journal article·2024-03Open access

Predictive tools for the cooling rate-dependent microstructure evolution of AISI 316L stainless steel in additive manufacturing

Amirreza Abdali, Syamak Hossein Nedjad, Habib Hamed Zargari, Abdollah Saboori, Mehmet Yildiz

Abstract

This study presents a through evaluation of advanced predictive tools for the solidification microstructure of AISI 316L stainless steel, taking into account both accounting for both chemical composition and cooling rate. In order to achieve a broad range of cooling rates comparable to prominent additive manufacturing processes, autogenous laser welds were carried out on the steel plate by means of powderless directed energy deposition (DED) and selective laser melting (SLM) machines. Computational analysis of cooling rates and metallographic investigations revealed that DED welds solidify at moderate rates, exhibiting a primary ferrite (FA) solidification mode. Conversely, SLM welds solidify at significantly higher rates, showing dual solidification modes: initial austenite (A) at the fusion boundary and subsequent ferrite (F) at the interior. The WRC-1992 constitution diagram predicts the FA mode in accordance with the findings in the DED welds. An implicated Schaeffler diagram, proposed for a comparable cooling rate, also predicts the same mode. An artificial neural network model, referred to as ORFN, consistently predicts the variation of ferrite content within the DED welds based on the cooling rate variation. The dual mode observed in the SLM welds aligns with established knowledge regarding the alteration of stainless steel solidification under extremely high cooling rates. While the occurrence of the A mode at the fusion boundary is anticipated according to implicated Schaeffler diagrams for extremely high cooling rates, the transition to the F mode is not addressed explicitly.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Davis · 1994
2. Powder bed based laser additive manufacturing process of stainless steel: a review10.1016/j.matpr.2018.06.193 ↗
3. Steels in additive manufacturing: a review of their microstructure and properties10.1016/j.msea.2019.138633 ↗
4. Additive manufacturing of steels: a review of achievements and challenges10.1007/s10853-020-05109-0 ↗
5. Wire Arc additive manufacturing of stainless steels: a review10.3390/app10051563 ↗
6. Microstructure, solidification texture, and thermal stability of 316 L stainless steel manufactured by laser powder bed fusion10.3390/met8080643 ↗
7. Conventional and additively manufactured stainless steels: a review10.1007/s12666-021-02305-7 ↗
8. Weldability and weld performance of candidate austenitic alloys for advanced ultrasupercritical fossil power plants10.1179/1362171814Y.0000000197 ↗
9. Microstructural development and solidification cracking susceptibility of austenitic stainless steel welds10.1179/imr.1991.36.1.16 ↗
10. Recent developments in stainless steels10.1016/j.mser.2009.03.001 ↗
11. Kou · 2020
12. Lippold · 2005
13. Effect of solidification conditions on the solidification mode in austenitic stainless steels10.1007/BF02651615 ↗
14. Constitution diagram for stainless steel weld metal
15. Ferrite in austenitic stainless steel weld metal
16. Kotecki · 1992 · 171s
17. Prediction of austenitic weld metal microstructure and properties
18. Predictive and measurement methods for delta ferrite determination in stainless steels
19. Improved ferrite number prediction in stainless steel arc welds using artificial neural networks - Part 1: neural network development
20. Improved ferrite number prediction in stainless steel arc welds using artificial neural networks - Part 2: neural network results
21. Prediction of ferrite number in stainless steel welds using Bayesian Neural Network model10.1007/BF03266582 ↗
22. Microstructural development during solidification of stainless steel alloys10.1007/BF02650298 ↗
23. Effects of rapid solidification by laser surface melting on solidification modes. Study on laser surface modification of stainless steels10.2207/qjjws.7.414 ↗
24. Microstructural modification of austenitic stainless steels by rapid solidification10.1007/BF02645553 ↗
25. Microstructural origin of the skeletal ferrite morphology of austenitic stainless steel welds10.1007/BF02664809 ↗
26. Solidification microstructure of laser welded stainless steels
27. Effect of rapid solidification on stainless steel weld metal microstructures and its implications on the Schaeffler diagram
28. Prediction of the δ to γ transition in austenitic stainless steels during laser treatment10.2355/isijinternational.38.71 ↗
29. Solidification behavior and cracking susceptibility of pulsed-laser welds in austenitic stainless steels
30. Improved weldability diagram for pulsed laser welded austenitic stainless steels10.1179/136217103225008847 ↗
31. Prediction of weld metal microstructure: stainless steels10.1080/09507119209548301 ↗
32. Improved ferrite number prediction model that accounts for cooling rate effects - Part 1: model development
33. Improved ferrite number prediction model that accounts for cooling rate effects - Part 2: model results
34. Resistance spot welding joints of AISI 316L austenitic stainless steel sheets: phase transformations, mechanical properties and microstructure characterizations10.1016/j.matdes.2014.04.075 ↗
35. Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition10.1016/j.jmatprotec.2016.09.005 ↗
36. Effect of build geometry and orientation on microstructure and properties of additively manufactured 316L stainless steel by laser metal deposition10.1016/j.mtla.2019.100359 ↗
37. An investigation on the effect of powder recycling on the microstructure and mechanical properties of AISI 316L produced by Directed Energy Deposition10.1016/j.msea.2019.138360 ↗
38. Characterisation of porosity, density, and microstructure of directed energy deposited stainless steel AISI 316L
39. Solidification behaviour of austenitic stainless steels during welding and directed energy deposition10.1080/13621718.2022.2115664 ↗
40. Heterogeneity and solidification pathways in additively manufactured 316L stainless steels10.1007/s11661-022-06747-6 ↗
41. Physics-informed machine learning and mechanistic modeling of additive manufacturing to reduce defects
42. Metallurgy, mechanistic models and machine learning in metal printing10.1038/s41578-020-00236-1 ↗
43. Mechanistic models for additive manufacturing of metallic components10.1016/j.pmatsci.2020.100703 ↗
44. Harnessing the scientific synergy of welding and additive manufacturing10.1080/13621718.2019.1615189 ↗
45. Microstructure and mechanical properties of AISI 316L produced by directed energy deposition-based additive manufacturing: a review10.3390/app10093310 ↗
46. Microstructure and mechanical properties of 316L austenitic stainless steel processed by different SLM devices10.1007/s00170-020-05371-1 ↗
47. Impact of the allowed compositional range of additively manufactured 316L stainless steel on processability and material properties10.3390/ma14154074 ↗
48. Mechanism of keyhole formation and stability in stationary laser welding10.1088/0022-3727/35/13/320 ↗
49. Effect of workpiece vibration frequency on heat distribution and material flow in the molten pool in tandem-pulsed gas metal arc welding
50. A comprehensive comparison of the analytical and numerical prediction of the thermal history and solidification microstructure of inconel 718 products made by laser powder-bed fusion10.1016/J.ENG.2017.05.023 ↗
51. Numerical modeling of melt-pool behavior in selective laser melting with random powder distribution and experimental validation10.1016/j.jmatprotec.2017.11.032 ↗
52. Numerical simulation of spatter formation during fiber laser welding of 5083 aluminum alloy at full penetration condition10.1016/j.optlastec.2017.10.010 ↗
53. Micro pool characteristics of 316L and the influence of sulfur during SLM10.1016/j.optlastec.2021.107136 ↗