Changes in microstructure and mechanical properties of 2219 Al alloy during hot extrusion and post-extrusion aging
Source abstract
Abstract
2219 Al alloy is widely used in the aerospace industry owing to its outstanding properties. In this study, we evaluated the effects of the extrusion temperature and extrusion ratio on the microstructure and mechanical properties of extruded 2219 Al alloy specimens, including the changes during post-extrusion aging. In the extrusion temperature range of 380–500 °C, the mechanical properties of the bar after extrusion at 470 °C were the best. Furthermore, extrusion ratios up to 25:1 produced extruded rods with excellent mechanical properties and microstructure. Increasing the extrusion temperature increased the dissolution of the eutectic θ phase in the solid solution and accelerated the breakage of the inclusions contained Mn/Fe. Some larger and coarse as-cast grains were mechanically fractured during hot extrusion, with the fragments then rotated towards directions with high Schmid factors, thus forming banded dynamic recrystallization regions. The grain boundaries of the recrystallized grains were predominantly low-angle boundaries. The 2219 Al alloy aged at 170 °C for 16 h produced the densest and most uniform distribution of needle-like nanoscale θ′ phase inside the grains, resulting in an average hardness of 149 HV. Further increasing the aging time and temperature resulted in the aggregation and growth of θ′ phase precipitates.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Corrosion resistance behaviour of graphene/polyvinyl alcohol nanocomposite coating for aluminium-2219 alloy10.1016/j.jallcom.2017.04.324 ↗
2. Effect of ultrasonic impact treatment on microstructure and corrosion behavior of friction stir welding joints of 2219 aluminum alloy10.1016/j.jmrt.2022.03.068 ↗
3. Formability of AA 2219-O sheet under quasi-static, electromagnetic dynamic, and mechanical dynamic tensile loadings10.1016/j.jmst.2020.07.023 ↗
4. The quasi-static deformation and final fracture behavior of aluminum alloy 221910.1016/j.msea.2008.07.033 ↗
5. Analysis and homogenization of residual stress in aerospace ring rolling process of 2219 aluminum alloy using thermal stress relief method10.1016/j.ijmecsci.2019.04.040 ↗
6. Modified kinetic model for describing continuous dynamic recrystallization behavior of Al 2219 alloy during hot deformation process10.1016/j.jallcom.2019.153301 ↗
7. Hot deformation induced microstructural evolution in local-heterogeneous wire + arc additive manufactured 2219 Al alloy10.1016/j.jallcom.2021.158949 ↗
8. A modified Arrhenius constitutive model of 2219-O aluminum alloy based on hot compression with simulation verification10.1016/j.jmrt.2022.06.080 ↗
9. Research on process optimization and rapid prediction method of thermal vibration stress relief for 2219 aluminum alloy rings10.1515/rams-2022-0028 ↗
10. Influence of pre-deformation and subsequent ageing on the hardening behavior and microstructure of 2219 aluminum alloy forgings10.1016/j.jallcom.2016.06.111 ↗
11. Effects of warm saddle forging deformation on the reduction of second-phase particles and control of the three-dimensional mechanical properties of 2219 aluminum alloy rings10.1016/j.msea.2021.140737 ↗
12. Refinement of second-phase particles and grain structures of 2219 Al-Cu alloy forgings using an improved thermomechanical treatment process10.1016/j.matchar.2021.110927 ↗
13. Processing map of 2219 Al alloy prepared by internal electromagnetic stirring direct chill casting10.1016/j.jmrt.2022.03.177 ↗
14. Grain refinement in aluminum alloy 2219 during ECAP at 250 °C10.1016/j.msea.2007.04.112 ↗
15. Second phase particles and mechanical properties of 2219 aluminum alloys processed by an improved ring manufacturing process10.1016/j.msea.2020.139226 ↗
16. Microstructure evolution and mechanical properties of 2219 Al alloy during aging treatment10.1007/s11665-017-2621-y ↗
17. Effects of cryogenic deformation on second-phase Al2Cu particles and mechanical properties of 2219 Al-Cu alloy rings10.1007/s12540-019-00468-z ↗
18. Microstructure-based modeling of the PMZ mechanical properties in 2219-T8 aluminum alloy TIG welding joint10.1016/j.matdes.2022.111133 ↗
19. Long-term thermal ageing of the 2219-T851 and the 2050-T84 Al-Cu alloys
20. Effect of pre-deformation on microstructure and mechanical properties of 2219 aluminum alloy sheet by thermomechanical treatment10.1016/S1003-6326(12)61733-6 ↗
21. Investigation of quench sensitivity of high strength 2219 aluminum alloy by TTP and TTT diagrams10.1016/j.jallcom.2016.08.160 ↗
22. Effects of pre-deformation on the microstructures and corrosion behavior of 2219 aluminum alloys10.1016/j.msea.2018.03.041 ↗
23. Microstructural characteristics and mechanical properties of friction stir welded thick 5083 aluminum alloy10.1007/s11661-016-3819-6 ↗
24. Partial penetration laser-based welding of aluminum alloy (AA 5083-H32)10.1016/j.ijleo.2016.05.007 ↗
25. Controlling the textures of the Al alloy sheet via dissimilar channel angular pressing10.1016/j.msea.2004.11.058 ↗
26. Effect of the Mg contents on the annealing mechanism and shear texture of Al–Mg alloys10.1016/j.msea.2020.139471 ↗
27. Experimental analysis of deformation texture evolutions in pure Cu, Cu-37Zn, Al-6Mg, and - 8Mg alloys at cold-rolling processes10.1016/j.jallcom.2022.167879 ↗