Effects of pulse frequency and current density on microstructure and properties of biodegradable Fe-Zn alloy
Source abstract
Abstract
Novel Fe-Zn alloys were prepared by pulse electrodeposition to solve the low corrosion rate of iron-based biodegradable materials for vascular stents. The effects of frequency and current density on the composition, microstructure, hardness, and corrosion characteristics of alloys were studied. The results manifested that all the Fe-Zn alloys prepared under the conditions studied here were supersaturated solid solutions. The composition and microstructure of the alloys exhibited a strong dependence on the frequency and current density. When the pulse frequency increased from 50 to 1000 Hz, the zinc content in alloy decreased from 7.2 wt.% to 2.1 wt.% with the grain coarsening. Besides, the low-zinc alloy had low hardness due to its slight lattice distortion and grain boundary strengthening. When the peak current density increased from 10 to 13 A/dm2, the oxygen content in alloy increased from 0.1 wt.% to 1.4 wt.%, and the microstructure changed from coarse columnar grain to fine nanocrystalline with the hardness of the alloy increasing sharply. Electrochemical and immersion tests in simulated body fluid (SBF) demonstrated that the corrosion rates of Fe-Zn alloys were higher than that of pure iron. The alloy containing 4.6% Zn was more prone to corrosion (0.267 mm·y−1 in immersion test) than other alloys while keeping relatively low hardness. The intrinsic causes of zinc to the accelerated corrosion of electrodeposited ferroalloy should be attributed to the decrease of corrosion potential, the increase of local corrosion, and the weak protection barrier caused by the corrosion products.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Electrodeposition and Electroless Coatings · Corrosion Behavior and Inhibition · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (74)
Show source-provided references
1. Evolution of metallic cardiovascular stent materials: a comparative study among stainless steel, magnesium and zinc10.1016/j.biomaterials.2019.119641 ↗
2. Zinc-nutrient element based alloys for absorbable wound closure devices fabrication: current status, challenges, and future prospects10.1016/j.biomaterials.2021.121301 ↗
3. 20 - absorbable metals for cardiovascular applications, Editor(s): mitsuo Niinomi
4. Biodegradable stents for coronary artery disease treatment: recent advances and future perspectives10.1016/j.msec.2018.04.100 ↗
5. A good combination of ductility, strength, and corrosion resistance of fine-grained ZK60 magnesium alloy produced by repeated upsetting process for biodegradable applications10.1016/j.jallcom.2020.158334 ↗
6. Design and characterization of a novel biocorrodible iron-based drug-eluting coronary scaffold10.1016/j.matdes.2015.11.045 ↗
7. Recrystallization behavior, microstructure evolution and mechanical properties of biodegradable Fe–Mn–C(–Pd) TWIP alloys10.1016/j.actamat.2012.01.041 ↗
8. Bioresorbable scaffolds: unfulfilled prophecies10.1161/CIRCULATIONAHA.119.043773 ↗
9. Challenges in the use of zinc and its alloys as biodegradable metals: perspective from biomechanical compatibility10.1016/j.actbio.2019.07.038 ↗
10. Preclinical evaluation of a novel sirolimus-eluting iron bioresorbable coronary scaffold in porcine coronary artery at 6 months, JACC10.1016/j.jcin.2018.10.020 ↗
11. Surface characterization of Fe–10Al–25Mn alloy for biomaterial applications10.1016/j.jmrt.2021.08.006 ↗
12. A novel approach to temporary stenting: degradable cardiovascular stents produced from corrodible metal—results 6−18 months after implantation into New Zealand white rabbits10.1136/heart.86.5.563 ↗
13. Long-term biocompatibility of a corrodible peripheral iron stent in the porcine descending aorta10.1016/j.biomaterials.2006.05.029 ↗
14. Design strategy for biodegradable Fe-based alloys for medical applications10.1016/j.actbio.2009.07.039 ↗
15. Mechanism of acceleration of iron corrosion by a polylactide coating10.1021/acsami.8b17125 ↗
16. Accelerating degradation rate of pure iron by zinc ion implantation10.1093/rb/rbw020 ↗
17. Improvement of in vitro corrosion and cytocompatibility of biodegradable Fe surface modified by Zn ion implantation10.1016/j.apsusc.2017.01.158 ↗
18. Novel conjugated hybrid material for efficient lead(II) capturing from contaminated wastewater10.1016/j.msec.2019.04.015 ↗
19. Organic–inorganic based nano-conjugate adsorbent for selective palladium(II) detection, separation and recovery10.1016/j.cej.2014.08.028 ↗
20. A novel facial composite adsorbent for enhanced copper(II) detection and removal from wastewater10.1016/j.cej.2014.12.094 ↗
21. Long-term in vivo corrosion behavior, biocompatibility and bioresorption mechanism of a bioresorbable nitrided iron scaffold10.1016/j.actbio.2017.03.020 ↗
22. Electrodeposition of Fe–Mn alloys from chloride-based bath: a preliminary study for biomedical applications10.1016/j.jmrt.2021.05.103 ↗
23. Fe-Mn alloys for metallic biodegradable stents: degradation and cell viability studies10.1016/j.actbio.2009.11.025 ↗
24. In vitro and in vivo corrosion properties of new iron-manganese alloys designed for cardiovascular applications10.1002/jbm.b.33234 ↗
25. Manganese: recent advances in understanding its transport and neurotoxicity10.1016/j.taap.2007.03.001 ↗
26. Mechanical and corrosion properties of newly developed biodegradable Zn-based alloys for bone fixation10.1016/j.actbio.2011.05.008 ↗
27. Evolution of the degradation mechanism of pure zinc stent in the one-year study of rabbit abdominal aorta model10.1016/j.biomaterials.2017.08.022 ↗
28. Fe-Zn(Iron-Zinc)10.1007/s11669-007-9051-8 ↗
29. A study of degradation behaviour and biocompatibility of Zn—Fe alloy prepared by electrodeposition10.1016/j.msec.2020.111295 ↗
30. Mechanism for corrosion prevention by a mechanical plating of uniform Zinc-Iron alloy10.1007/s11665-016-2322-y ↗
31. Optimization of deposition conditions for development of high corrosion resistant Zn–Fe multilayer coatings10.1016/j.jmatprotec.2011.03.010 ↗
32. Relationship between the crystallographic structure of electrodeposited Fe-Zn alloy film and its thermal equilibrium diagram10.2320/matertrans.42.1969 ↗
33. Microstructure and in vitro biodegradable properties of Fe-Zn alloys prepared by electroforming10.4028/www.scientific.net/AMR.1033-1034.1200 ↗
34. Effects of electrodeposition conditions and heat treatment on microstructure of Fe-5Zn alloy
35. Influence of bath composition on microstructure and properties of electrodeposited Fe-Zn alloy coating
36. Effects of pulse plating parameters on the microstructure and properties of high frequency pulse electrodeposited Ni-Co/ZrO2 nanocomposite coatings10.1007/s10854-016-5565-3 ↗
37. The mechanical behavior of a layered nanostructured Ni with an alternating growth of ultrafine grains and nano-sized grains fabricated by electrodeposition10.1016/j.msea.2017.11.122 ↗
38. Enhanced mechanical properties of multilayered Cu with modulated grain size distribution10.1002/adem.201700849 ↗
39. Pulse and pulse reverse plating—conceptual, advantages and applications10.1016/j.electacta.2007.11.054 ↗
40. Effect of current density and agitation modes on the structural and corrosion behavior of Ni/diamond composite coatings10.1016/j.jmrt.2021.03.084 ↗
41. Effects of peak current density on the mechanical properties of nanocrystalline Ni-Co alloys produced by pulse electrodeposition10.1016/j.apsusc.2008.04.087 ↗
42. Dendritic Ag–Fe nanocrystalline alloy synthesized by pulsed electrodeposition and its characterization10.1016/j.apsusc.2014.08.039 ↗
43. Influence of pulse frequency on physicochemical properties of InSb films obtained via electrodeposition10.1016/j.electacta.2019.02.111 ↗
44. Fabrication of Ni-Co-SiC composite coatings by pulse electrodeposition — effects of duty cycle and pulse frequency10.1016/j.surfcoat.2012.11.059 ↗
45. The influence of pulsed electroplating frequency and duty cycle on copper film microstructure and Stress State10.1016/j.tsf.2016.11.047 ↗
46. Effects of duty ratio on properties of Ni-P-(sol)Al2O3 coating prepared by pulse-assisted chemical deposition10.1016/j.jmrt.2021.08.077 ↗
47. Electrocrystallization in pulse electrolysis10.1016/0376-4583(78)90044-4 ↗
48. Effects of pulse electrodeposition parameters on the properties of Ni–TiO2 nanocomposite coatings10.1016/j.apsusc.2010.04.088 ↗
49. The influence of pulse plating parameters on the hardness and wear resistance of nickel–alumina composite coatings10.1016/j.surfcoat.2004.09.023 ↗
50. Microstructure and tribological properties of electrodeposited Ni–Co alloy deposits10.1016/j.apsusc.2004.08.033 ↗
51. Electrodeposition of nanocrystalline Ni-Fe alloys10.1016/0965-9773(95)00264-F ↗
52. Oxygen incorporation during the electrodeposition of Ni, Fe, and Ni-Fe alloys10.1149/1.1838861 ↗
53. Strategy for electrodeposition of highly ductile bulk nanocrystalline metals with a face-centered cubic structure10.2320/matertrans.M2014268 ↗
54. Effect of electrodeposition current density on the microstructure and the degradation of electroformed iron for degradable stents10.1016/j.mseb.2011.02.031 ↗
55. Template assisted electrochemical growth of cobalt nanowires: influence of deposition conditions on structural, optical and magnetic properties10.1166/jnn.2011.3826 ↗
56. Influence of solution pH and concentration of saccharin on electrodeposition and properties of 2.4 T CoFe alloys10.1149/1.3194773 ↗
57. Stress control in electrodeposited CoFe films—experimental study and analytical model10.1016/j.electacta.2012.07.087 ↗
58. Stress evolution in CoxFe1−x (x = 0.33–0.87) electrodeposited films10.1016/j.electacta.2010.07.100 ↗
59. Effect of electrolyte composition and deposition current for Fe/Fe-P electroformed bilayers for biodegradable metallic medical applications10.1016/j.msec.2016.08.026 ↗
60. 1991
61. Uniform and pitting corrosion events induced by SCN anions on Al alloys surfaces and the effect of UV light10.1016/j.electacta.2010.12.045 ↗
62. Modification of in vitro degradation behavior of pure iron with ultrasonication treatment: comparison of two different pseudo-physiological solutions10.1016/j.msec.2018.10.079 ↗
63. Accelerated degradation behavior and cytocompatibility of pure iron treated with sandblasting10.1021/acsami.6b07068 ↗
64. The initiation and formation of a double-layer phosphate conversion coating on steel10.1016/j.elecom.2020.106676 ↗
65. Comparative studies on degradation behavior of pure zinc in various simulated body fluids
66. Comparative studies of Tris-HCl, HEPES and NaHCO3/CO2 buffer systems on the biodegradation behaviour of pure Zn in NaCl and SBF solutions10.1016/j.corsci.2019.05.018 ↗
67. Comparative corrosion behavior of Zn with Fe and Mg in the course of immersion degradation in phosphate buffered saline10.1016/j.corsci.2016.05.039 ↗
68. An electrochemical impedance spectroscopy study of the corrosion behaviour of PVD coated steels in 0.5 N NaCl aqueous solution: Part I. Establishment of equivalent circuits for EIS data modelling10.1016/S0010-938X(02)00213-5 ↗
69. Plasma modified Mg–Nd–Zn–Zr alloy with enhanced surface corrosion resistance10.1016/j.corsci.2013.09.007 ↗
70. 2005
71. Martensitic transformations and mechanical and corrosion properties of Fe-Mn-Si alloys for biodegradable medical implants10.1007/s11661-017-4458-2 ↗
72. Exploring the role of manganese on the microstructure, mechanical properties, biodegradability, and biocompatibility of porous iron-based scaffolds10.1021/acsbiomaterials.8b01497 ↗
73. Degradation of biodegradable implants: the influence of microstructure and composition of Mg-Zn-Ca alloys10.1016/j.jallcom.2018.09.346 ↗
74. Novel Zn-based alloys for biodegradable stent applications: design, development and in vitro degradation10.1016/j.jmbbm.2016.03.018 ↗