journal article·2024-05Open access

Electrodeposition of nanocrystalline Ni and NiCr alloy coatings: Effects of Cr content on microhardness and wear resistance improvement

Zhan Liu, Qicheng Zhang, Xingwen Zhang, Zhifei Yu, Xiaowei Zhang, Qingzhong Mao, Jinfeng Nie, Yonghao Zhao

Abstract

The safety and reliability of high-speed trains depend on the brake disc. In order to improve the lifetime of brake disc and reduce the waste of resources, a coating with higher microhardness and well wear resistance is urgently needed. The effect of chromium content on the microstructure, microhardness and wear resistance of NiCr coating has been studied. Nano-crystalline Ni and NiCr coatings with superior mechanical properties were successfully prepared on the 30CrNiMo steel substrate by pulse current electrodeposition method. The inclusion of formic acid and sodium citrate was found to significantly expedite the co-deposition of Ni and Cr. The NiCr coatings with various Cr contents were prepared at current densities ranging from 200-300 mA/cm2. These coatings significantly enhance microhardness and wear resistance of the substrate. The microhardness of the NiCr coating increased to 603 HV, outperforming pure Ni coating by 119 HV. Additionally, the wear rate of the NiCr coating decreased by 50% at a load of 10 N in comparison to the Ni coating. The high microhardness is attributed to grain refinement and solution strengthening. This study successfully addresses the challenges associated with electrodepositing Ni-based coatings on 30CrNiMo steel substrate and lays a theoretical foundation for the utilization of Ni-based coatings to enhance the tribological properties of materials used in high-speed train brake disc.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Electrodeposition and Electroless Coatings · Lubricants and Their Additives · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Airborne wear particle emission from train brake friction materials with different contents of steel and copper fibres
2. Effect of tool tilt angle on microstructure, mechanical properties and fracture behavior of dissimilar friction stir lap welding joint of SiCp/ZL101 and ZL10110.1016/j.jmrt.2023.02.094 ↗
3. Friction-induced vibration and noise characteristics, and interface tribological behavior during high-speed train braking: the effect of the residual height of the brake pad friction block
4. Surface modified NiTi smart biomaterials: surface engineering and biological compatibility
5. Electrospark deposition of wear and corrosion resistant Ta(Zr)C-(Fe,Mo,Ni) coatings to protect stainless steel from tribocorrosion in seawater
6. Effect of carburizing process on high cycle fatigue behavior of 18CrNiMo7-6 steel10.1016/j.jmrt.2021.12.074 ↗
7. Characterization, wear and emission properties of MnS containing laser cladded brake disc
8. Surface modification to improve properties of materials10.3390/ma12030441 ↗
9. Effect of different heat-treated temperatures upon structural and abrasive performance of Ni-TiN composite nanocoatings10.1016/j.jmrt.2023.10.173 ↗
10. Preparation and tribological properties of NiCr–Mo–Ag–O/Mo–V–Ag–O bilayer film at RT-1000 °C10.1016/j.jmrt.2023.07.207 ↗
11. Designing hard, low-refractive-index lossy materials for super wear-resistant absorbers10.1080/21663831.2022.2055436 ↗
12. Novel application of nanocrystalline nickel electrodeposit: making good diamond tools easily, efficiently and economically10.1016/j.surfcoat.2006.10.047 ↗
13. CeO2 nanoparticles decorated on porous Ni–Fe bimetallic phosphide nanosheets for high-efficient overall water splitting10.1080/21663831.2022.2131372 ↗
14. Characterization of electrodeposited Ni–Cr/hBN composite coatings10.1016/j.jallcom.2020.155511 ↗
15. A facile and cost-effective practical approach to develop clinical applications of NiTi: fenton oxidation process10.1080/00202967.2020.1802104 ↗
16. Optimization of electrodeposition nanocrytalline Ni-Fe alloy coatings for the replacement of Ni coatings10.1016/j.jallcom.2022.163761 ↗
17. Electrodeposition and mechanical and corrosion resistance properties of Ni–W/SiC nanocomposite coatings10.1016/j.matlet.2006.04.007 ↗
18. Feasible strategies for promoting the mechano-corrosion performance of Ni-Co based coatings: which one is better?10.1016/j.surfcoat.2021.127337 ↗
19. Evaluation of TiO2 nanoparticles concentration and applied current density role in determination of microstructural, mechanical, and corrosion properties of Ni–Co alloy coatings10.1134/S2070205120020215 ↗
20. Heterostructured NiCr matrix composites with high strength and wear resistance10.1016/j.jmst.2021.06.076 ↗
21. Hot corrosion performance of a NiCr coated Ni-based alloy10.1016/j.scriptamat.2006.03.054 ↗
22. Cyclic oxidation behavior of selected commercial NiCr-alloys for engine exhaust valves in wet air environment between 800 and 950 °C10.1016/j.corsci.2022.110817 ↗
23. Electrodeposition and characterization of amorphous Fe-Ni-Cr-based alloys10.1007/BF00249658 ↗
24. Fabrication and wear properties of co-deposited Ni-Cr nanocomposite coatings10.1016/S1003-6326(09)60104-7 ↗
25. Electrodeposited Ni-Cr and Ni-Cr-P alloys10.1149/1.2069401 ↗
26. Mechanistic study of Ni–Cr–P alloy electrodeposition and characterization of deposits10.1016/j.jelechem.2021.115582 ↗
27. Biosorption of Chromium(VI) from Aqueous solutions by green algae spirogyra species10.1016/S0043-1354(01)00138-5 ↗
28. Eco-toxicity of hexavalent chromium and its adverse impact on environment and human health in Sukinda Valley of India: a review on pollution and prevention strategies10.1016/j.enceco.2023.01.002 ↗
29. Electrodeposition and characterization of Ni–Cr alloy coating10.1149/1.2161527 ↗
30. State-of-the-art in surface integrity in machining of nickel-based super alloys10.1016/j.ijmachtools.2015.10.001 ↗
31. State of art for sustainable machining of nickel-based alloys using coated and uncoated tools and machining of high strength materials using surface modified cutting tools10.1016/j.triboint.2022.107517 ↗
32. Structure characterization and tribological properties of thick chromium coating electrodeposited from a Cr(III) electrolyte10.1016/j.surfcoat.2012.12.021 ↗
33. Experimental investigations and effects studies on electrodeposited Ni-Cr composite coating using robust design approach10.1016/j.matpr.2017.11.363 ↗
34. Characterization and corrosion behavior of Ni-Cr coatings by using pulse current electrodeposition10.1108/ACMM-04-2023-2788 ↗
35. Ni-Cr alloy electrodepositing technology on Fe substrate and coating performance10.1007/s11771-007-0036-x ↗
36. Corrosion and tribological behavior of Ni–Cr alloy coatings electrodeposited on low carbon steel in Cr (III)–Ni (II) bath10.1016/j.surfcoat.2015.10.006 ↗
37. The use of XPS for study of the surface layers of CrNi alloys electrodeposited from the Cr(III)+Ni(II) bath10.1016/j.apsusc.2012.06.048 ↗
38. Chromium electrodeposition from Cr(III) aqueous solutions10.1016/j.surfcoat.2011.02.027 ↗
39. Electrochemical study of the passive behaviour of Ni–Cr alloys in a borate solution—a mixed-conduction model approach10.1016/S0022-0728(01)00423-5 ↗
40. Ni-Cr alloy electrodeposition
41. Influencing factors on Cr content in Ni-Cr deposit
42. Study of nickel-chromium electrodeposit
43. Electrodeposition of Ni-Cr alloy on aluminum substrate10.1007/s11771-006-0134-1 ↗
44. Corrosion behavior and microstructure of electrodeposited nano-layered Ni–Cr coatings10.1016/j.tsf.2015.10.046 ↗
45. Hardness variation and corrosion behavior of as-plated and annealed Cr–Ni alloy deposits electroplated in a trivalent chromium-based bath10.1016/j.surfcoat.2009.05.047 ↗
46. Pulse reversal plating of nickel and nickel alloys for microgalvanics10.1016/S0013-4686(01)00578-3 ↗
47. Pulse electrodeposition and corrosion properties of nanocrystalline nickel-chromium alloy coatings on copper substrate10.1016/j.jallcom.2020.153712 ↗
48. Post-deposition crack evolution in Cr(III) alloy electrodeposits: phenomenology10.1016/j.surfcoat.2020.126648 ↗
49. Electrolytically deposited hardchrome10.1016/S0257-8972(96)02973-8 ↗
50. Pulse-reverse electroplating of chromium from Sargent baths: influence of anodic time on physical and electrochemical properties of electroplated Cr10.1016/j.ijrmhm.2020.105213 ↗
51. Corrosion behaviour of chromium coatings obtained by direct and reverse pulse plating electrodeposition in NaCl aqueous solution10.1016/j.corsci.2013.10.005 ↗
52. Lattice parameter studies of structure changes of Ni-Cr alloys in the region of Ni2Cr10.1016/0025-5416(82)90119-7 ↗
53. Corrosion resistance of multilayer coatings of nanolayered Cr/Ni electrodeposited from Cr(III)–Ni(II) bath10.1016/j.tsf.2012.03.127 ↗
54. The scherrer formula for X-ray particle size determination10.1103/PhysRev.56.978 ↗
55. Significant improvement of the room and cryogenic mechanical properties of an AlN particle reinforced Al matrix composite by alloying element magnesium10.1016/j.compositesb.2023.111056 ↗
56. On the extrinsic Hall-Petch to inverse Hall-Petch transition in nanocrystalline Ni-Co electrodeposits10.1016/j.scriptamat.2022.114799 ↗
57. Effect of interstitial carbon on the mechanical properties of electrodeposited bulk nanocrystalline Ni10.1016/j.actamat.2013.02.025 ↗
58. Exploration of electrodeposited process of Ni-Co-Cr coating and investigation of Cr doping strengthening mechanism by indentation simulation10.1016/j.jmatprotec.2022.117818 ↗
59. Hall–Petch breakdown manifested in abrasive wear resistance of nanocrystalline nickel10.1016/S1359-6462(02)00062-3 ↗
60. Effect of the pulse plating parameters on the mechanical properties of nickel electrodeposits10.1016/j.surfcoat.2012.09.027 ↗