journal article·2023-11Open access

Grain size dependent mechanical properties of CoCrFeMnNi high-entropy alloy investigated by shear punch testing

Mohammad Javad Sohrabi, Hamed Mirzadeh, Abdol Reza Geranmayeh, Reza Mahmudi

Abstract

The effect of grain size on the mechanical properties of an equiatomic CoCrFeNiMn high-entropy alloy (HEA) was investigated by shear punch testing (SPT) and Vickers hardness measurements. A Hall–Petch relationship was developed for the dependency of shear yield stress (SYS) on the average grain size (D). The correlation of the SYS and ultimate shear strength (USS) to the tensile yield stress (TYS) and ultimate tensile strength (UTS) values were also studied. A wide range of grain sizes was obtained by the thermomechanical processing of cold rolling and elevated-temperature annealing, where the primary recrystallization and grain growth phenomena were used for grain refinement and grain coarsening, respectively. Based on the obtained results and literature data, the Hall–Petch relationships of SYS = 88.9 + 301.1/√D and TYS = 167 + 520/√D were proposed, respectively. Moreover, the relationships of TYS = 1.76 × SYS and UTS = 1.33 × USS were obtained, where the former is in excellent agreement with the von Mises yield criterion based on the plasticity theory, and the latter is influenced by the work-hardening behavior of the material and dynamic phenomena during plastic deformation.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High Entropy Alloys Studies · High Temperature Alloys and Creep · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. Cantor-derived medium-entropy alloys: bridging the gap between traditional metallic and high-entropy alloys10.1016/j.jmrt.2022.01.118 ↗
2. Mechanical properties of high-entropy alloys with emphasis on face-centered cubic alloys10.1016/j.pmatsci.2018.12.003 ↗
3. Processing, alloy composition and phase transition effect on the mechanical and corrosion properties of high entropy alloys: a review10.1016/j.jmrt.2016.03.004 ↗
4. Post-processing of additively manufactured high-entropy alloys-A review10.1016/j.jmrt.2022.11.027 ↗
5. Gao · 2016
6. Effect of grain size on the tribological behavior of CoCrFeMnNi high entropy alloy10.3390/ma16041714 ↗
7. Influence of plastic deformation on the corrosion behavior of CrCoFeMnNi high entropy alloy10.1016/j.jallcom.2021.161822 ↗
8. A novel Fe-rich non-equiatomic medium-entropy alloy with superior mechanical properties10.1016/j.jallcom.2023.170029 ↗
9. Multicomponent high-entropy Cantor alloys10.1016/j.pmatsci.2020.100754 ↗
10. Mechanical properties of Cantor alloys driven by additional elements: a review10.1016/j.jmrt.2021.09.019 ↗
11. Effect of second phase particles on mechanical properties and grain growth in a CoCrFeMnNi high entropy alloy10.1016/j.msea.2019.01.112 ↗
12. Unveiling the strengthening mechanisms of as-cast micro-alloyed CrMnFeCoNi high-entropy alloys10.1016/j.jallcom.2023.170443 ↗
13. Superplasticity of high-entropy alloys: a review10.1007/s43452-021-00344-x ↗
14. The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy10.1016/j.actamat.2013.06.018 ↗
15. Enhanced strength and ductility of bulk CoCrFeMnNi high entropy alloy having fully recrystallized ultrafine-grained structure10.1016/j.matdes.2017.07.054 ↗
16. Temperature dependence of the Hall–Petch relationship in CoCrFeMnNi high-entropy alloy10.1016/j.jallcom.2019.07.357 ↗
17. Effect of Fe on the Hall-Petch relationship of (CoCrMnNi) 100-x Fex medium-and high-entropy alloys10.1016/j.intermet.2021.107239 ↗
18. Grain size tailoring to control strain hardening and improve the mechanical properties of a CoCrFeNiMn high-entropy alloy
19. Twenty years of the CoCrFeNiMn high-entropy alloy: achieving exceptional mechanical properties through microstructure engineering10.1016/j.jmrt.2023.01.181 ↗
20. Evaluation of mechanical properties using shear–punch testing10.1016/j.msea.2004.12.048 ↗
21. Superplasticity of a fine-grained Mg–9Gd–4Y–0.4 Zr alloy evaluated using shear punch testing10.1016/j.jmrt.2014.04.004 ↗
22. Derivation of material properties using small punch and shear punch test methods10.1016/j.matdes.2022.110473 ↗
23. Hot shear deformation constitutive analysis and processing map of extruded Mg–12Li–1Zn bcc alloy10.1016/j.matdes.2013.07.060 ↗
24. Superplasticity of a hot rolled Mg–3Zn–0.5 RE–0.5 Zr (ZEK300) alloy10.1016/j.msea.2023.145403 ↗
25. Influence of high pressure torsion on microstructure evolution and mechanical properties of AZ80/SiC magnesium matrix composites10.1016/j.msea.2021.141916 ↗
26. Effect of Nb-C addition on the microstructure and mechanical properties of CoCrFeMnNi high entropy alloys during homogenisation10.1016/j.msea.2019.03.057 ↗
27. Effects of titanium addition on the microstructure and mechanical properties of quaternary CoCrFeNi high entropy alloy10.1016/j.msea.2022.143971 ↗
28. Microstructure and mechanical properties of spark plasma sintered AlCoFeMnNi high entropy alloy (HEA)-carbon nanotube (CNT) nanocomposite10.1016/j.jallcom.2020.158577 ↗
29. Shear punching of a Co20Cr20Fe20Ni20Mn15Cu5 high entropy alloy10.1016/j.jallcom.2021.161415 ↗
30. Effect of iron content on the microstructure evolution, mechanical properties and wear resistance of FeXCoCrNi high-entropy alloy system produced via MA-SPS10.1016/j.jallcom.2021.159410 ↗
31. Modeling the kinetics of deformation-induced martensitic transformation in AISI 316 metastable austenitic stainless steel10.1016/j.vacuum.2018.08.066 ↗
32. Abnormal grain growth in AISI 304L stainless steel10.1016/j.matchar.2014.08.022 ↗
33. Grain size dependent mechanical behavior and TRIP effect in a metastable austenitic stainless steel10.1016/j.ijplas.2022.103502 ↗
34. Finite element analysis of plastic deformation in shear punch test10.1016/j.matlet.2020.128953 ↗
35. Seventy years of Hall-Petch, ninety years of superplasticity and a generalized approach to the effect of grain size on flow stress10.1016/j.pmatsci.2023.101131 ↗
36. Explaining the drop of work-hardening rate and limitation of transformation-induced plasticity effect in metastable stainless steels during tensile deformation10.1016/j.scriptamat.2023.115465 ↗
37. Detailed Hall–petch analysis of cold rolled and annealed duplex 2205 stainless steel10.1002/srin.202100676 ↗
38. Zamani · 2022
39. Microstructural evolution after thermomechanical processing in an equiatomic, single-phase CoCrFeMnNi high-entropy alloy with special focus on twin boundaries10.1016/j.intermet.2014.05.014 ↗
40. Recrystallization and grain growth behavior of variously deformed CoCrFeMnNi high-entropy alloys: microstructure characterization and modeling10.1016/j.jmrt.2022.07.182 ↗
41. Significance of martensite reversion and austenite stability to the mechanical properties and transformation-induced plasticity effect of austenitic stainless steels10.1007/s11665-020-04798-7 ↗
42. Deformation mechanisms and enhanced mechanical properties of 304L stainless steel at liquid nitrogen temperature10.1016/j.msea.2020.140133 ↗
43. Hardening after annealing in nanostructured 316L stainless steel10.1016/j.nanoms.2019.12.003 ↗
44. Estimation of the kinetics of martensitic transformation in austenitic stainless steels by conventional and novel approaches10.1016/j.msea.2014.11.087 ↗
45. Elucidating the effects of cold rolling route on the mechanical properties of AISI 316L austenitic stainless steel10.1016/j.msea.2023.144616 ↗
46. Unraveling the effect of deformation temperature on the mechanical behavior and transformation-induced plasticity of the SUS304L stainless steel10.1002/srin.202000114 ↗
47. Metastability in high-entropy alloys: a review10.1557/jmr.2018.306 ↗
48. Evidence of FCC to HCP and BCC-martensitic transformations in a CoCrFeNiMn high-entropy alloy by severe plastic deformation10.1016/j.msea.2021.140875 ↗
49. Superplasticity of fine-grained austenitic stainless steels: a review
50. Microstructural evolutions during reversion annealing of cold-rolled AISI 316 austenitic stainless steel10.1007/s11661-018-4583-6 ↗
51. Effect of grain size on strength and strain rate sensitivity in the CrMnFeCoNi high-entropy alloy10.1016/j.jmrt.2022.07.181 ↗
52. Correlation of tensile test properties with those predicted by the shear punch test10.1016/j.matdes.2012.11.057 ↗
53. Correlation between shear punch and tensile strength for low-carbon steel and stainless steel sheets10.1007/s11665-012-0256-6 ↗
54. Mechanical response of a metastable austenitic stainless steel under different deformation modes10.1080/02670836.2020.1868104 ↗
55. Evolutions of mechanical properties of AISI 304L stainless steel under shear loading10.1016/j.msea.2020.139667 ↗
56. Work hardening under shear and tensile deformation modes10.1080/02670836.2022.2062650 ↗