journal article·2023-09Open access

Anodic electrochemical behaviors of Inconel 718 and Rene 65 alloys in NaNO3 solution

Shuanglu Duan, Jia Liu, Jingtao Wang, Bo Tang, Di Zhu

Abstract

Studying the behavior of anode materials during their electrochemical dissolution is the premise for and key to their electrochemical machining (ECM). In this study, electrochemical tests and ECM experiments on the Inconel 718 (IN718) and Rene 65 (R65) alloys in a 20 wt% NaNO3 solution were conducted to investigate their behaviors during anodic electrochemical dissolution. The passivation-related behaviors and structures of the interface of the two materials were measured based on the curves of potentiodynamic polarization and EIS. Information on the growth and composition of the passive film was obtained by potentiostatic polarization and XPS. The results showed that compared with IN718, the structure of the passive film on the surface of R65 was loose and unstable such that it had a weak resistance to corrosion. ECM tests were performed under different current densities, and the morphology of dissolution was identified. The grain boundaries of IN718 were completely exposed in the dissolved surface, and it had a lower surface roughness than R65. For R65, a high current density was conducive to the removal of blocky protrusions and lath structures. Finally, a model of dissolution is proposed to characterize the behaviors of IN718 and R65 during electrochemical dissolution.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced Machining and Optimization Techniques · Hydrogen embrittlement and corrosion behaviors in metals · Anodic Oxide Films and Nanostructures

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. State-of-the-art in surface integrity in machining of nickel-based super alloys10.1016/j.ijmachtools.2015.10.001 ↗
2. A review of developments towards dry and high speed machining of Inconel 718 alloy10.1016/S0890-6955(03)00159-7 ↗
3. Machinability of nickel based superalloys: a review10.1016/j.matpr.2017.02.266 ↗
4. Yield strength prediction in Ni-base alloy 718Plus based on thermo-kinetic precipitation simulation10.1016/j.msea.2014.04.054 ↗
5. AD730TM-A new nickel-based superalloy for high temperature engine rotative parts10.7449/2012/Superalloys_2012_911_919 ↗
6. Segregation and homogenization for a new nickel-based superalloy10.1016/j.vacuum.2020.109379 ↗
7. Hot deformation characteristics and dynamic recrystallization mechanisms of a novel nickel-based superalloy10.1002/adem.202000622 ↗
8. Investigation of high performance disc alloy GH4065 and associated advanced processing techniques
9. The machinability of nickel-based alloys: a review10.1016/S0924-0136(98)00314-8 ↗
10. New developments in electro-chemical machining10.1016/S0007-8506(07)63235-1 ↗
11. Electrochemical machining of complex components of aero-engines: developments, trends, and technological advances10.1016/j.cja.2019.09.016 ↗
12. Experimental research on the electrochemical machining of modern titanium-and nickel-based alloys for aero engine components10.1016/j.procir.2013.03.040 ↗
13. Electrochemical dissolution of cast iron in NaNO3 electrolyte10.1007/s10800-015-0809-0 ↗
14. Electrochemical dissolution behavior of titanium and titanium-based alloys in different electrolytes10.1016/j.procir.2016.02.208 ↗
15. Investigation of the electrochemical dissolution behavior of Inconel 718 and 304 stainless steel at low current density in NaNO3 solution10.1016/j.electacta.2014.12.155 ↗
16. Corrosion evaluation of superalloys Haynes 282 and Inconel 718 in hydrochloric acid10.1016/j.jallcom.2019.06.196 ↗
17. Anodic dissolution characteristics of Inconel 718 in C6H5K3O7 and NaNO3 solutions by pulse electrochemical machining10.1016/j.corsci.2021.109335 ↗
18. Electrochemical dissolution behavior of the nickel-based cast superalloy K423A in NaNO3 solution10.1016/j.electacta.2017.09.046 ↗
19. Electrochemical behavior of Inconel 718 fabricated by laser solid forming on different sections10.1016/j.corsci.2017.12.021 ↗
20. Wire electrochemical trimming the recast layer on René 88DT for aero-engine applications10.1016/j.electacta.2022.140372 ↗
21. Study on freckle of a high-alloyed GH4065 nickel base wrought superalloy
22. Microstructural evolution and corrosion behaviors of Inconel 718 alloy produced by selective laser melting following different heat treatments
23. Effect of stress-relief annealing on anodic dissolution behaviour of additive manufactured Ti-6Al-4V via laser solid forming10.1016/j.corsci.2019.04.002 ↗
24. Corrosion behavior and characteristics of passive films of laser powder bed fusion produced Ti–6Al–4V in dynamic Hank’s solution10.1016/j.matdes.2021.109907 ↗
25. Anodic characteristics and electrochemical machining of two typical γ-TiAl alloys and its quantitative dissolution model in NaNO3 solution10.1016/j.electacta.2019.135429 ↗
26. Corrosion behavior of a selective laser melted Inconel 718 alloy in a 3.5 wt.% NaCl solution10.1007/s11665-021-05909-8 ↗
27. Microstructure and electrochemical anodic behavior of Inconel 718 fabricated by high-power laser solid forming10.1016/j.electacta.2018.04.186 ↗
28. Electrochemical dissolution behaviour of Ti90Al6V4 and Ti60Al40 used for ECM applications10.1007/s10008-014-2621-x ↗
29. The mechanism of anodic dissolution of cobalt in neutral and alkaline electrolyte at high current density10.1016/j.electacta.2013.06.093 ↗
30. Corrosion behaviors of selective laser melted inconel 718 alloy in NaOH solution
31. The electrochemical dissolution characteristics of Inconel 718 nickel base super alloy in the condition of electrochemical machining10.20964/2018.01.75 ↗
32. Improved corrosion behaviour of electron beam melted Ti-6Al–4V alloy in phosphate buffered saline10.1016/j.corsci.2017.05.003 ↗
33. Study of the influence of the preparation method on the electrochemical dissolution behavior of Inconel 71810.1007/s10800-022-01693-y ↗
34. The history of the point defect model for the passive state: a brief review of film growth aspects10.1016/j.electacta.2010.11.005 ↗
35. Influence of surface modifications on pitting corrosion behavior of nickel-base alloy 718. Part 1: effect of machine hammer peening10.1016/j.corsci.2013.08.007 ↗
36. Characterisation of titanium oxide films by potentiodynamic polarisation and electrochemical impedance spectroscopy10.1179/147842208X373191 ↗
37. Corrosion evaluation of Ti–48Al–2Cr–2Nb (at.%) in Ringer's solution10.1016/j.actbio.2006.05.012 ↗
38. Microstructure and corrosion behavior of FeCrNiCoMnx (x= 1.0, 0.6, 0.3, 0) high entropy alloys in 0.5 M H2SO410.1016/j.corsci.2021.109694 ↗
39. The influence of phosphate on repassivation of 304 stainless steel in neutral chloride solution10.1016/S0013-4686(97)00224-7 ↗
40. Corrosion behavior of wire arc additive manufactured Inconel 718 superalloy10.1016/j.jallcom.2020.154455 ↗
41. Dependency of the pulsed electrochemical machining characteristics of Inconel 718 in NaNO3 solution on the pulse current
42. X-ray photoelectron spectroscopy study of the passive films formed on thermally sprayed and wrought Inconel 62510.1016/j.apsusc.2010.07.066 ↗
43. Corrosion and mechanical behavior of ion implanted bearing steels for improved fretting behavior10.1016/0257-8972(94)90047-7 ↗
44. Investigation of electrochemical dissolution behavior of Ni (γ)/Ni3Al (γ’) and Co (γ)/Co3Al (γ’) superalloys in NaNO3 solution10.1016/j.corsci.2022.110622 ↗
45. A study of precision current efficiency curve measurement with a casing-type anode10.3390/app11041425 ↗
46. Surface morphology analysis of 1Cr11Ni2W2MoV steel subjected to electrochemical machining in NaNO3 solution10.1149/1945-7111/ab798b ↗