journal article·2021-11Open access

An experimental and theoretical investigation of the effect of second-phase particles on grain growth during the annealing of hot-rolled AZ61 magnesium alloy

M. Mohseni, A.R. Eivani, H. Vafaeenezhad, H.R. Jafarian, M.T. Salehi, J. Zhou

Abstract

The mechanical properties of a magnesium alloy strongly depend on its grain structure. It is desirable to minimize grain growth during the post-forming annealing treatment, thereby minimizing the loss in strength while regaining ductility. In the present research, the annealing of the hot-rolled AZ61 Mg alloy at different temperatures for different times was performed to reveal the kinetics of grain growth, as affected by the precipitation or dissolution of second-phase particles. Three approaches, i.e., experimental, analytical modeling and atomistic simulation were taken and the results were compared. The predictions made from the analytical model and Monte Carlo simulation were both in acceptable agreement with experimental results in terms of the resultant grain sizes. However, the Monte Carlo simulation showed advantages over the analytical model. It was found that with increasing annealing temperature and holding time, the fraction of second-phase particles reduced, which strongly affected the kinetics of grain growth, limiting grain size and grain size homogeneity. The average grain sizes and the largest grain sizes were both taken as the characteristic parameters of the as-annealed microstructure. The results pointed out the importance of choosing an appropriate combination of annealing temperature and time in order to retain second-phase particles during annealing not only for preventing unrestricted grain growth but also for avoiding grain size inhomogeneity.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Magnesium castings for automotive applications
2. Magnesium: properties—applications—potential10.1016/S0921-5093(00)01351-4 ↗
3. Strain-rate sensitivity and microstructural evolution in a Mg–Al–Zn alloy10.1016/j.scriptamat.2010.06.047 ↗
4. Modeling the temperature dependent effect of twinning on the behavior of magnesium alloy AZ31B sheet10.1016/j.msea.2006.03.160 ↗
5. Compressive strain-rate sensitivity of magnesium–aluminum die casting alloys10.1016/j.matdes.2008.05.050 ↗
6. Instantaneous strain rate sensitivity of wrought AZ31 magnesium alloy10.1016/j.matdes.2013.01.068 ↗
7. Dynamic evolution of new grains in magnesium alloy AZ31 during hot deformation10.2320/matertrans.44.197 ↗
8. Microstructural development during hot working of Mg-3Al-1Zn10.1007/s11661-007-9207-5 ↗
9. Microstructure refining and property improvement of ZK60 magnesium alloy by hot rolling10.1016/S1003-6326(11)61585-9 ↗
10. Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK6010.1016/S1359-6454(01)00020-9 ↗
11. Dynamic recrystallisation and the development of microstructure during the high temperature deformation of magnesium10.1016/0001-6160(82)90031-1 ↗
12. Humphreys · 2012
13. Influence of twinning on the grain refinement during high-temperature deformation in a magnesium alloy10.1016/j.scriptamat.2010.11.009 ↗
14. A microstructure study on an AZ31 magnesium alloy tube after hot metal gas forming process10.1007/s11665-007-9062-y ↗
15. Computer simulation of grain growth—I. Kinetics10.1016/0001-6160(84)90151-2 ↗
16. Computer simulation of grain growth—IV. Anisotropic grain boundary energies10.1016/0001-6160(85)90093-8 ↗
17. Computer simulation of grain growth—II. Grain size distribution, topology, and local dynamics10.1016/0001-6160(84)90152-4 ↗
18. Computer simulation of grain growth-III. Influence of a particle dispersion10.1016/0001-6160(84)90089-0 ↗
19. On abnormal subgrain growth and the origin of recrystallization nuclei10.1016/S1359-6454(03)00079-X ↗
20. Grain-boundary diffusion creep in nanocrystalline palladium by molecular-dynamics simulation10.1016/S1359-6454(01)00329-9 ↗
21. Simulation of normal grain growth by cellular automata10.1016/1359-6462(96)00055-3 ↗
22. On the theory of normal and abnormal grain growth10.1016/0001-6160(65)90200-2 ↗
23. Computer simulation of grain growth with second phase particle pinning10.1016/S1359-6454(97)00048-7 ↗
24. On the theory of the effect of precipitate particles on grain growth in metals
25. Monte Carlo simulation of grain refinement during friction stir processing10.1007/s10853-020-04963-2 ↗
26. Review on dynamic recrystallization of martensitic stainless steels during hot deformation: Part I—experimental study10.3390/met11040572 ↗
27. Hot workability analysis of AZ61 Mg alloys with processing maps10.1016/j.msea.2014.04.017 ↗
28. Growth mechanism of extension twin variants during annealing of pure magnesium: an ‘ex situ’ electron backscattered diffraction investigation10.1016/j.matchar.2017.02.008 ↗
29. Grain growth in multiple scales of polycrystalline AZ31 magnesium alloy by phase-field simulation10.1007/s11661-012-1478-9 ↗
30. Simulation of dynamic recrystallization process during friction stir welding of AZ91 magnesium alloy10.1007/s00170-015-7595-z ↗
31. Structural properties and enthalpy of formation of magnesium hydride from quantum Monte Carlo calculations10.1103/PhysRevB.77.104103 ↗
32. The Monte Carlo simulation of microstructural evolution in metals10.1016/S0921-5093(97)80019-6 ↗
33. Effect of yttrium on corrosion behavior of extruded AZ61 Mg alloy10.1016/j.jma.2015.11.008 ↗
34. Influence of Pd addition on the creep behavior of AZ61 magnesium alloy10.1016/j.msea.2011.04.005 ↗
35. Effect of second-phase particles on grain growth in calcite10.1111/j.1151-2916.1986.tb07374.x ↗
36. Investigation of limiting grain size and microstructure homogeneity in the presence of second phase particles using the Monte Carlo method10.1016/j.jmatprotec.2007.04.132 ↗
37. Hybrid Monte Carlo–Finite element simulation of microstructural evolution during annealing of severely deformed Sn-5Sb alloy10.1016/j.commatsci.2019.03.030 ↗
38. A more accurate three-dimensional grain growth algorithm10.1016/j.actamat.2011.07.052 ↗
39. Recrystallization and grain growth in hot rolling10.1179/msc.1979.13.3-4.187 ↗