journal article·2024-05Open access

Structural insights into T1 precipitation and age hardening by Zn alloying for T6 treated Al–Cu–Li based alloys with a high Cu/Li ratio

Hua Wang, Dengfeng Yin, Ming-Chun Zhao, Andrej Atrens

Abstract

T1 (Al2CuLi) nano-phase precipitation has been a major focus in developing new multi-microalloyed Al–Cu–Li alloys. Nevertheless, more understanding is required. This work investigated the effect of Zn alloying on the microstructure and mechanical properties of multi-element Al–Cu–Li alloys with a high Cu/Li ratio using a combination of advanced electron microscopy and first-principles calculations. Zn alloying (i) induced a higher density of geometrically-necessary dislocations after solid-solution treatment, which increased the T1 nucleation rate during the early aging stage; (ii) promoted T1 growth by substituting Al or Cu atoms in the T1 structure; and (iii) profoundly increased the aging kinetics, the age hardening response, and the strength. In addition, the co-segregation of Zn, Mg and Cu at the T1/Al interface helped to stabilize the fine T1 nano-platelets. These structural insights into T1 precipitation and age hardening by Zn alloying can help to guide the optimal design of high-performance Zn micro-alloyed multi-element Al–Cu–Li alloys.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Strengthening mechanisms, deformation behavior, and anisotropic mechanical properties of Al-Li alloys: a review10.1016/j.jare.2017.12.004 ↗
2. Recent developments in advanced aircraft aluminium alloys10.1016/j.matdes.2013.12.002 ↗
3. Precipitates and intermetallic phases in precipitation hardening Al-Cu-Mg-(Li) based alloys10.1179/174328005X14357 ↗
4. Heterogeneous nucleation of the T1 phase on dispersoids in Al-Cu-Li alloys. Metallurgical and materials transactions
5. Microstructural evolution during ageing of Al–Cu–Li–x alloys10.1016/j.actamat.2013.12.001 ↗
6. Polmear · 2012
7. Study on the microstructure and age hardening capability in Al-Cu-Li alloys with different Cu/Li ratio10.1515/ijmr-2021-8626 ↗
8. Aging kinetics of friction stir welded Al-Cu-Li-Mg-Ag and Al-Cu-Li-Mg alloys10.1016/j.matdes.2016.07.126 ↗
9. The effect of major constituents on microstructure and mechanical properties of cast Al-Li-Cu-Zr alloy10.1016/j.matchar.2020.110800 ↗
10. The influence of Cu/Li ratio on precipitation in Al–Cu–Li–x alloys10.1016/j.actamat.2012.12.041 ↗
11. Microstructure and mechanical properties of Mg, Ag and Zn multi-microalloyed Al–(3.2–3.8)Cu–(1.0–1.4)Li alloys10.1016/S1003-6326(15)63821-3 ↗
12. A novel GP-Li precursor and the correlated precipitation behaviors in Al-Cu-Li alloys with different Cu/Li ratio10.1016/j.actamat.2022.118442 ↗
13. First-principles insights into solute partition among various nano-phases in Al-Cu-Li-Mg alloys
14. Heterogeneous nucleation of the T1 phase on dispersoids in Al-Cu-Li alloys. Metallurgical and materials transactions
15. Mechanism of Al2CuLi (T1) nucleation and growth10.1007/BF02656798 ↗
16. The effect of plastic deformation on Al2CuLi (T1) precipitation10.1007/BF02656799 ↗
17. Quantification of the influence of increased pre-stretching on microstructure-strength relationships in the Al–Cu–Li alloy AA219510.1016/j.actamat.2016.02.017 ↗
18. Influence of pre-stretching at ambient and cryogenic temperatures on dislocation configuration, precipitation behaviour, and mechanical properties of 2195 Al-Cu-Li alloy10.1016/j.jmrt.2022.12.126 ↗
19. Effects of heat treatment and pre-stretching on the mechanical properties and microstructure evolution of extruded 2050 Al–Cu–Li alloy10.1016/j.msea.2022.143236 ↗
20. Achieving high strength and ductility of Al-Cu-Li alloy via creep aging treatment with different pre-strain levels
21. Effect of the aging process and pre-deformation on the precipitated phase and mechanical properties of 2195 Al–Li alloy10.1016/j.msea.2021.142394 ↗
22. Effects of a small addition of magnesium and silver on the precipitation of T1 phase in an Al-4%Cu-1.1%Li-0.2%Zr alloy10.1016/0921-5093(95)10157-8 ↗
23. Trace element effects on precipitation processes and mechanical properties in an Al-Cu-Li alloy. Metallurgical and materials transactions
24. A combinatorial approach for studying the effect of Mg concentration on precipitation in an Al–Cu–Li alloy10.1016/j.scriptamat.2015.07.042 ↗
25. Effect of Ag addition on the age hardening and precipitation behavior in an Al-Cu-Li-Mg-Zn-Mn-Zr alloy10.1016/j.matchar.2020.110184 ↗
26. A review of manufacturing processes, mechanical properties and precipitations for aluminum lithium alloys used in aeronautic applications10.1016/j.heliyon.2022.e12565 ↗
27. The effect of minor solute additions on the precipitation path of an Al Cu Li alloy10.1016/j.actamat.2016.05.050 ↗
28. Microscopy and microanalysis of complex nanosized strengthening precipitates in new generation commercial Al–Cu–Li alloys10.1111/jmi.12143 ↗
29. Microstructural characteristics and mechanical properties of extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn alloy10.1016/j.msea.2018.11.050 ↗
30. Microstructure characteristics of an ultra-high strength extruded Al-4.7Cu–1Li-0.5Mg-0.1Zr–1Zn alloy during heat treatment10.1016/j.jallcom.2019.152216 ↗
31. Microstructural evolution upon heat treatments and its effect on corrosion in Al-Zn-Mg alloys containing Sc and Zr10.1016/j.jmrt.2020.03.025 ↗
32. The hot deformation characteristics and the associated microstructural evolution of an Al–Cu–Li–Zn alloy studied by constitutive equations and processing maps10.1016/j.jmrt.2023.09.222 ↗
33. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set10.1103/PhysRevB.54.11169 ↗
34. From ultrasoft pseudopotentials to the projector augmented -wave method10.1103/PhysRevB.59.1758 ↗
35. Generalized gradient approximation made Simple [Phys. Rev. Lett. 77, 3865 (1996)]10.1103/PhysRevLett.78.1396 ↗
36. Formation of coherent, core-shelled nano-particles in dilute Al-Sc-Zr alloys from the first-principles10.1016/j.jmst.2018.11.004 ↗
37. Giant hardening response in AlMgZn(Cu) alloys10.1016/j.actamat.2020.116617 ↗
38. First-principles insights into complex interplays among nano-phases in an Al-Cu-Li-Zr alloy10.1016/j.actamat.2022.118304 ↗
39. Corrosion and antibacterial performance of novel selective-laser-melted (SLMed) Ti-xCu biomedical alloys10.1016/j.jallcom.2020.158415 ↗
40. Enhanced initial biodegradation resistance of the biomedical Mg-Cu alloy by surface nanomodification10.1016/j.jma.2021.12.013 ↗
41. Strengthening mechanisms in Al alloys - an overview of natural limits and engineering possibilities
42. Z-contrast stem for materials science10.1016/0304-3991(89)90173-3 ↗
43. Formation mechanism of precipitate T1 in AlCuLi alloys10.1016/j.jallcom.2014.10.208 ↗
44. Investigation on formation mechanism of T1 precipitate in an Al-Cu-Li alloy10.1016/j.jallcom.2017.06.198 ↗
45. Influence of Sc content on the microstructure and mechanical properties of cast Al-2Li-2Cu-0.5Mg-0.2Zr alloy10.1016/j.matchar.2018.05.046 ↗
46. First-principles calculations of bulk and interfacial Thermodynamic properties of the T1 phase in Al-Cu-Li alloys10.1016/j.scriptamat.2021.114009 ↗
47. Formation of the primary Second phases and their influence on the mechanical properties of an as-cast Al–Li–Mg alloy with multi-microalloying (Sc, Zr, Er and Ti)10.1007/s40962-023-01054-1 ↗
48. Evolution of microstructure and texture for an Al-0.4 Er alloy during accumulative roll bonding10.1016/j.jallcom.2019.152005 ↗
49. Strengthening mechanisms in a high-strength bulk nanostructured Cu–Zn–Al alloy processed via cryomilling and spark plasma sintering10.1016/j.actamat.2012.09.036 ↗
50. Strengthening of an Al–Cu–Sn alloy by deformation-resistant precipitate plates10.1016/j.actamat.2008.03.028 ↗
51. Influence of graphene oxide (GO) on microstructure and biodegradation of ZK30-xGO composites prepared by selective laser melting10.1016/j.jma.2019.10.004 ↗
52. Influence of stacking-fault energy on microstructural characteristics of ultrafine-grain copper and copper–zinc alloys10.1016/j.actamat.2007.10.053 ↗
53. The superposition of strengthening contributions in engineering alloys10.1016/j.msea.2013.06.032 ↗
54. Independent and combined roles of trace Mg and Ag additions in properties precipitation process and precipitation kinetics of Al–Cu–Li–(Mg)–(Ag)–Zr–Ti alloys10.1016/S1359-6454(98)00079-2 ↗
55. Role of Ag and Mg on precipitation of T1 phase in an Al-Cu-Li-Mg-Ag alloy10.1016/S1359-6462(00)00651-5 ↗
56. In Vitro corrosion resistance and antibacterial performance of novel Fe-xCu biomedical alloys prepared by selective laser melting10.1002/adem.202001000 ↗
57. Effect of grain refinement and crystallographic texture produced by friction stir processing on the biodegradation behavior of a Mg-Nd-Zn alloy10.1016/j.jmst.2018.11.025 ↗
58. Characterization of the precipitates in Al–Li(8090) alloy using thermal measurements and TEM examinations10.1016/S0921-4526(01)01470-3 ↗
59. 8 - aluminum-lithium alloys10.1016/B978-0-12-341831-9.50013-9 ↗
60. Classification of the role of microalloying elements in phase decomposition of Al based alloys10.1016/S1359-6454(99)00475-9 ↗
61. Nanostructure of aluminium alloy 2024: segregation, clustering and precipitation processes10.1016/j.actamat.2010.11.033 ↗
62. Quantification and modelling of the microstructure/strength relationship by tailoring the morphological parameters of the T1 phase in an Al–Cu–Li alloy10.1016/j.actamat.2014.04.046 ↗
63. Strengthening mechanisms of T1 precipitates and their influence on the plasticity of an Al–Cu–Li alloy10.1016/j.msea.2014.03.024 ↗
64. Size distribution and volume fraction of T1 phase precipitates from TEM images: direct measurements and related correction10.1016/j.micron.2015.06.002 ↗
65. Metallurgical factors affecting fracture toughness of aluminum alloys10.1007/BF02672285 ↗
66. Relationship between fracture toughness, fracutre path, and microstructure of 7050 aluminum alloy: Part II. Multiple micromechanisms-based fracture toughness model. Metallurgical and materials transactions
67. Effect of composition on tensile properties and fracture toughness of Al–Zn–Mg alloy (A7N01S-T5) used in high speed trains10.1016/j.matdes.2015.11.107 ↗