Effect of annealing and cold rolling on interface microstructure and properties of Ti/Al/Cu clad sheet fabricated by horizontal twin-roll casting
Source abstract
Abstract
In this study, a Ti/Al/Cu three-layer clad sheet was fabricated using horizontal twin-roll casting (HTRC) technology. The interfacial morphology, interfacial microstructure and phases, interfacial bonding strength, micro-hardness, and tensile properties of the clad sheet under different annealing and cold rolling conditions were investigated. The surface morphology of the titanium, copper and aluminum sheets after peeling was observed. Compared with the traditional compounding process, the cast-rolling bonding process can realize the direct combination of molten metal and solid metal strip and achieve higher bonding strength. In the as-cast sheet, the thickness of the diffusion layer is 3.6 μm and the average peel strength (APS) is 20.2 N/mm at the Ti/Al interface, meanwhile the values at the Cu/Al interface are 3.2 μm and 13.8 N/mm. Before the formation of intermetallic compound (IMC) at the interface, increasing annealing temperature can improve the bonding strength by promoting atomic interdiffusion. Further cold rolling can also improve the bonding strength by forming a wavelike interface. Under the action of huge rolling force, the matrices that were not well bonded in the cast-rolling process are contacted at the atomic scale, and as a result new bonding regions are created. By improving the interfacial bonding strength, appropriate annealing and cold rolling processes make the deformation of clad sheet more cooperative. According to the results obtained in this study, the best subsequent processing technology for Ti/Al/Cu clad sheet fabricated by HTRC is annealing at 300 °C for 1.5 h followed by a single pass cold rolling with 40% reduction.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Cold roll bonding of multi-layered bi-metal laminate composites10.1016/j.compscitech.2009.03.018 ↗
2. Role of layered structure in ductility improvement of layered Ti-Al metal composite10.1016/j.actamat.2018.05.005 ↗
3. Bi-continuous metal matrix composites10.1016/S0921-5093(00)01879-7 ↗
4. Microstructural and mechanical properties of Cu–Ti plates bonded through explosive welding process10.1016/j.jmatprotec.2005.02.264 ↗
5. Bond strength optimization of Ti/Cu/Ti clad composites produced by roll-bonding10.1016/j.matdes.2015.05.010 ↗
6. Interfacial microstructure and mechanical properties of Cu/Al clad sheet fabricated by asymmetrical roll bonding and annealing10.1016/j.msea.2011.09.087 ↗
7. Improvement of interfacial bonding strength in roll-bonded Mg/Al clad sheets through annealing and secondary rolling process10.1016/j.msea.2015.01.035 ↗
8. Effect of the steel sheet surface hardening state on interfacial bonding strength of embedded aluminum-steel composite sheet produced by cold roll bonding process10.1016/j.msea.2015.11.039 ↗
9. Microstructure and mechanical properties of Ti/Al explosive cladding10.1016/j.matdes.2013.12.012 ↗
10. Structural and mechanical properties of metallic–intermetallic laminate composites produced by explosive welding and annealing10.1016/j.matdes.2011.09.030 ↗
11. Microstructure and mechanical properties of CP-Ti/X65 bimetallic sheets fabricated by explosive welding and hot rolling10.1016/j.matdes.2015.08.021 ↗
12. Effect of thermal tempering on microstructure and mechanical properties of Mg-AZ31/Al-6061 diffusion bonding10.1016/j.msea.2016.04.011 ↗
13. Effect of heat treatment on bonding mechanism and mechanical properties of high strength Cu/Al/Cu clad composite10.1016/j.jallcom.2019.06.132 ↗
14. Effects of asymmetry and annealing on interfacial microstructure and mechanical properties of Cu/Al laminated composite fabricated by asymmetrical roll bonding10.1016/j.jallcom.2019.152453 ↗
15. Structural properties of Ti/Al clads manufactured by explosive welding and annealing10.1016/j.matdes.2015.11.087 ↗
16. Preparation, microstructure and mechanical properties of CP-Ti/AA6061-Al laminated composites by differential temperature rolling with induction heating10.1016/j.jmapro.2019.05.053 ↗
17. Cladding of Mg alloy with Al by twinroll casting10.1016/j.scriptamat.2011.01.013 ↗
18. A twin-roll caster to cast clad strip10.1016/S0924-0136(03)00100-6 ↗
19. Bonding process and interfacial reaction in horizontal twin-roll casting of steel/aluminum clad sheet10.1016/j.jmatprotec.2017.03.003 ↗
20. Twin-roll casting of aluminum-steel clad strips10.1016/j.jmapro.2013.08.008 ↗
21. Solid-liquid cast-rolling bonding (SLCRB) and annealing of Ti/Al cladding strip10.1016/j.matdes.2017.01.042 ↗
22. Effects of annealing temperature on the interfacial microstructure and bonding strength of Cu/Al clad sheets produced by twin-roll casting and rolling10.1016/j.jmatprotec.2020.116804 ↗
23. General relationship between strength and hardness10.1016/j.msea.2011.08.061 ↗
24. Investigation on bonding strength of steel/aluminum clad sheet processed by horizontal twin-roll casting, annealing and cold rolling10.1016/j.matdes.2016.09.061 ↗
25. Cold roll bondng strengths: review10.1179/026708310X12815992418256 ↗
26. Influence of diffusion mechanisms in aluminium solid-state welding processes10.1016/j.proeng.2014.10.300 ↗
27. An investigation into aluminum-aluminum bimetal fabrication by squeeze casting10.1016/j.matdes.2014.11.051 ↗
28. Interface strengthening of a roll-bonded two-ply Al/Cu sheet by short annealing10.1016/j.matchar.2021.111021 ↗
29. Cladding of aluminum on AISI 304L stainless steel by cold roll bonding: mechanism, microstructure, and mechanical properties10.1016/j.msea.2014.06.109 ↗