journal article·2023-11Open access

Room temperature creep mechanisms of Ti–6Al–4V ELI alloy with equiaxed microstructure under different applied stresses

Mengmeng Zhang, Jianke Qiu, Chao Fang, Mingjie Zhang, Yingjie Ma, Zhiqing Yang, Jiafeng Lei, Rui Yang

Abstract

Titanium alloys are often used to make deep-sea pressure hulls and the creep strain produced during service is nonnegligible. The variation of dislocation structures with room temperature creep stresses in equiaxed α grains of Ti-6Al-4V ELI alloy was examined using transmission electron microscope. The plastic deformation mechanism varied with the applied stress, mainly manifested by the change of dislocation patterns and the sequential activation of slip systems. At the stress below the creep threshold, even though almost no macroscopic creep was generated, a small number of immobile dislocations and dislocation networks occurred in the sample. The networks were composed of dislocations with different Burgers vectors, and part of them would evolve into low angle grain boundaries (LAGBs). At the stresses above the threshold, the density of dislocations in α grains increased with the stress level, and the basal , pyramidal and slips were activated successively which also contributed to creep and participated in the formation of LAGBs. Prismatic slip was always the predominant creep deformation mechanism for the studied stress range. The activation of difficult slip systems was attributed to the stress concentration and stress redistribution between soft and hard phases/grains. In general, the amount of LAGBs increased with the applied creep stress, but the LAGBs formed by dislocation networks decreased.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Hydrogen embrittlement and corrosion behaviors in metals · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (54)

Show source-provided references
1. Lütjering · 2007
2. A constitutive model for a rate and temperature-dependent, plastically anisotropic titanium alloy10.1016/j.ijplas.2020.102777 ↗
3. Deformation induced anisotropic responses of Ti–6Al–4V alloy. Part I: experiments10.1016/j.ijplas.2012.03.015 ↗
4. Microstructure, creep, and tensile deformation in Ti-6Al-2Nb-1Ta-0.8Mo10.1007/BF02646658 ↗
5. The temperature and stress dependent primary creep of CP-Ti at low and intermediate temperature10.1016/j.msea.2014.05.094 ↗
6. Time dependent twinning during ambient temperature creep of α Ti-Mn alloy10.1016/0956-716X(94)90203-8 ↗
7. The effects of stress level and grain size on the ambient temperature creep deformation behavior of an alpha Ti-1.6 wt pct V alloy10.1007/s11661-005-0179-z ↗
8. Modeling interstitial diffusion controlled twinning in alpha titanium during low-temperature creep10.1016/j.scriptamat.2011.06.049 ↗
9. The effect of time-dependent twinning on low temperature (<0.25∗Tm) creep of an alpha-titanium alloy10.1016/j.ijplas.2008.06.002 ↗
10. Observations of room-temperature creep recovery in titanium alloys10.1007/s11661-002-0159-5 ↗
11. Advances in low-temperature (<0.25Tm) creep behavior of single and two-phase titanium alloys10.1016/j.proeng.2013.03.212 ↗
12. Observation of etch-pits and LAGB configurations during ambient creep of Ti-6Al-4V alloy10.1007/s11661-016-3443-5 ↗
13. Observation of tension-compression asymmetry in α and titanium alloys10.1080/14786430412331315707 ↗
14. Presences of primary creep in various phase metals and alloys at ambient temperature10.1016/j.msea.2004.01.146 ↗
15. Mechanisms of primary creep in α/β titanium alloys at lower temperatures10.1016/S0921-5093(97)00322-5 ↗
16. Dislocation interactions and crack nucleation in a fatigued near-alpha titanium alloy10.1016/j.ijplas.2018.06.009 ↗
17. Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys, part II: creep deformation10.1007/BF02586108 ↗
18. The role of dwell hold on the dislocation mechanisms of fatigue in a near alpha titanium alloy10.1016/j.ijplas.2020.102743 ↗
19. Slip activity during low-stress cold creep deformation in a near-α titanium alloy10.1016/j.actamat.2022.117691 ↗
20. The roles of rise and fall time in load shedding and strain partitioning under the dwell fatigue of titanium alloys with different microstructures10.1016/j.ijplas.2021.103161 ↗
21. Texture induced planar anisotropy of dwell fatigue response in titanium: insights from experiments and crystal plasticity simulations10.1016/j.ijplas.2021.103140 ↗
22. Phenomenological and microstructural analysis of room temperature creep in titanium alloys10.1016/S1359-6454(99)00426-7 ↗
23. Creep anisotropy characteristics and microstructural crystallography of marine engineering titanium alloy Ti6321 plate at room temperature10.1016/j.msea.2022.143728 ↗
24. Short-range order (SRO) and its effect on the primary creep behavior of a Ti–6wt.%Al alloy10.1016/S0921-5093(01)01045-0 ↗
25. Observation and analysis of weak-fringing faults in Ti-6 wt% Al10.1080/01418610208243202 ↗
26. Intragranular deformation mechanisms during ambient-temperature creep in hexagonal close-packed metals10.2320/matertrans.M2009224 ↗
27. Low temperature creep of Ti-6Al-4V10.1007/BF02644335 ↗
28. Influence of complex LCF and dwell load regimes on fatigue of Ti–6Al–4V10.1016/j.actamat.2015.09.014 ↗
29. Humphreys · 2004 · 91
30. Dwell fatigue microstructure in a near-α titanium alloy10.1007/s11661-007-9105-x ↗
31. Hexagonal dislocation networks in titanium10.1007/BF02644025 ↗
32. Dislocation structure of non-habit plane of α precipitates in a Ti–7.26 wt.% Cr alloy10.1016/j.actamat.2005.10.017 ↗
33. Creep mechanisms in Ti–3Al–2.5V alloy tubing deformed under closed-end internal gas pressurization10.1016/j.actamat.2008.01.052 ↗
34. Creep of Ti–5Al–5Mo–5V–1Fe–1Cr alloy with equiaxed and lamellar microstructures10.1016/j.msea.2015.10.092 ↗
35. Effect of trace impurities on the creep behavior of a near α titanium alloy10.1016/j.scriptamat.2008.05.009 ↗
36. Low temperature creep plasticity10.1016/j.jmrt.2014.06.009 ↗
37. Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy10.1016/j.actamat.2017.05.015 ↗
38. Anisotropy in the plastic flow properties of single-crystal α titanium determined from micro-cantilever beams10.1016/j.actamat.2009.07.064 ↗
39. Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization10.1016/j.actamat.2020.03.003 ↗
40. Temperature and stain rate effect on the deformation of nanostructured pure titanium10.1016/j.ijplas.2015.04.002 ↗
41. Slip transfer and deformation structures resulting from the low cycle fatigue of near-alpha titanium alloy Ti-6242Si10.1016/j.ijplas.2017.09.012 ↗
42. Combined strengthening from nanotwins and nanoprecipitates in an iron-based superalloy10.1016/j.actamat.2018.04.001 ↗
43. Mechanical behavior, deformation mechanism and microstructure evolutions of ultrafine-grained Al during recovery via annealing10.1016/j.msea.2019.138706 ↗
44. The role of pyramidal dislocations in the grain refinement mechanism in Ti-6Al-4V alloy processed by severe plastic deformation10.1016/j.actamat.2020.08.076 ↗
45. Additional dislocation slip determined excess yield stress in titanium10.1016/j.msea.2022.144387 ↗
46. Structural evolutions of metallic materials processed by severe plastic deformation10.1016/j.mser.2018.06.001 ↗
47. Grain size effect on deformation twinning propensity in ultrafine-grained hexagonal close-packed titanium10.1016/j.scriptamat.2013.06.001 ↗
48. Crystal plasticity modeling of slip activity in Ti–6Al–4V under high cycle fatigue loading10.1016/j.ijplas.2008.08.004 ↗
49. The effect of metastability on room temperature deformation behavior of β and α + β titanium alloys10.1007/s10853-009-4178-0 ↗
50. Dwell fatigue in two Ti alloys: an integrated crystal plasticity and discrete dislocation study10.1016/j.jmps.2016.08.008 ↗
51. The formation of cracks as a result of plastic flow
52. Perspective on hetero-deformation induced (HDI) hardening and back stress
53. Chapter four - fundamentals of heterostructured materials
54. Dislocation array reflection enhances strain hardening of a dual-phase heterostructured high-entropy alloy10.1080/21663831.2023.2208166 ↗