Effect of B4C content and particle sizes on the laser cladded B4C/Inconel 625 composite coatings: Process, microstructure and corrosion property
Source abstract
Abstract
The B4C/Inconel 625 composite coatings were successfully prepared on 20 pipeline steel by laser cladding, in which B4C ceramic was selected as reinforcement phase to improve the microstructure and corrosion property of Inconel 625 coating. The laser cladding parameters were optimized and the effect of B4C content and B4C particle sizes on the microstructure and properties of B4C/Inconel 625 composite coatings were studied in detail. With increasing liner energy density and decreasing powder feeding speed, the crack ratio of the composite coatings reduces. NiB phase forms due to the in-situ reaction of B4C with Ni element in Inconel 625, and a thin layer of planar crystal also forms at the coating/substrate interface. As the addition of B4C content ranged 5wt.%∼10wt.% and the particle sizes ranged 10μm∼60μm, the quantities of equiaxed crystals increase obviously and the coarse columnar crystals are also refined, which contributes to the improved microhardness and corrosion resistance of the B4C/Inconel 625 composite coatings. When the B4C content is 10wt.% and particle size is 10μm, the maximum microhardness of the composite coating is about 567HV0.2, which is 241.2% to that of Inconel 625 coating. The optimal corrosion resistance of B4C/Inconel 625 composite coatings is obtained when the B4C content is 5wt.% and particle size is 60μm.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Titanium Alloys Microstructure and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Top of the line corrosion: causes, mechanisms, and mitigation using corrosion inhibitors10.1016/j.arabjc.2021.103116 ↗
2. Two-dimensional reduced graphene oxide/polypyrrloe-based coating enable superior corrosion protection and photothermal-induced in-situ internal environmental regulation10.1016/j.cej.2023.141481 ↗
3. Efficient preparation of Ni-Fe-SiC pipeline internal surface coating by active/inert metal combined anode jet electrodeposition10.1016/j.jmapro.2023.01.063 ↗
4. Electrodeposition of Ni-W/TiO2 composite coatings on Q345 pipeline steel and their corrosion resistance and Anti-fouling performance in simulated oilfield wastewater
5. Mitigating CO2 corrosion of natural gas steel pipelines by thermal spray aluminum coatings10.5006/3797 ↗
6. Electrochemical behaviour of X80 pipeline steel with alumina coating10.1179/1743294414Y.0000000435 ↗
7. Preparation of Ni-W/PTFE composite coatings on Q345 pipeline steel and their corrosion resistance in simulated oilfield produced water
8. Beam shaping technology and its application in metal laser additive manufacturing: a review10.1016/j.jmrt.2023.08.037 ↗
9. Effect of high-speed laser cladding on microstructure and corrosion resistance of CoCrFeNiMo0.2 high-entropy alloy10.1007/s11771-022-5162-y ↗
10. Experimental study of laser cladding process and prediction of process parameters by artificial neural network (ANN)10.1007/s11771-022-5170-y ↗
11. Microstructure and wear property of WMoTaNb refractory high entropy alloy coating by laser cladding10.1016/j.jmrt.2023.12.082 ↗
12. Effect of phase composition on microstructure and wear resistance of (Al16.80Co20.74Cr20.49Fe21.28Ni20.70)99.5Ti0.5 high-entropy alloy coatings
13. Microstructure and properties of in situ TiC/Ni functionally gradient coatings by powder-fed laser cladding10.1016/j.ceramint.2022.08.243 ↗
14. Parameters optimization for laser cladding of Inconel 625 on ASTM A592 steel10.1016/j.jmrt.2020.05.094 ↗
15. Laser cladding of Inconel 625 wire for corrosion protection10.1016/j.jmatprotec.2014.10.024 ↗
16. Nucleation and strengthening mechanism of laser cladding aluminum alloy by Ni-Cr-B-Si alloy powder based on rare earth control10.1016/j.jmatprotec.2021.117145 ↗
17. Characterization of WC-doped NiCrBSi coatings deposited by Laser Cladding; effects of particle size and content of WC powder10.1016/j.surfcoat.2021.127703 ↗
18. Effect of laser cladding Ti/B4C/dr40-based composite coatings for the surface strengthening of shaft part10.1016/j.optlastec.2022.108721 ↗
19. The effect of Ti and B4C on the microstructure and properties of the laser clad FeCoCrNiMn based high entropy alloy coating
20. Microstructure and mechanical properties of SiC-reinforced Inconel 718 composites fabricated by laser cladding10.1016/j.surfcoat.2023.129514 ↗
21. Fabrication and tribological behaviors of Ti3SiC2/Ti5Si3/TiC/Ni-based composite coatings by laser cladding for self-lubricating applications10.1016/j.optlastec.2020.106077 ↗
22. Microstructure, oxidation resistance and mechanical properties of stellite 12 composite coating doped with submicron TiC/B4C by laser cladding10.1016/j.surfcoat.2020.125810 ↗
23. Microstructure and high-temperature resistance of Al2O3/CoNiCrAlY coatings by laser cladding10.1016/j.ceramint.2023.07.262 ↗
24. Effect of process parameters on microstructure and tribological properties of Ni60A/Cr3C2 laser cladding on 60Si2Mn steel10.1016/j.surfcoat.2023.130005 ↗
25. Laser in-situ preparation and mechanical properties of VC reinforced Fe-based wear-resistant composite cladding10.1016/j.ceramint.2022.06.129 ↗
26. Laser cladding of Ni-base composite coatings onto Ti–6Al–4V substrates with pre-placed B4C+NiCrBSi powders10.1016/j.surfcoat.2005.04.059 ↗
27. Effect of B4C nanoparticles on microstructure and properties of laser cladded IN625 coating10.1016/j.surfcoat.2021.127154 ↗
28. Probing into the properties of B4C reinforced nickel phosphorus-based nanocomposite coating10.1016/j.jmrt.2022.07.184 ↗
29. Effect of the content of B4C on microstructural evolution and wear behaviors of the laser-clad coatings fabricated on Ti6Al4V10.1016/j.optlastec.2015.07.010 ↗
30. Wear and corrosion properties of B4C-added CoCrNiMo high-entropy alloy coatings with in-situ coherent ceramic10.1016/j.matdes.2021.110068 ↗
31. Microstructure, corrosive-wear and electrochemical properties of laser cladded CoCrFeNiMo-B4C coatings in 3.5%NaCl solution10.1016/j.optlastec.2022.108999 ↗
32. WC distribution, microstructure evolution mechanism and microhardness of a developed Ti-6Al-4 V/WC MMC coating fabricated by laser cladding10.1016/j.optlastec.2022.108232 ↗
33. Influence of particle size on laser absorption and scanning track formation mechanisms of pure tungsten powder during selective laser melting10.1016/j.eng.2019.07.003 ↗
34. Study on crack behavior of laser cladding ceramic-metal composite coating with high content of WC10.1016/j.ceramint.2022.03.010 ↗
35. Effect of laser cladding on forming microhardness and tensile strength of YCF101 alloy powder in the different full lap joint modes10.1016/j.jallcom.2019.04.046 ↗
36. Microstructure evolution, mechanical properties, and strengthening mechanism of TiC reinforced Inconel 625 nanocomposites fabricated by selective laser melting10.1016/j.msea.2020.139655 ↗
37. High-efficiency fabrication of Inconel 625 coating for AISI 1045 carbon steel through laser cladding with hot wire: microstructure and wear resistance10.1016/j.jmapro.2023.07.063 ↗
38. In situ SEM study on tensile fractured behavior of Al/steel laser welding-brazing interface10.1016/j.matdes.2022.111320 ↗
39. A study on the influence of reinforcement particle size in laser cladding of TiC/Inconel 625 metal matrix composite10.1016/j.optlastec.2023.109115 ↗
40. Study on tribological oxide mechanism of CoCrFeNiMo high entropy alloy
41. Microstructure and corrosion property of TC4 coating with Al0.5CoCrFeNi high-entropy alloy interlayer by laser cladding10.1016/j.surfcoat.2023.130190 ↗
42. Phase composition and microstructure of B4C particles reinforced aluminum matrix composites fabricated via direct laser deposition10.1007/s10853-023-09293-7 ↗
43. Microscopic morphology and distribution of TiC phase in laser clad NiCrBSiC–TiC layer on titanium alloy substrate10.1016/S0257-8972(02)00006-3 ↗
44. Tribology comparison of laser-cladded CrMnFeCoNi coatings reinforced by three types of ceramic (TiC/NbC/B4C)10.1016/j.surfcoat.2022.129013 ↗
45. Microstructural control in metal laser powder bed fusion additive manufacturing using laser beam shaping strategy10.1016/j.actamat.2019.11.053 ↗
46. Effect of Y2O3 on the microstructure and tribology property of WMoTaNb refractory high entropy alloy coating prepared by laser cladding10.1016/j.ijrmhm.2023.106273 ↗
47. Deformation mechanisms in ultrafine-grained metals with an emphasis on the Hall–Petch relationship and strain rate sensitivity10.1016/j.jmrt.2021.06.016 ↗
48. Comparison of CoCrFeNi coatings prepared via high-speed laser cladding and normal laser cladding on microstructure and properties10.1016/j.intermet.2022.107795 ↗
49. Effect of Y2O3 on microstructure and properties of CoCrFeNiTiNb high entropy alloy coating on Ti–6Al–4V surface by laser cladding10.1016/j.jre.2023.02.015 ↗
50. Role of Cr in the high-temperature oxidation behavior of CrxMnFeNi high-entropy alloys at 800 °C in air10.1016/j.corsci.2022.110211 ↗