journal article·2023-09Open access

Numerical simulation and experimental investigation of the laser cladding processes of Ti6Al4V with coaxial shroud protection

Peijie Lyu, Peifeng Li, Kaiyong Jiang

Abstract

Laser cladding with coaxial shroud protection offers the possibility to process reactive metals in an open environment. The numerical analysis was performed on the thermal field and dynamics of molten pool with the aim of clarifying the mechanism of the complex effects of the applied extra shielding gas on the resultant microstructure and surface quality of cladding layers of Ti6Al4V. A three-dimensional (3D) computational fluid dynamics (CFD) model was first developed to investigate the extra shielding gas effect on the molten pool. The simulation shows that the extra shielding gas influences both the surface and internal flow field characteristics of the molten pool. The predicted solidification parameters imply fully columnar microstructure in the entire cladding layer. Comparative analysis was then carried out between the numerical simulation and experiments. The electron backscattering diffraction (EBSD) examination reveals that the high cooling rate due to the extra shielding gas inhibits the formation of grain boundary α phase and simultaneously refines the microstructure. The extra shielding gas reduces the surface roughness of cladding layers, and its bunching effect improves the powder utilization. The multi-track cladding experiments reveal that the extra shielding gas can effectively suppress crack formation with a large overlap ratio. This study provides a better understanding of the effect of extra shielding gas flow on molten pool, which helps control and improve the quality of cladding layers.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. Toyserkani · 2004
2. An overview of Direct Laser Deposition for additive manufacturing; Part I: transport phenomena, modeling and diagnostics
3. Remanufacturing: trends and issues10.1007/s40684-017-0015-0 ↗
4. Coaxial laser metal wire deposition of Ti6Al4V alloy: process, microstructure and mechanical properties10.1016/j.jmrt.2022.08.068 ↗
5. Solute transport and composition profile during direct metal deposition with coaxial powder injection10.1016/j.apsusc.2011.09.023 ↗
6. Manipulating molten pool dynamics during metal 3D printing by ultrasound10.1063/5.0082461 ↗
7. Examination of molten pool with Marangoni flow and evaporation effect by simulation and experiment in selective laser melting
8. Numerical investigation on heat transfer of melt pool and clad generation in directed energy deposition of stainless steel
9. Numerical simulation and experimental study of cladding Fe60 on an ASTM 1045 substrate by laser cladding10.1016/j.surfcoat.2018.10.099 ↗
10. Hardness, grainsize and porosity formation prediction on the Laser Metal Deposition of AISI 304 stainless steel10.1016/j.ijmachtools.2018.08.004 ↗
11. Laser cladding assisted with an induction heater (LCAIH) of Ni–60%WC coating10.1016/j.jmatprotec.2015.02.026 ↗
12. Modeling of transport phenomena during the coaxial laser direct deposition process10.1063/1.3474655 ↗
13. Evolution of molten pool morphology and prediction of inclined cladding layer morphology10.1016/j.optlastec.2021.107164 ↗
14. Numerical simulation of multiphase transient field during plasma deposition manufacturing10.1063/1.2399341 ↗
15. Poprawe · 2011
16. Numerical simulation and experimental investigation of the effect of three-layer annular coaxial shroud on gas-powder flow in laser cladding10.1016/j.jmapro.2022.10.019 ↗
17. Modeling and simulation of 3D geometry prediction and dynamic solidification behavior of Fe-based coatings by laser cladding10.1016/j.optlastec.2021.107009 ↗
18. The relationship between convection mechanism and solidification structure of the iron-based molten pool in metal laser direct deposition10.1016/j.ijmecsci.2019.105207 ↗
19. Modeling of the effect of powder parameters on laser cladding using coaxial nozzle10.1016/j.surfcoat.2018.12.002 ↗
20. In situ tailoring microstructure in additively manufactured Ti-6Al-4V for superior mechanical performance10.1016/j.actamat.2016.12.027 ↗
21. Identifying defects and problems in laser cladding and suggestions of some remedies for the same10.1016/j.matpr.2018.02.297 ↗
22. Bakir · 2015
23. Investigation of cracking causes during multi-pass laser cladding of heat-resistant single crystal nickel alloy10.1016/j.procir.2020.09.059 ↗
24. Alhendal · 2012
25. Numerical and experimental study of laser aided additive manufacturing for melt-pool profile and grain orientation analysis10.1016/j.matdes.2017.10.033 ↗
26. Numerical simulation and experimental investigation of the influence of process parameters on gas-powder flow in laser metal deposition
27. In situ measurements and thermo-mechanical simulation of Ti–6Al–4V laser solid forming processes10.1016/j.ijmecsci.2019.01.043 ↗
28. Chapter 3 - convection boundary losses during laser cladding
29. Modeling forced convection in the thermal simulation of laser cladding processes10.1007/s00170-015-6831-x ↗
30. A FEM model for simulating temperature field in coaxial laser cladding of TI6AL4V alloy using an inverse modeling approach10.1016/j.ijheatmasstransfer.2013.04.050 ↗
31. A continuum method for modeling surface tension10.1016/0021-9991(92)90240-Y ↗
32. Saldi · 2012
33. Abramovich · 2003
34. Development of powder flow model of laser solid forming by analysis method10.1007/s00170-015-7481-8 ↗
35. The influence of the powder stream on high-deposition-rate laser metal deposition with inconel 71810.3390/met7100443 ↗
36. Mitigating oxygen pick-up during laser powder bed fusion of Ti-6Al-4V by limiting heat accumulation10.1016/j.matlet.2021.129365 ↗
37. Melt pool evolution on inclined NV E690 steel plates during laser direct metal deposition10.1016/j.optlastec.2020.106745 ↗
38. In-situ full-field mapping of melt flow dynamics in laser metal additive manufacturing
39. In-situ NbC reinforced Fe-based coating by laser cladding: simulation and experiment10.1016/j.surfcoat.2021.127027 ↗
40. Investigation on composition distribution of dissimilar laser cladding process using a three-phase model10.1016/j.ijheatmasstransfer.2021.120975 ↗
41. Numerical simulation of thermal field and Fe-based coating doped Ti10.1016/j.ijheatmasstransfer.2015.08.082 ↗
42. Thermo-mechanical model development and validation of directed energy deposition additive manufacturing of Ti–6Al–4V
43. Solidification
44. Molten pool characteristics of a nickel-titanium shape memory alloy for directed energy deposition10.1016/j.optlastec.2021.107215 ↗
45. Molten pool behavior and effect of fluid flow on solidification conditions in selective electron beam melting (SEBM) of a biomedical Co-Cr-Mo alloy
46. In-situ grain structure control in directed energy deposition of Ti6Al4V
47. Columnar to equiaxed transition during alloy solidification10.1360/02ye0337 ↗
48. Effect of β grain growth on variant selection and texture memory effect during α→ β→ α phase transformation in Ti–6 Al–4 V10.1016/j.actamat.2011.10.038 ↗
49. Lütjering · 2007
50. Crystallographic variant selection in Ti–6Al–4V10.1016/j.actamat.2004.07.034 ↗
51. Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400° C using in-situ EBSD10.1016/j.msea.2021.141761 ↗
52. A unified growth model of the secondary grain boundary α phase in TA15 Ti-alloy10.1016/j.jallcom.2016.08.013 ↗
53. 3D printing of high-strength aluminium alloys10.1038/nature23894 ↗
54. Powder particle attachment mechanisms onto liquid material10.1016/j.procir.2018.08.064 ↗
55. Analysis of coaxial laser cladding processing conditions10.1016/j.surfcoat.2004.06.029 ↗
56. Investigation on synergism between additive and subtractive manufacturing for curved thin-walled structure10.1080/17452759.2022.2029009 ↗
57. Simplification and experimental investigation of geometrical surface smoothness model for multi-track laser cladding processes10.1016/j.jmapro.2018.11.004 ↗
58. Effect of overlap rate on recrystallization behaviors of Laser Solid Formed Inconel 718 superalloy10.1016/j.optlastec.2012.06.043 ↗
59. Laser rapid manufacturing on vertical surfaces: analytical and experimental studies10.1016/j.surfcoat.2013.02.044 ↗
60. Role of porosity defects in metal 3D printing: formation mechanisms, impacts on properties and mitigation strategies10.1016/j.mattod.2022.08.014 ↗
61. The influence of stellite 6 particle size on the inter-track porosity in multi-track cladding10.1016/j.surfcoat.2006.01.008 ↗
62. Enhanced beads overlapping model for wire and arc additive manufacturing of multi-layer multi-bead metallic parts10.1016/j.jmatprotec.2017.10.017 ↗