journal article·2023-03Open access

The impacts of M/A constituents decomposition and complex precipitation on mechanical properties of high-strength weathering steel subjected to tempering treatment

Liyang Zhao, Qiuming Wang, Genhao Shi, Bing Hu, Shibiao Wang, Mingliang Qiao, Qingfeng Wang, Riping Liu

Abstract

The impact of microstructure evolution on the mechanical properties of a typical 500 MPa-grade weathering steel produced by an identical thermo-mechanical control process and different tempering treatments at 450–650 °C were thoroughly investigated mainly using scanning electron microscopy (SEM) equip with an electron backscatter diffraction (EBSD), high-resolution transmission electron microscopy (HRTEM), and X-ray diffractometer (XRD). Results indicated that the as-rolled steel consists of granular bainitic ferrite (GBF) and a considerable amount of martensite/austenite (M/A) constituents, exhibiting unsatisfied mechanical properties. As the tempering temperature increased from 450 to 550 and 650 °C, the massive twin-type M/A constituents decomposed preferentially into carbides following the sequence of Fe3C→(Cr, Mn, Fe)3C→(Cr, Mn, Fe)3C + (Cr, Mn)23C6, with a small amount of fine lath-type M/A constituents remained. The matrix recovered with the bainitic ferrite laths merged, the dislocation density decreased and the proportion of high-angle grain boundary (HAGB) increased. Nanoscale (Ti, Nb)C and ε-Cu particles also precipitated simultaneously, leading to an increase of yield strength. The strain hardening capacity and hence the tensile strength reduced resulting from the decomposition of M/A constituents. Moreover, the impact toughness was first enhanced by tempering at 450–600 °C with the decreasing twin-type M/A constituents content and increasing HAGBs proportion, and then deteriorated by tempering at 650 °C due to the precipitation of necklace-like M23C6 carbides at the grain boundaries. An optimum mechanical property combination was achieved via tempering at 550–600 °C.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Effect of Si content on the microstructures and the impact properties in the coarse-grained heat-affected zone (CGHAZ) of typical weathering steel10.1016/j.msea.2019.138082 ↗
2. Microstructures and mechanical properties of a new multi-functional 460MPa grade construction structural steel10.1007/s40195-021-01359-2 ↗
3. Steels for bridge structures10.1007/s11015-020-00911-2 ↗
4. Effect of tempering temperature on carbide precipitation and mechanical properties of marine atmospheric corrosion resistant steel10.1007/s11665-021-06335-6 ↗
5. Controlling atmospheric corrosion of weathering steel using anodic polarization protection technique10.3390/pr9081469 ↗
6. Effect of microstructural constituents on strength–toughness combination in a low carbon bainitic steel10.1016/j.msea.2014.05.084 ↗
7. Correlation of microstructure feature with impact fracture behavior in a TMCP processed high strength low alloy construction steel
8. Experimental design of Cu content in weathering resistance steel for industrial atmosphere application10.1088/2053-1591/ab71c9 ↗
9. Effect of Si content on the corrosion behavior of 420 MPa weathering steel10.3390/met9050486 ↗
10. Mo content effect on microstructures and toughness of the simulated coarse-grained heat-affected zone of weathering bridge steels10.1007/s11665-022-06687-7 ↗
11. Microstructural characteristics and impact fracture behaviors of low-carbon vanadium-microalloyed steel with different nitrogen contents
12. Effect of welding heat input on microstructural evolution, precipitation behavior and resultant properties of the simulated CGHAZ in high-N V-alloyed steel10.1016/j.matchar.2020.110201 ↗
13. Zajac · 1995 · 11
14. Effect of TMCP rolling schedules on the microstructure and performance of X70 steel10.1016/j.matchar.2021.111207 ↗
15. Structure-mechanical property relationship in a high strength microalloyed steel with low yield ratio: the effect of tempering temperature10.1016/j.msea.2014.05.004 ↗
16. Effect of martensite–austenite constituents on impact toughness of pre-tempered MnNiMo bainitic steel10.1016/j.matchar.2020.110139 ↗
17. The tempering behavior of martensite/austenite islands on the mechanical properties of a low alloy Mn-Ni-Mo steel with granular bainite
18. Nano-sized precipitation and properties of a low carbon niobium micro-alloyed bainitic steel10.1016/j.msea.2015.05.101 ↗
19. Effect of tempering on the microstructure and properties of a new multi-functional 460 MPa Grade construction structural steel10.1016/j.jmrt.2022.03.037 ↗
20. The tempering behavior of granular structure in a Mn-series low carbon steel10.1016/j.msea.2010.10.097 ↗
21. Crystal structure evolution of the Cu-rich nano precipitates from bcc to 9R in reactor pressure vessel model steel10.1007/s40195-013-0170-4 ↗
22. Precipitation behavior during thin slab thermomechanical processing and isothermal aging of copper-bearing niobium-microalloyed high strength structural steels: the effect on mechanical properties10.1016/j.msea.2011.08.047 ↗
23. In-depth understanding of the relationship between dislocation substructure and tensile properties in a low-carbon microalloyed steel10.1016/j.msea.2022.143681 ↗
24. Effect of tempering temperature on microstructure and mechanical properties of nanostructured bainitic steel10.1016/j.msea.2021.142357 ↗
25. Effect of two-step tempering treatment on microstructure and impact toughness of bainitic steel for heavy wall thickness reactor pressure vessels10.1016/j.matchar.2019.110070 ↗
26. Microstructural evolution and mechanical property changes of a new nitrogen-alloyed Cr-Mo-V hot-working die steel during tempering
27. Characterization of the microstructures and mechanical properties of 25CrMo48V martensitic steel tempered at different times10.1016/j.msea.2012.08.049 ↗
28. Strain-induced precipitation in Ti microalloyed steel by two-stage controlled rolling process10.1016/j.jmrt.2020.11.040 ↗
29. Evolution of nano-size precipitation and mechanical properties in a high strength-ductility low alloy steel through intercritical treatment10.1016/j.msea.2017.08.061 ↗
30. Structure–mechanical property relationship in a low carbon Nb–Cu microalloyed steel processed through a three-step heat treatment: the effect of tempering process10.1016/j.msea.2014.09.079 ↗
31. Change of tensile behavior of a high-strength low-alloy steel with tempering temperature10.1016/j.msea.2009.03.085 ↗
32. The interaction between ε-copper and dislocation in a high copper 17-4PH steel10.1016/j.msea.2019.03.092 ↗
33. Nano-precipitates evolution and their effects on mechanical properties of 17-4 precipitation-hardening stainless steel10.1016/j.actamat.2018.06.031 ↗
34. Strengthening a fine-grained low activation martensitic steel by nanosized carbides10.1016/j.msea.2019.138471 ↗
35. An approach to define the effective lath size controlling yield strength of bainite10.1016/j.msea.2010.06.061 ↗
36. Effect of tempering temperature on resistance to deformation behavior for low carbon bainitic YP960 steels10.1016/j.msea.2014.09.054 ↗
37. Carbide precipitation in Nb-V-Ti microalloyed ultra-high strength steel during tempering10.1016/j.msea.2016.12.019 ↗
38. Improved strength-ductility-toughness balance of a precipitation-strengthened low-carbon medium-Mn steel by adopting intercritical annealing-tempering process10.1016/j.msea.2020.140636 ↗
39. Development of high strength hot rolled low carbon copper-bearing steel containing nanometer sized carbides10.1016/j.msea.2015.02.067 ↗
40. Improvement of mechanical properties for low carbon ultra-high strength steel strengthened by Cu-rich multistructured precipitation precipitation via modification to bainite
41. Effect of nanoscale Cu-riched clusters on strength and impact toughness in a tempered Cu-bearing HSLA steel10.1007/s40195-021-01277-3 ↗
42. Effects of welding and post-weld heat treatments on nanoscale precipitation and mechanical properties of an ultra-high strength steel hardened by NiAl and Cu nanoparticles10.1016/j.actamat.2016.08.066 ↗
43. Influence of Mn on microstructural evolution in Ti-killed C–Mn steel10.1016/S1359-6462(02)00437-2 ↗
44. Thermal stability of austenite retained in bainitic steels10.1016/j.msea.2009.11.063 ↗
45. The tempering of iron- carbon martensite; dilatometric and calorimetric analysis10.1007/BF02645469 ↗
46. Effect of tempering temperature on the microstructure and mechanical properties of a reactor pressure vessel steel10.1016/j.jnucmat.2016.05.017 ↗
47. Three-dimensional atom probe characterization of alloy element partitioning in cementite during tempering of alloy steel10.1016/j.ultramic.2007.02.033 ↗
48. Study on diversified carbide precipitation in high-strength low-alloy steel during tempering10.1002/srin.202000723 ↗
49. Precipitation behavior of Ti-Nb-V-Mo quaternary microalloyed high strength fire-resistant steel and its influence on mechanical properties10.1016/j.msea.2021.140865 ↗
50. Aging characteristics and strengthening behavior of a low-carbon medium-Mn Cu-bearing steel10.1016/j.msea.2018.05.097 ↗
51. Mechanical properties and precipitation behavior of high strength hot-rolled ferritic steel containing Nb and V10.1016/j.jmrt.2021.07.107 ↗
52. Investigation of local tensile strength and ductility properties of an X100 submerged arc seam weld10.1016/j.msea.2019.138475 ↗
53. The carbides, tensile properties, and work-hardening behavior of annealed H13 die steels with varied yttrium contents