Multi-build orientation effects on microstructural evolution and mechanical behavior of truly as-built selective laser melting Ti6Al4V alloys
Source abstract
Abstract
The unique combination of lightweight, strength, corrosion resistance, high-temperature resistance, and biocompatibility make Ti6Al4V alloy an important material in metal contact of solar cells, and selective laser melting (SLM) enables the production of Ti6Al4V parts complex geometries that would be difficult or impossible to produce using traditional manufacturing methods. The build orientation of SLM process presents an essential effect on the quality of the produced parts, and thus, in this study it investigates the impact of multi-build orientation (0°, 30°, 45°, 60°, 90°) on the microstructural evolution and mechanical behavior of truly as-built Ti6Al4V alloys produced by SLM. The microstructure analysis revealed the presence of ordered subsurface pores, located at a distance of about 50 μm–150 μm from the sample surface. The microstructure consisted primarily of α′ martensite with a small amount of β phase. Massive transformation was observed in the 30° and 45° samples, with corresponding grain sizes of 5 μm and 10 μm, respectively. To be specific, the content of β phase and ultimate tensile strength (UTS) varied with the sample orientation, and the 45° build orientation exhibited the highest content of β phase with value of approximately 2.8%, but also the lowest UTS and elongation, which were 1161 MPa and 3.99%, respectively.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Remarkable increase in high-cycle fatigue resistance in a titanium alloy with a fully lamellar microstructure10.1016/j.ijfatigue.2020.105724 ↗
2. Controlling martensitic decomposition during selective laser melting to achieve best ductility in high strength Ti-6Al-4V10.1016/j.msea.2018.12.047 ↗
3. Grain size characterization method of dual-phase titanium alloys with complex microstructure based on laser ultrasonic10.1016/j.measurement.2023.112670 ↗
4. Effect of surface oxidation on wear and tribocorrosion behavior of forged and selective laser melting-based TC4 alloys10.1016/j.triboint.2022.107780 ↗
5. Influence of 3D-printing on the behaviour of Ti6Al4V in high-speed friction10.1016/j.triboint.2020.106557 ↗
6. Ultra-high specific strength Ti6Al4V alloy lattice material manufactured via selective laser melting10.1016/j.msea.2022.142956 ↗
7. Assessment of microstructural evolution and associated tensile behavior in thin-walled Ti6Al4V parts manufactured via selective laser melting10.1016/j.matchar.2022.112481 ↗
8. Tribological properties of additive manufactured Ti6Al4V against cemented carbide under dry sliding conditions10.1016/j.triboint.2021.107358 ↗
9. Toward low and high cycle fatigue behavior of SLM-fabricated NiTi: considering the effect of build orientation and employing a self-heating approach10.1016/j.ijmecsci.2020.105878 ↗
10. Prediction of anisotropic LCF behavior for SLM Ti-6Al-4V considering the spatial orientation of defects10.1016/j.ijfatigue.2022.106734 ↗
11. On the effect of build orientation and residual stress on the corrosion of 316L stainless steel prepared by selective laser melting10.1016/j.corsci.2020.109149 ↗
12. Metal additive manufacturing: a Review of mechanical properties10.1146/annurev-matsci-070115-032024 ↗
13. Effect of build orientation and elevated temperature on microhardness and deformation of dynamically tested SLM processed AlSi12 alloy10.1016/j.matpr.2020.07.514 ↗
14. Effect of build orientation on microstructure and tensile behaviour of selectively laser melted M300 maraging steel10.1016/j.msea.2020.140130 ↗
15. Effects of selective laser melting build orientations on the microstructure and tensile performance of Ti–6Al–4V alloy10.1016/j.msea.2020.139001 ↗
16. The effects of build orientation and hatch spacing on mechanical properties of medical Ti–6Al–4V alloy manufactured by selective laser melting10.1016/j.msea.2020.140649 ↗
17. Effect of build orientation on mechanical properties and microstructure of Ti-6Al-4V manufactured by selective laser melting10.1007/s11661-019-05322-w ↗
18. Experimental realisation of build orientation effects on the mechanical properties of truly as-built Ti-6Al-4V SLM parts10.1016/j.jmapro.2021.01.027 ↗
19. A novel hybrid selective laser melting/hot isostatic pressing of near-net shaped Ti-6Al-4V alloy using an in-situ tooling: interfacial microstructure evolution and enhanced mechanical properties10.1016/j.msea.2018.01.079 ↗
20. Dynamics of pore formation during laser powder bed fusion additive manufacturing10.1038/s41467-019-10009-2 ↗
21. Critical instability at moving keyhole tip generates porosity in laser melting10.1126/science.abd1587 ↗
22. Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting10.1016/j.matdes.2016.05.070 ↗
23. Martensitic transformations in Ti-6Al-4V (ELI) alloy manufactured by 3D Printing10.1016/j.matchar.2018.09.042 ↗
24. Effect of scanning strategy on variant selection in additively manufactured Ti-6Al-4V
25. Massive transformation in Ti–6Al–4V additively manufactured by selective electron beam melting10.1016/j.actamat.2015.11.011 ↗
26. Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti6Al4V by selective electron beam melting10.1016/j.matchar.2013.07.012 ↗
27. Fatigue life of titanium alloys fabricated by additive layer manufacturing techniques for dental implants10.1007/s11661-012-1470-4 ↗
28. Activated slip systems in bimodal Ti–6Al–4V plastically deformed at low and moderately high temperatures10.1016/j.msea.2020.140211 ↗