journal article·2023-05Open access

Texture evolution and its influence mechanism on properties of single crystal copper and polycrystalline copper during cumulative deformation

Xin Li, Yanjun Zhou, Yahui Liu, Shaolin Li, Kexing Song, Cunli Feng, Baoan Wu, Pengfei Zhang, Hanjiang Wu, Jihua Gu, Siyu He, Yan Gao

Abstract

The φ16 mm single crystal copper rod was prepared by heated-mold horizontal continuous casting, and the φ16 mm polycrystalline copper rod was prepared by up-casting technology. Both of them were drawn to φ0.2 mm, the conductivity, strength, elongation, and microstructure evolution of single-crystal copper wire and polycrystal copper wire were compared and analyzed. The results show that the plasticity of as-cast single-crystal copper rod is 13.94% higher than that of as-cast polycrystalline copper rod. When drawing to φ0.2 mm, a single crystal copper wire with high strength (506 MPa) and high conductivity (98.01% IACS). At the same deformation amount, the single crystal copper wire obviously deforms more slowly and has a higher plastic deformation capacity; the texture transformation of single crystal copper wire is from soft → hard orientation, selective orientation to discrete distribution, while the weave transformation of polycrystalline copper wire is from soft → hard orientation, then from hard → soft orientation, and finally stabilizes to selective orientation. The microstructural evolution of single-crystal copper wire and polycrystalline copper wire during continuous deformation was observed: dislocation entanglement into dislocation cells by slip → microstrip structure → lamellar organization → twinning organization, single-crystal copper wire appears twinning later, single-crystal copper deformation coordination ability is better than polycrystalline copper. It is found that the increase of dislocation density, the decrease of grain width and the increase of <111> texture are the main factors for the strength improvement of micro-nano pure copper wires.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Mechanisms for high strength and ultra-high electrical conductivity of Cu-3.5wt.%Ag alloy prepared by thermomechanical treatment
2. Nanostructured Al and Cu alloys with superior strength and electrical conductivity10.1007/s10853-015-9354-9 ↗
3. A nanostructural design to produce high-strength Al alloys with enhanced electrical conductivity10.1016/j.scriptamat.2013.12.002 ↗
4. Enhanced cyclic deformation responses of ultrafine-grained Cu and nanocrystalline Cu-Al alloys10.1016/j.actamat.2014.04.053 ↗
5. Effects of stacking fault energy and solute atoms on microstructural evolution of Cu, Ag, and Cu–Al alloys processed by equal channel angular pressing10.1016/j.msea.2020.140716 ↗
6. Texture evolution in equal-channel angular extrusion10.1016/j.pmatsci.2009.01.001 ↗
7. Microstructure evolution and strengthening mechanisms of cold-drawn commercially pure aluminum wire10.1016/j.msea.2015.04.102 ↗
8. Improvement of the strength of magnesium alloy processed by equal channel angular extrusion10.1016/j.scriptamat.2008.07.007 ↗
9. Effect of transverse grain boundary on microstructure, texture andMechanical properties of drawn copper wires10.1016/j.jmst.2013.04.018 ↗
10. Dependence of texture evolution on initial orientation in drawn single crystal copper10.1016/j.matchar.2010.12.006 ↗
11. Size effects in tensile testing of thin cold rolled and annealed Cu foils10.1016/j.msea.2005.10.060 ↗
12. Effect of cold drawing strain on the microstructure, mechanical properties and electrical conductivity of low-oxygen copper wires10.1016/j.msea.2021.141348 ↗
13. On the contribution of boundaries towards strength in oxygen-free high conductivity copper subjected to repetitive upsetting – extrusion10.1016/j.pnsc.2016.11.011 ↗
14. Continuous casting of single crystal ingots by the O.C.C. Process10.1007/BF03257948 ↗
15. Microstructure evolution of high-strength and ultra-high-conductivity microfilament wire prepared by continuous deformation of single crystal copper10.1007/s10853-022-07919-w ↗
16. Enhanced electrical conductivity and mechanical properties in thermally stable fine-grained copper wire10.1038/s43246-021-00150-1 ↗
17. Microstructure and mechanical properties of a Cu-Fe-Nb alloy with a high product of the strength times the elongation
18. Microscopic mechanisms contributing to the synchronous improvement of strength and plasticity (SISP) for TWIP copper alloys
19. Enhancing performance of the CuCrZrTiV alloys through increasing recrystallization resistance and two-step thermomechanical treatments10.1016/j.jnucmat.2020.152482 ↗
20. Annealing behavior of gradient structured copper and its effect on mechanical properties10.1016/j.msea.2017.07.023 ↗
21. Strengthening mechanism of ultra-high strength Cu–20Ag alloy wire induced by cumulative strain10.1016/j.msea.2022.143957 ↗
22. Ductility sensitivity to stacking fault energy and grain size in Cu-Al alloys10.1080/21663831.2015.1136969 ↗
23. Correlation mechanism of grain orientation/microstructure and mechanical properties of Cu–Ni–Si–Co alloy10.1016/j.msea.2021.141239 ↗
24. Influence of precipitates on the microstructure and texture during the rolling of Al-Cu and Al-Mn single crystals with rolling texture orientations
25. EBSD analysis of grain-refinement mechanisms operating during equal-channel angular pressing of commercial-purity titanium10.1016/j.actamat.2019.05.014 ↗
26. Microstructure and texture gradient in copper deformed by equal channel angular pressing10.1016/j.actamat.2006.11.005 ↗
27. Effects of initial texture on deformation behavior during cold rolling and static recrystallization during subsequent annealing of AZ31 alloy10.1016/j.jmst.2020.04.074 ↗
28. Three principles for preparing Al wire with high strength and high electrical conductivity10.1016/j.jmst.2018.11.013 ↗
29. Effect of stacking fault energy on mechanical properties and strengthening mechanisms of brasses processed by cry rolling10.1016/j.matchar.2015.10.006 ↗
30. Book review: mechanical behavior of materials by M.A. Meyers and K.K. Chawla
31. Six decades of the Hall–Petch effect – a survey of grain-size strengthening studies on pure metals10.1080/09506608.2016.1191808 ↗
32. Effects of grain boundaries on cyclic deformation behavior of copper bicrystals and columnar crystals10.1016/S1359-6454(98)00162-1 ↗
33. Study on texture evolution and deformation mechanism of the Cu-Ni-Si alloy during cold-rolling treatment10.1016/j.proeng.2017.10.1068 ↗