ferrite–austenite duplex lightweight steel with 77% ductility by transformation induced plasticity and twinning induced plasticity mechanisms10.1016/j.actamat.2014.06.059 ↗
20. Dual-scale correlation of mechanical behavior in duplex low-density steel10.1016/j.scriptamat.2013.07.015 ↗
21. Optimizing the austenite stability in a ferritic lightweight steel through thermomechanical processing10.1016/j.matchar.2020.110367 ↗
22. On the origin of dynamic strain aging in twinning-induced plasticity steels10.1016/j.actamat.2011.07.040 ↗
23. On the fatigue and dwell-fatigue behavior of a low-density steel and the correlated microstructure origin of damage mechanism10.1016/j.jmrt.2021.10.135 ↗
24. Substructure hardening in duplex low density steel10.1016/j.matdes.2016.12.020 ↗
25. Effects of aging heat-treatment on dynamic strain aging behavior in high-Mn lightweight steel10.1016/j.matchar.2020.110316 ↗
26. Fe–Mn–C–Al low-density steel for structural materials: a review of alloying, heat treatment, microstructure, and mechanical properties10.1002/srin.202200191 ↗
27. Dynamic strain aging and twin formation during warm deformation of a novel medium-entropy lightweight steel10.1016/j.jmrt.2022.01.057 ↗
28. In-situ strain localization analysis in low density transformation-twinning induced plasticity steel using digital image correlation10.1016/j.optlaseng.2014.10.005 ↗
29. Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe–Mn–Al–C steel10.1016/j.actamat.2012.07.018 ↗
30. Thermodynamic modeling of the stacking fault energy of austenitic steels10.1016/j.actamat.2010.10.037 ↗
31. Derivation and variation in composition-dependent stacking fault energy maps based on subregular solution model in high-manganese steels10.1007/s11661-009-0050-8 ↗
32. Martensite reversion duality behavior in a cold-rolled high Mn transformation-induced plasticity steel10.1007/s11661-019-05385-9 ↗
33. Evolution of microstructure and mechanical properties in a cold deformed nitrogen bearing TRIP-assisted duplex stainless steel after reversion annealing10.1016/j.msea.2016.10.105 ↗
34. On the effect of Mn-content on the strength-ductility balance in Ni-free high N transformation induced plasticity steels10.1016/j.msea.2021.141260 ↗
35. Temperature dependence of tensile deformation behavior and strain hardening of lean duplex stainless steels10.1016/j.jmrt.2022.07.040 ↗
36. Deformation behavior of a high-plasticity nano/ultrafine-grained N-bearing duplex stainless steel: twin/twin-like induced plasticity effect10.1016/j.msea.2017.06.040 ↗
37. Transformation and twinning induced plasticity in an advanced high Mn austenitic steel processed by martensite reversion treatment10.1016/j.msea.2017.03.109 ↗
38. Effect of the Zener–Hollomon parameter on the microstructure evolution of dual phase TWIP steel subjected to friction stir processing10.1016/j.msea.2015.04.022 ↗
39. Effects of ferrite volume fraction on the tensile deformation characteristics of dual phase twinning induced plasticity steel10.1016/j.matdes.2013.06.033 ↗
40. The grain structure and phase transformations of TWIP steel during friction stir processing10.1007/s11665-015-1557-3 ↗
41. The microstructural evolution and mechanical properties of resistance spot welded Fe–31Mn–3Al–3Si TWIP steel10.1016/j.matdes.2014.10.090 ↗
42. Thermal stability of an ultrafine-grained dual phase TWIP steel10.1016/j.msea.2015.03.066 ↗
43. ASTM E8/E8M standard test methods for tension testing of metallic materials
44. On the short-time thermal phase-stability of as-cast AlCoCrFeNi2.1eutectic high entropy alloy10.1016/j.jmrt.2022.07.058 ↗
45. Thermally stable and corrosion resistant nanolaminated Al-Mn alloy with low angle boundary structures10.1016/j.jallcom.2022.165016 ↗
46. Microstructural evolution and strain hardening behavior of heat-treated 17-4 PH stainless steel
47. Design for Fe-high Mn alloy with an improved combination of strength and ductility10.1038/s41598-017-03862-y ↗
48. Work hardening behaviour and damage mechanisms in carbide-free bainitic steel during uni-axial tensile deformation10.1016/j.msea.2019.02.062 ↗
49. Effect of volume fraction of bainite on strain hardening behavior and deformation mechanism of F/B multi-phase steel10.1016/j.msea.2018.06.016 ↗
50. Strain hardening, strain rate sensitivity, and ductility of nanostructured metals10.1016/j.msea.2003.10.214 ↗
51. Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content10.1016/j.actamat.2014.10.052 ↗
52. Combined deformation twinning and short-range ordering causes serrated flow in high-manganese steels10.1016/j.msea.2019.01.042 ↗
53. Deformation rate controls atomic-scale dynamic strain aging and phase transformation in high Mn TRIP steels10.1016/j.actamat.2017.03.076 ↗
54. Stress relaxation and the structure size-dependence of plastic deformation in nanotwinned copper10.1016/j.actamat.2009.07.018 ↗
55. Twinning-induced plasticity (TWIP) steels10.1016/j.actamat.2017.06.046 ↗
56. Thermal activation parameters of plastic flow reveal deformation mechanisms in the CrMnFeCoNi high-entropy alloy10.1016/j.actamat.2017.10.014 ↗
57. Analysis of strain hardening behavior of a high-Mn TWIP steel using electron microscopy and cyclic stress relaxation10.1016/j.actamat.2022.118309 ↗
58. Stress-relaxation viewpoint to study the room-temperature cyclic deformation behavior of a low-density steel10.1016/j.ijfatigue.2020.105673 ↗
59. Spinodal decomposition of B2-phase and formation of Cr-rich nano-precipitates in AlCoCrFeNi 2.1 eutectic high-entropy alloy
60. Substructure induced twinning in low density steel10.1016/j.scriptamat.2016.10.001 ↗
61. Trading off between dynamic strain aging and substructure evolution in κ-carbide-free lightweight steel at room temperature10.1016/j.scriptamat.2018.07.044 ↗