Constitutive model research on the hot deformation behavior of Ti6Al4V alloy under wide temperatures
Source abstract
Abstract
The hot compression tests of Ti6Al4V alloy were carried out at different temperatures (500, 600, 700, 800, and 900 °C) and different strain rates (0.01 s−1, 0.1 s−1, and 1 s−1). The hot deformation behavior of Ti6Al4V alloy is complex in a wide temperature range, and the phenomenon of negative strain rate sensitivity even appears at low temperature (500 °C and 600 °C). The phenomenological Arrhenius model, modified Fields-Backofen model (m-FB) and Gray Wolf Optimization Algorithm optimizing BP artificial neural network model (GWO-BPNN) were established. A new FB model (n-FB) was proposed based on m-FB model. The prediction accuracy and computational cost of these constitutive models were evaluated by mean absolute percentage error (MAPE), correlation coefficient (R) and the number of parameters. The comparison results show that the m-FB model, the GWO-BPNN model, and the n-FB model can predict the flow stress at all temperatures, but the Arrhenius model cannot be fitted at low temperature conditions, and the fitting effect of the Arrhenius model is the worst. The GWO-BPNN has the highest prediction accuracy based on that it has the maximum number of parameters. The MAPE and R values of n-FB model are 1.9093% and 0.993 respectively. Compared with the m-FB model, the MAPE value of n-FB is reduced by 64.64%.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metallurgy and Material Forming · Titanium Alloys Microstructure and Properties · High-Velocity Impact and Material Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (42)
Show source-provided references
1. Huang · 1991
2. Ductility of titanium alloy and stainless steel aerospace fasteners10.1007/s11668-015-0007-8 ↗
3. Modelling of dominant softening mechanisms for Ti-6Al-4V in steady state hot forming conditions10.1016/j.msea.2012.08.110 ↗
4. Effect of Al and Nb on the trigger stress for stress-induced martensitic transformation during tensile loading in Ti–Al–Nb alloys10.1016/j.msea.2007.10.021 ↗
5. Deformation mechanisms of Ti-6Al-4V during tensile behavior at low strain rate10.1007/s11665-007-9033-3 ↗
6. Fundamental aspects in vibration-assisted tapping10.1016/S0924-0136(02)00950-0 ↗
7. On the warm temperature strain accommodation mechanisms of Ti–6Al–4V alloy holding different starting microstructures10.1016/j.jmrt.2021.06.077 ↗
8. Diffusional transformation in Ti6Al4V alloy during isothermal compression10.1016/S1003-6326(19)65114-9 ↗
9. Characterization of Ti-6Al-4V alloy in the temperature range of warm metal forming and fracture analysis of the warm capping process10.1016/j.jmrt.2022.03.066 ↗
10. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working10.1016/j.matdes.2010.11.048 ↗
11. Flow stress description characteristics of some constitutive models at wide strain rates and temperatures
12. A microstructural based constitutive approach for simulating hot deformation of Ti6Al4V alloy in the α+ β phase region10.1016/j.msea.2019.01.081 ↗
13. A microstructural based constitutive approach for simulating hot deformation of Ti6Al4V alloy in the α+β phase region10.1016/j.msea.2019.01.081 ↗
14. A constitutive model and data for materials subjected to large strains, high strain rates, and high temperatures
15. A new phenomenological constitutive model for hot tensile deformation behaviors of a typical Al–Cu–Mg alloy10.1016/j.matdes.2013.05.036 ↗
16. Application of genetic algorithms for optimizing the Johnson–Cook constitutive model parameters when simulating the titanium alloy Ti-6Al-4V machining process10.1177/0954405412447735 ↗
17. Constitutive modeling and microstructure research on the deformation mechanism of Ti-6Al-4V alloy under hot forming condition10.1016/j.jallcom.2021.162128 ↗
18. Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys10.1016/j.ijplas.2003.06.005 ↗
19. Study of khan-huang-liang (KHL) anisotropic deformation model for deep drawing behaviour of inconel 718 alloy IOP Publishing10.1088/1757-899X/967/1/012054 ↗
20. Study of hot deformation behavior using phenomenological based constitutive model for austenitic stainless steel 31610.1016/j.matpr.2017.12.063 ↗
21. Flow stress prediction of zircaloy-4 at elevated temperatures using KHL constitutive model
22. Determination of strain hardening characteristics by torsion testing
23. Flow stress equation of AZ31 magnesium alloy sheet during warm tensile deformation10.1016/j.jmatprotec.2007.12.095 ↗
24. Constitutive modeling and the effects of strain-rate and temperature on the formability of Ti–6Al–4V alloy sheet10.1016/j.matdes.2013.09.069 ↗
25. Effect of strain rate upon plastic flow of steel10.1063/1.1707363 ↗
26. Constitutive equations for high temperature flow stress of aluminium alloys10.1179/mst.1997.13.3.210 ↗
27. Constitutive modeling for elevated temperature flow behavior of 42CrMo steel10.1016/j.commatsci.2007.08.011 ↗
28. Plastic properties and constitutive equations of 42CrMo steel during warm forming process10.1179/1743284713Y.0000000378 ↗
29. A comparative study on modified and optimized Zerilli-Armstrong and arrhenius-type constitutive models to predict the hot deformation behavior in 30Si2MnCrMoVE steel10.1016/j.jmrt.2022.08.134 ↗
30. Characterization of the hot deformation behavior and microstructural evolution of Ti–6Al–4V sintered preforms using materials modeling techniques10.1016/j.jallcom.2016.03.146 ↗
31. Application of neural networks to predict the elevated temperature flow behavior of a low alloy steel10.1016/j.commatsci.2008.01.039 ↗
32. Using genetic algorithm-back propagation neural network prediction and finite-element model simulation to optimize the process of multiple-step incremental air-bending forming of sheet metal10.1016/j.matdes.2009.06.019 ↗
33. Prediction of clad characteristics using ANN and combined PSO-ANN algorithms in laser metal deposition process10.1016/j.surfin.2020.100699 ↗
34. Springback prediction for sheet metal forming based on GA-ANN technology10.1016/j.jmatprotec.2006.11.087 ↗
35. Modeling constitutive relationship of Ti17 titanium alloy with lamellar starting microstructure10.1016/j.msea.2012.01.027 ↗
36. Phase transformation and constitutive models of a hot compressed TC18 titanium alloy in the α+ β regime10.1016/j.vacuum.2018.08.020 ↗
37. Research on hot deformation behavior of Zr-4 alloy based on PSO-BP artificial neural network10.1016/j.jallcom.2020.154047 ↗
38. Machine learning-based modeling of the coupling effect of strain rate and temperature on strain hardening for 5182-O aluminum alloy10.1016/j.jmatprotec.2022.117501 ↗
39. Strain-rate sensitivity and microstructural evolution in a Mg–Al–Zn alloy10.1016/j.scriptamat.2010.06.047 ↗
40. The effects of strain rate and temperature on the compressive deformation behaviour of Ti-6Al-4V alloy10.1016/S0924-0136(97)00080-0 ↗
41. Temperature dependent work hardening in Ti–6Al–4V alloy over large temperature and strain rate ranges: experiments and constitutive modeling10.1016/j.matdes.2015.06.048 ↗
42. Grey wolf optimizer10.1016/j.advengsoft.2013.12.007 ↗