journal article·2023-11Open access

Microstructure features and mechanical properties of non-heat treated HPDC Al9Si0.6Mn–TiB2 alloys

Chengyang Hu, Hongyi Zhu, Yihao Wang, Cunjuan Xia, Jiwei Geng, Dong Chen, Huawei Zhang, Mingliang Wang, Haowei Wang

Abstract

This study aimed to enhance the mechanical properties of high pressure die casting (HPDC) Al9Si0.6Mn alloys by incorporating in-situ TiB2 particles. The effects of TiB2 addition on the microstructure and mechanical properties of as-HPDC Al9Si0.6Mn alloys were investigated. The results showed that TiB2 addition refined the bimodal grain structure and eutectic Si morphology in the central region of the as-HPDC alloys, which was the primary contributor to the mechanical properties. The thickness of the skin region and band zone increased with increasing TiB2 addition, while the central region exhibited a reduced thickness but remained dominant on the entire cross-section. The optimal TiB2 content was found to be 1wt%, resulting in the 23.4% reduction in grain size and 10.7% enhancement in yield strength. The modified strengthening model based on the microstructure features of the central region accurately predicted the yield strengths of as-HPDC alloys. Finally, the morphological strengthening factors induced by TiB2 particles were analytically illustrated in the HPDC Al9Si0.6Mn-TiB2 alloys.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (68)

Show source-provided references
1. Lightweight materials equal lightweight greenhouse gas emissions?: a historical analysis of greenhouse gases of vehicle material substitution10.1016/j.jclepro.2019.119805 ↗
2. Advanced lightweight materials for Automobiles: a review10.1016/j.matdes.2022.110994 ↗
3. A new recycled Al-Si-Mg alloy for sustainable structural die casting applications10.1007/s11661-022-06711-4 ↗
4. Enhanced mechanical properties and thermal conductivity of high-pressure die-cast AlMg6Si2MnZr alloy by controlling the externally solidified crystals10.1016/j.jmatprotec.2022.117645 ↗
5. High performance Al/TiB2 composites fabricated by nanoparticle reinforcement and cutting-edge super vacuum assisted die casting process10.1016/j.compositesb.2019.107453 ↗
6. Squeeze casting: an overview10.1016/S0924-0136(99)00291-5 ↗
7. On the characterization of primary iron-rich phase in a high-pressure die-cast hypoeutectic Al-Si alloy10.1016/j.jallcom.2020.158580 ↗
8. High as-cast strength die-cast AlSi9Cu2Mg alloy prepared by nanoparticle strengthening with industrially acceptable ductility10.1016/j.jallcom.2020.156873 ↗
9. Processing, multiscale microstructure refinement and mechanical property enhancement of hypoeutectic Al-Si alloys via in situ bimodal-sized TiB2 particles10.1016/j.msea.2020.139081 ↗
10. On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 wt%Si alloy10.1016/j.pnsc.2019.04.008 ↗
11. Effect of Cu/Mg-containing intermetallics on the mechanical properties of the as-cast HVDC AlSiMgMnCu alloys by SBFSEM at nano-scale10.1016/j.jallcom.2022.166837 ↗
12. Advanced heat treated die-cast aluminium composites fabricated by TiB2 nanoparticle implantation10.1016/j.matdes.2019.108372 ↗
13. Effect of solidification sequence on the microstructure and mechanical properties of die-cast Al-11Si-2Cu-Fe alloy10.1016/j.jallcom.2015.07.187 ↗
14. On the preparation and mechanical properties of in situ small-sized TiB2/Al-4.5Cu composites via ultrasound assisted RD method10.1016/j.jallcom.2018.06.303 ↗
15. Ultrasound assisted in-situ casting technique for synthesizing small-sized blocky Al3Ti particles reinforced A356 matrix composites with improved mechanical properties10.1016/j.jallcom.2018.02.010 ↗
16. Microstructures and mechanical properties of nano-C and in situ Al2O3 reinforced aluminium matrix composites processed by equal-channel angular pressing10.1016/j.jallcom.2021.160159 ↗
17. Experimental and thermodynamic study on interfacial reaction of B4C-Al6061 composites fabricated by stir casting process10.1016/j.jallcom.2020.157813 ↗
18. Effect of light weight reinforcement and heat treatment process parameters on morphological and wear aspects of hypoeutectic Al-Si based composites-a critical review10.1016/j.jmrt.2021.10.019 ↗
19. Microstructure and properties of 6111Al matrix composites reinforced by the cooperation of in situ ZrB2 particles and Y10.1016/j.jallcom.2020.154624 ↗
20. Effects of nanosized particles on microstructure and mechanical properties of an aged in-situ TiB2/Al-Cu-Li composite10.1016/j.msea.2018.11.032 ↗
21. A review on fabrication methods, reinforcements and mechanical properties of aluminum matrix composites10.1016/j.jmapro.2020.05.042 ↗
22. Investigation of the influences of ternary Mg addition on the solidification microstructure and mechanical properties of as-cast Al-10Si alloys10.1016/j.msea.2020.140247 ↗
23. Enhancing strength-ductility synergy and mechanisms of Al-based composites by size-tunable in-situ TiB2 particles with specific spatial distribution10.1016/j.compositesb.2021.108912 ↗
24. High performance gravity cast Al9Si0.45Mg0.4Cu alloy inoculated with AlB2 and TiB210.1016/j.jmatprotec.2017.10.028 ↗
25. Heterogeneous microstructure and deformation behavior of an automotive grade aluminum alloy10.1016/j.jallcom.2021.159413 ↗
26. Characterization of externally solidified crystals in a high-pressure die-cast AlSi10MnMg alloy and their effect on porosities and mechanical properties10.1016/j.jmatprotec.2021.117299 ↗
27. Skin solidification during high pressure die casting of Al-11Si-2Cu-1Fe alloy10.1016/S0921-5093(02)00747-5 ↗
28. Effects of Si content on defect band formation in hypoeutectic Al–Si die castings10.1016/j.msea.2005.08.194 ↗
29. Investigation on microstructure heterogeneity of the HPDC AlSiMgMnCu alloy through 3D electron microscopy10.1016/j.matdes.2022.110679 ↗
30. Influence of pore characteristics and eutectic particles on the tensile properties of Al–Si–Mn–Mg high pressure die casting alloy10.1016/j.msea.2020.139280 ↗
31. Macro-heterogeneities in microstructures, concentrations, defects and tensile properties of die cast Al-Mg-Si alloys10.1080/02670836.2017.1334309 ↗
32. Influence of steel preheat temperature and molten casting alloy AlSi9Cu3(Fe) impact speed on wear of X38CrMoV5-1 steel in high pressure die casting conditions10.1016/j.wear.2019.02.008 ↗
33. Development of TiB2 reinforced aluminum foundry alloy based in situ composites – Part II: enhancing the practical aluminum foundry alloys using the improved Al–5 wt%TiB2 master composite upon dilution10.1016/j.msea.2014.03.021 ↗
34. The thickness of defect bands in high-pressure die castings10.1016/j.matchar.2009.06.016 ↗
35. The effects of microstructure heterogeneities and casting defects on the mechanical properties of high-pressure die-cast AlSi9Cu3(Fe) alloys10.1007/s11661-014-2515-7 ↗
36. Effect of as-cast microstructure heterogeneity on aging behavior of a high-pressure die-cast A380 alloy10.1016/j.matchar.2017.11.040 ↗
37. The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy10.1016/j.msea.2021.142544 ↗
38. Segregation band formation in Al-Si die castings10.1007/s11661-004-0236-z ↗
39. Effect of TiB2 and Al3Ti on the microstructure, mechanical properties and fracture behaviour of near eutectic Al-12.6Si alloy10.1007/s12613-020-2070-8 ↗
40. High modulus Al-Si-Mg-Cu/Mg2Si-TiB2 hybrid nanocomposite: microstructural characteristics and micromechanics-based analysis10.1016/j.jallcom.2016.10.016 ↗
41. On the relationship between Vickers hardness and yield stress in Al–Zn–Mg–Cu Alloys10.1016/j.msea.2015.02.073 ↗
42. TiB2 reinforced aluminum based in situ composites fabricated by stir casting10.1016/j.msea.2014.12.033 ↗
43. Toughening of aluminum matrix nanocomposites via spatial arrays of boron carbide spherical nanoparticles10.1016/j.actamat.2015.09.057 ↗
44. Strengthening mechanisms and modelling of mechanical properties of submicron-TiB2 particulate reinforced Al 7075 metal matrix composites10.1016/j.msea.2021.141873 ↗
45. Synergistic strengthening mechanisms of copper matrix composites with TiO2 nanoparticles10.1016/j.msea.2019.138797 ↗
46. Pure Al matrix composites produced by vacuum hot pressing: tensile properties and strengthening mechanisms10.1016/j.msea.2004.05.081 ↗
47. Influence of dislocation–solute atom interactions and stacking fault energy on grain size of single-phase alloys after severe plastic deformation using high-pressure torsion10.1016/j.actamat.2014.01.036 ↗
48. Ultrasound-assisted dispersion of TiB2 nanoparticles in 7075 matrix hybrid composites10.1016/j.msea.2022.142958 ↗
49. Microstructure and mechanical properties of in-situ nano γ-Al2O3p/A356 aluminum matrix composite10.1016/j.jallcom.2019.02.045 ↗
50. Strengthening-toughening of graphene nanoplates and in situ ZrB2 nanoparticles reinforced AA6111 matrix composites with discontinuous layered structures10.1016/j.msea.2022.143750 ↗
51. Microstructure and mechanical properties of an in-situ TiB2/Al-Zn-Mg-Cu-Zr composite fabricated by Melt-SHS process10.1016/j.msea.2018.02.025 ↗
52. Understanding the influencing mechanism of sub-micron sized TiB2p on the microstructures and properties of rheological squeeze casting hypereutectic Al-Si alloys10.1016/j.jmrt.2021.06.048 ↗
53. Enhanced combination of strength and ductility in the semi-solid rheocast hypereutectic Al-Si alloy with the effect of in-situ TiB2 particles10.1016/j.matchar.2021.111143 ↗
54. Microstructure and strengthening mechanism of bimodal size particle reinforced magnesium matrix composite10.1016/j.compositesa.2012.03.007 ↗
55. Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy10.1016/j.matchar.2021.111693 ↗
56. High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB2 particles10.1016/j.msea.2015.03.021 ↗
57. Microstructure study of cold rolling nanosized in-situ TiB2 particle reinforced Al composites10.1016/j.matdes.2017.05.076 ↗
58. Tailoring in-situ TiB2 particulates in aluminum matrix composites10.1016/j.msea.2017.08.047 ↗
59. Effect of electric current pulses on TiB2 particle dispersion in aluminum alloy melt10.1016/j.matlet.2020.127981 ↗
60. Effect of clustering on particle pushing and solidification behaviour in TiB2 reinforced aluminium PMMCs10.1016/j.compositesa.2004.10.027 ↗
61. Mechanical properties of in-situ TiB2/A356 composites10.1016/j.msea.2013.10.021 ↗
62. Effect of heat treatment and Fe content on the microstructure and mechanical properties of die-cast Al-Si-Cu alloys10.1016/j.matdes.2015.07.074 ↗
63. The effect of Mn on particles morphology and property of 5 wt% TiB2/Al-4.5Cu-0.4Mn alloys10.1016/j.jallcom.2022.163907 ↗
64. The superior elevated-temperature mechanical properties of Al-Cu-Mg-Si composites reinforced with in situ hybrid-sized TiCx-TiB2 particles10.1016/j.msea.2018.05.024 ↗
65. Enhancement of mechanical properties in high silicon gravity cast AlSi9Mg alloy refined by Al3Ti3B master alloy10.1016/j.msea.2017.06.005 ↗
66. Tension-compression mechanical behavior and corresponding microstructure evolution of cast A356-T6 aluminum alloy10.1016/j.msea.2021.141613 ↗
67. Nanocrystalline TiC-reinforced H13 steel matrix nanocomposites fabricated by selective laser melting10.1016/j.matdes.2016.02.022 ↗
68. High-performance co-continuous Al-Ce-Mg alloy with in-situ nano-network structure fabricated by laser powder bed fusion