journal article·2023-03Open access

Mechanical properties and microscopic characterization of cemented paste backfill with electrolytic manganese residue matrix binder

Gujian Wang, Qi Sun, Chunxiao Qi, Lang Liu, Yi Tan, Lijuan Su

Abstract

With the exploitation of mineral resources, more and more mined-out areas need to be backfilled. In order to meet the needs of backfill, a new cemented paste backfill (CPB) is developed. The new material uses electrolytic manganese residue (EMR), slag and red mud as binder, tailings as aggregates, and sodium hydroxide as alkali activator. Taking the EMR content, the mass concentration and bone glue ratio as the influencing factors, the unconfined compressive strength (UCS) of 3 d, 7 d and 28 d as the target, the single factor design was carried out, and the mixture proportion recommended was obtained. According to the 28 d UCS of CPB under mixture proportion recommended, a piecewise damage constitutive model with the end of initial compaction stage as the critical point was established. The three microscopic test methods of scanning electron microscopy–energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) were used to analyze the CPB at different ages under the mixture proportion recommended. The internal morphology, composition, phase composition and chemical bond combination of the CPB were analyzed. The results show: when the EMR content is 20%, the mass concentration is 81%, and the bone glue ratio is 6, the mixture proportion recommended for the developed CPB was recommended; The established constitutive model can fit the UCS curve well; At the initial stage of reaction, C–S–H and C-A-S-H gels were formed inside the CPB; With the increase of age, the amount of gel formation increased, the diffraction peak of the reactants weakened, the diffraction peak of the product enhanced, the pore played a filling role, so that the internal structure was dense, porosity decreased; The corresponding characteristic bands originate from the asymmetric stretching and bending vibrations of H–O–H, Si–O, Si–O–Si, C–O and O–H chemical bonds. This new type of CPB can well meet the requirements of backfill, and can reasonably use solid waste.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Tailings Management and Properties · Concrete and Cement Materials Research · Rock Mechanics and Modeling

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Solidification and kinetics of Mñ(2+) in electrolytic manganese residue
2. Development status and trend of paste technology in China
3. Synergistic use of electrolytic manganese residue and barium slag to prepare belite-sulphoaluminate cement study10.1016/j.conbuildmat.2022.126672 ↗
4. Study of localized deformation in geopolymer cemented coal gangue-fly ash backfill based on the digital speckle correlation method10.1016/j.conbuildmat.2019.04.208 ↗
5. Preparation and microstructure of fly ash geopolymer paste backfill material10.1016/j.jclepro.2019.03.310 ↗
6. Performance optimization and characterization of loess-slag-based geopolymer composite: a new sustainable green material for backfill10.1016/j.conbuildmat.2022.129103 ↗
7. Alkali activation of blast furnace slag using a carbonate-calcium carbide residue alkaline mixture to prepare cemented paste backfill10.1016/j.conbuildmat.2021.126234 ↗
8. Flow ability of cemented paste backfill with chloride-free antifreeze additives in sub-zero environments10.1016/j.cemconcomp.2021.104359 ↗
9. High-efficiency utilization of limestone tailings: used as binder and fine aggregate to prepare karst structure filling material10.1016/j.conbuildmat.2021.125841 ↗
10. Enhancing the sustainable immobilization of phosphogypsum by cemented paste backfill with the activation of γ-Al2O310.1016/j.conbuildmat.2022.128624 ↗
11. Viscosity enhancement of self-consolidating cement-tailings grout by biomass fly ash vs. chemical admixtures10.1016/j.conbuildmat.2022.127802 ↗
12. Mechanical properties and deformation mechanism of stratified cemented tailings backfill under unconfined compression10.1016/j.conbuildmat.2022.127205 ↗
13. Effect of microbial-cemented on mechanical properties of iron tailings backfill and its mechanism analysis10.1016/j.conbuildmat.2021.126001 ↗
14. Curing stress effect on stability, microstructure, matric suction and electrical conductivity of cementitious tailings backfills10.1016/j.conbuildmat.2022.129601 ↗
15. Effects of mineral additives and age on microstructure evolution and durability properties of sand-reinforced cementitious mine backfills10.1016/j.conbuildmat.2022.129079 ↗
16. Characterization of early age behavior of cemented paste backfill through the magnitude and frequency spectrum of ultrasonic P-wave10.1016/j.conbuildmat.2020.118733 ↗
17. Flexural behavior of fiber reinforced cemented tailings backfill under three-point bending10.1109/ACCESS.2019.2943479 ↗
18. Influence of solid content, cement/tailings ratio and curing time on rheology and strength of cemented tailings backfill10.3390/min10100922 ↗
19. Preparation of mine backfilling from steel slag-based non-clinker combined with ultra-fine tailing10.1016/j.conbuildmat.2021.126248 ↗
20. Strength demand of cemented backfill guided by backfilling ratio control in coal mines
21. Comprehensive particle size characterization method for complex filling tailings using singular value decomposition
22. Strength and damage characteristics of tailings filling body with different particle size distributions
23. Damage mechanism and constitutive model of surface paste disposal of a coal mine collapsed pit in a complicated environment10.1016/j.conbuildmat.2021.124637 ↗
24. Development of high-strength geopolymers from red mud and blast furnace slag
25. A review of the sustainable utilisation of red mud and fly ash for the production of geopolymer composites10.1016/j.conbuildmat.2022.128892 ↗
26. Ding · 2021
27. Long · 2020
28. Zhao · 2008
29. Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram Na2O–CaO–Al2O3–SiO2–H2O10.1016/j.cemconres.2011.05.006 ↗
30. Effect of Ca /Si ratio on the formation and characteristics of synthetic aluminosilicate hydrate gels
31. Effect of alkalis on fresh C–S–H gels. FTIR analysis10.1016/j.cemconres.2009.01.003 ↗
32. Setting acceleration and strength enhancement derived from calcium species for alkali-activated cementitious materials
33. Modification of glass structure via CaO addition in granulated copper slag to enhance its pozzolanic activity10.1016/j.conbuildmat.2019.117970 ↗
34. Cementitious property of NaAlO2-activated Ge slag as cement supplement10.1007/s12613-019-1901-y ↗
35. Use of glass waste as an activator in the preparation of alkali-activated slag. Mechanical strength and paste characterisation10.1016/j.cemconres.2013.12.005 ↗
36. Study on the hydration mechanism of a hardened slag-based plugging agent activated by alkalis10.1016/j.conbuildmat.2019.01.015 ↗
37. Property and cementation mechanism of alkali-activated coal gangue-slag cementitious materials
38. Effect of calcium hydroxide on the alkali-silica reaction of alkali-activated slag mortars activated by sodium hydroxide10.1016/j.conbuildmat.2020.121868 ↗
39. Alternative alkali-activator from steel-making waste for one-part alkali-activated slag10.1016/j.jclepro.2020.123020 ↗