journal article·2024-01Open access

Design of a 2.7 GPa ultra-high-strength high Co–Ni secondary hardening steel by two-step nano-size precipitation tailoring

Xiaoqi Liu, Chenchong Wang, Yufeng Zhang, Lingyu Wang, Wei Xu

Abstract

High-Co–Ni secondary hardening steels are valuable in the field of aviation materials. With the increasing demand of lightweight, further enhancing its strength has received widespread attention. In this study, instead of using only M2C carbides as the reinforcements in the traditional high Co–Ni secondary hardening steels, nano-size NiAl phases were introduced to provide additional strength. To obtain the collaborative precipitation of these two reinforcements, systematically thermodynamic calculation, including the driving force, coarsening rate, etc., was made to quantitatively tailor the composition and the two-step aging parameters. The calculation results showed that adding 1 % Al into the standard composition of M54 is a plan with high potential and a second aging process at 450 °C should be added to promote NiAl precipitation. Based on the experimental validation, the target microstructure formed as the design. With the dual-phase strengthening of NiAl particles and M2C carbides, the yield and tensile strength are greater than 2.3 and 2.7 GPa, respectively, which increases the strength of M54 steel by >30 %, retaining sufficient elongation and relatively low cost. This new designed alloy increased the strength–ductility balance of the high Co–Ni secondary hardening steels and aviation maraging steels from ∼12.5 to 13.5 GPa%.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Hardening mechanisms and impact toughening of a high-strength steel containing low Ni and Cu additions10.1016/j.actamat.2019.04.041 ↗
2. Controlling the MC and M2C carbide precipitation in Ferrium® M54® steel to achieve optimum ultimate tensile strength/fracture toughness balance10.1016/j.matchar.2018.03.041 ↗
3. Microstructural basis for the effect of chromium on the strength and toughness of AF1410-based high performance steels10.1007/BF02652345 ↗
4. Recovery and recrystallization of high purity lead determined with a low temperature calorimeter10.1016/0956-716X(91)90259-4 ↗
5. Genomic materials design: the ferrous frontier10.1016/j.actamat.2012.10.045 ↗
6. Liu · 2020
7. 2.47 GPa grade ultra-strong 15Co-12Ni secondary hardening steel with superior ductility and fracture toughness10.1016/j.jmst.2020.06.014 ↗
8. Xu · 2008
9. Ultrastrong steel via minimal lattice misfit and high-density nanoprecipitation10.1038/nature22032 ↗
10. Designing ultrastrong maraging stainless steels with improved uniform plastic strain via controlled precipitation of coherent nanoparticles10.1016/j.jmst.2021.04.011 ↗
11. Enhanced strength-ductility synergy in a new 2.2 GPa grade ultra-high strength stainless steel with balanced fracture toughness: elucidating the role of duplex aging treatment10.1016/j.jallcom.2022.167135 ↗
12. Olson · 2013
13. Refinement of Cu-M2C precipitates and improvement of strength and toughness by Ti microalloying in a Cu-bearing steel10.1016/j.msea.2020.140678 ↗
14. Prediction of the yield strength of a secondary-hardening steel10.1016/j.actamat.2013.04.052 ↗
15. Transmission electron microscopy examination of hardening and toughening phenomena in AerMet 10010.1007/BF02666329 ↗
16. Ultrafine-grained dual-phase maraging steel with high strength and excellent cryogenic toughness10.1016/j.actamat.2021.116878 ↗
17. Precipitate evolution and strengthening behavior during aging process in a 2.5 GPa grade maraging steel10.1016/j.actamat.2019.08.042 ↗
18. Investigation of precipitation in a new maraging stainless steel10.1016/0169-4332(95)00394-0 ↗
19. Handerhan · 1989 · 20A · 105
20. On the characteristics of M2C carbides in the peak hardening regime of AerMet 100 steel10.1007/s11661-998-0280-1 ↗
21. Austenite and precipitation in secondary-hardening ultra-high-strength stainless steel
22. Flower · 1995
23. 4340 steel with superior strength and toughness achieved by heterostructure via intercritical quenching and tempering10.3390/met13061139 ↗
24. Zhou · 2019
25. Govindaraj · 2021
26. A novel ultra-high strength maraging steel with balanced ductility and creep resistance achieved by nanoscale β-NiAl and Laves phase precipitates10.1016/j.actamat.2018.02.044 ↗
27. A sustainable ultra-high strength Fe18Mn3Ti maraging steel through controlled solute segregation and α-Mn nanoprecipitation10.1038/s41467-022-30019-x ↗
28. Development of Ni-free Mn-stabilised maraging steels using Fe2SiTi precipitates10.1016/j.actamat.2019.05.034 ↗
29. On the origin of planar slip in f.c.c. alloys10.1016/0001-6160(89)90143-0 ↗
30. Carbide precipitation and element distribution in high Co–Ni secondary hardening steel10.1007/s42243-018-0041-3 ↗
31. Microstructure analysis and yield strength simulation in high Co-Ni secondary hardening steel10.1016/j.msea.2016.05.069 ↗
32. Mechanical properties and nanoparticles precipitation behavior of multi-component ultrahigh strength steel10.1016/j.matdes.2020.108637 ↗
33. Stress–strain behavior of ferrite and bainite with nano-precipitation in low carbon steels10.1016/j.actamat.2014.10.010 ↗
34. The effects of a ferritic or martensitic matrix on the tensile behavior of a nano-precipitation strengthened ultra-low carbon Ti-Mo-Nb steel10.1016/j.msea.2020.140410 ↗
35. Austenite layer and precipitation in high Co–Ni maraging steel10.1016/j.micron.2014.07.008 ↗
36. Improvement of mechanical properties for low carbon ultra-high strength steel strengthened by Cu-rich multistructured precipitation via modification to bainite10.1016/j.msea.2021.141337 ↗
37. A statistical theory of solid solution hardening10.1002/pssb.19700410221 ↗
38. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
39. High-strength steels hardened mainly by nanoscale NiAl precipitates10.1016/j.scriptamat.2014.05.006 ↗
40. A novel low cost 2000 MPa grade ultra-high strength steel with balanced strength and toughness10.1016/j.msea.2019.05.039 ↗