Influence of Ti addition on the microstructure and comprehensive properties of Mo–Cu alloy
Source abstract
Abstract
To enhance the overall performance of Mo–Cu alloy, Ti was added to Mo–Cu alloy to improve the bonding strength of Mo/Cu interface and generate solid solution strengthening effect. The outstanding performances of Mo–Cu–Ti alloys were achieved by infiltrating Cu–Ti alloy with different compositions into the Mo skeleton. Compared to the incoherent interface of Mo/Cu in Mo–Cu alloy, the addition of Ti transformed its interface to the coherent interface of Mo–Ti/Cu–Ti. All Mo–Cu–Ti alloy blocks had higher relative densities (97.4%∼98.5%) to guarantee the excellent comprehensive performances. What's more, the existences of Mo–Ti and Cu–Ti solid solutions assured the alloy possessed relatively high mechanical strength. The introduction of Ti purified the grain boundary by absorbing oxygen to generate TiO2 which hindered the growth of Mo–Ti grains. As increasing Ti amount from 0 wt% to 4.62 wt%, the Mo–Ti (or Mo) grain size reduced from 5 μm to 4.1 μm. Notably, Mo–Cu alloy block with the addition of 2.30 wt% Ti possessed the highest tensile strength of 562 MPa. Additionally, since the finer grain size of Mo–Ti alloy, this sample also owned the maximum micro-hardness and bending strength of 268 HV and 1730 MPa, respectively. Nevertheless, the presences of Cu–Ti solid solution and TiO2 also destroyed the electrical conductivities of the samples to some extent.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced materials and composites · Aluminum Alloys Composites Properties · Fusion materials and technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (95)
Show source-provided references
1. Activated liquid phase sintering of W-Cu and Mo-Cu10.1016/j.ijrmhm.2015.04.030 ↗
2. Cu-Mo composite powders obtained by combustion-coreduction process10.1016/j.ijrmhm.2015.09.002 ↗
3. Effect of Fe on the sintering and thermal properties of Mo-Cu composites10.1016/j.matdes.2009.09.014 ↗
4. Fabrication of homogeneous Mo-Cu composites using spherical molybdenum powders prepared by thermal plasma spheroidization process10.1016/j.ijrmhm.2018.01.022 ↗
5. Fabrication of Mo-Cu composites by a diffusion-rolling procedure10.1016/j.ijrmhm.2013.11.003 ↗
6. Liquid phase sintering of mechanically alloyed Mo-Cu powders10.1016/j.msea.2017.06.090 ↗
7. Microstructures of sintered Mo-Cu alloys with mechanically activated powder
8. Microwave-assisted synthesis of Mo-Cu nano-powders at an ultra-low temperature and their sintering properties10.1016/j.matchemphys.2014.08.026 ↗
9. Preparation and controllability of Cu particles on annealed Mo-Cu alloy films10.1016/j.matlet.2019.07.044 ↗
10. The thermo-mechanical behaviour of W-Cu metal matrix composites for fusion heat sink applications: the influence of the Cu content10.1016/j.jnucmat.2017.08.020 ↗
11. Processing and microstructure of functionally graded W/Cu composites fabricated by multi-billet extrusion using mechanically alloyed powders10.1016/j.compscitech.2005.11.034 ↗
12. Fabrication of W-Cu functionally graded materials with high density by particle size adjustment and solid state hot press10.1016/j.compscitech.2007.10.023 ↗
13. Corrosion and wear properties of TiC/Ni-Mo composites produced by direct consolidation during a self-propagating high-temperature reaction10.1016/S0266-3538(00)00194-9 ↗
14. Massalski · 1986
15. Solubility effects on grain growth and thermal conductivity of liquid phase-sintered Mo-Cu
16. Fabrication of W/Cu and Mo/Cu FGM as plasma-facing materials
17. The effects of composition and microstructure on the thermal conductivity of liquid-phase-sintered W-Cu10.1007/s11661-010-0210-x ↗
18. Effect of Fe content on the microstructure and properties of Mo-Cu alloy
19. Strengthening mechanism and hot deformation behavior of 20%Mo/Cu-Al2O3 composite
20. Kirkendall porosity during thermal treatment of Mo-Cu nano multilayers10.1016/j.msea.2007.01.037 ↗
21. Effect of Fe on the constitution of Cu-W alloys at 1200°C10.1016/S0925-8388(03)00434-1 ↗
22. Modeling of thermal stresses in a graded Cu/W joint10.1016/S0022-3115(02)00820-6 ↗
23. Sintering behavior of molybdenum-copper and tungsten-copper alloys by using ultrafine molybdenum and tungsten powders as raw materials10.1016/j.ijrmhm.2020.105194 ↗
24. Preparation and properties of W-30 wt% Cu alloy with the additions of Ni and Fe elements10.1016/j.jallcom.2022.167040 ↗
25. Preparation and properties of multiphase solid-solution strengthened high-performance W-Cu alloys through alloying with Mo, Fe and Ni10.1016/j.msea.2023.144909 ↗
26. Microstructure and mechanical properties of Mo-Cu-Zr composites fabricated via microwave sintering10.1016/j.jallcom.2020.156120 ↗
27. Novel function-structure-integrated Ti-Mo-Cu alloy combined with excellent antibacterial properties and mechanical compatibility as implant application10.1016/j.jallcom.2023.169323 ↗
28. A high strength and high electrical conductivity Cu-Cr-Zr alloy fabricated by cryorolling and intermediate aging treatment10.1016/j.msea.2016.10.087 ↗
29. Correlation of viscosity with atomic packing in Cu50Zr50 melt10.1016/j.molliq.2019.111544 ↗
30. Anomalously slow crystal growth of the glass-forming alloy CuZr10.1038/nmat3631 ↗
31. Cu-Zr (Copper-Zirconium)10.1007/s11669-012-0077-1 ↗
32. Effect of alloying elements Ti, Zr on the property and microstructure of molybdenum10.1016/j.ijrmhm.2008.03.006 ↗
33. Effect of alloyed elements Ti, Zr on the property and microstructure of Mo alloy
34. Low-temperature tensile behavior of powder-metallurgy Mo-Ti Alloys10.1016/0263-4368(93)90051-G ↗
35. Studies on the development of protective coating on TZM alloy and its subsequent characterization10.1016/j.jmatprotec.2007.12.075 ↗
36. Preparation of nanostructured high- temperature TZM alloy by mechanical alloying and sintering10.1016/j.ijrmhm.2010.09.003 ↗
37. Hardening behavior of dilute Mo-Ti alloys by two-step heat-treatment10.1016/j.ijrmhm.2006.03.005 ↗
38. Preparation and characterization of W-Cu nanopowders by a homogeneous precipitation process10.1016/j.jallcom.2005.08.087 ↗
39. Recent progress in development of tungsten copper composites: synthesis, modification, and applications10.1016/j.ijrmhm.2018.03.014 ↗
40. Tungsten-copper composite production by activated sintering and infiltration10.1016/j.ijrmhm.2011.03.009 ↗
41. Investigation of solid solution hardening in molybdenum alloys10.1016/j.ijrmhm.2010.05.010 ↗
42. Interpretation and use of standard atomic weights (IUPAC Technical Report)10.1515/pac-2017-1002 ↗
43. Mechanical properties and microstructures of W-1%Y2O3 microalloyed with Zr10.1016/j.msea.2016.02.072 ↗
44. Transient thermal shock behavior of W-Zr/Sc2O3 composites prepared via spark plasma sintering10.1016/j.fusengdes.2017.11.012 ↗
45. Synthesis and characterization of nano TiC dispersed strengthening W alloys via freeze-drying10.1016/j.jallcom.2020.157774 ↗
46. Microstructure refinement and mechanical properties improvement in the W-Y2O3 alloys via optimized freeze-drying10.1016/j.ijrmhm.2020.105453 ↗
47. Coupling effect of intergranular and intragranular particles on ductile fracture of Mo-La2O3 alloys10.1016/j.msea.2015.05.032 ↗
48. Low cycle fatigue behaviors of pure Mo and Mo-La2O3 alloys10.1016/j.msea.2017.09.064 ↗
49. Preparation and properties of Al2O3 dispersed fine-grained W-Cu alloy10.1016/j.apt.2022.103523 ↗
50. Chen · 1994
51. Study of a Mo-Cu pseudoalloy obtained from mechanically activated charge10.1007/s11041-007-0084-8 ↗
52. Preparation and characterization of Mo-15 Cu superfine powders by a gelatification-reduction process10.1016/j.jallcom.2008.09.097 ↗
53. Fabrication of Mo-Cu alloys by resistance sintering under ultra-high pressure
54. Temperature dependent tensile and fracture behaviors of Mo-10 wt.% Cu composite10.1016/j.ijrmhm.2013.08.012 ↗
55. Yang · 2020 · vol. 44 · 52
56. Fabrication of fine-grained Mo-Cu alloy
57. Design of stable nanocrystalline alloys10.1126/science.1224737 ↗
58. Alloy effects in nanostructures10.1016/0965-9773(93)90088-S ↗
59. Alloy thermodynamics in nanostructures10.1557/JMR.1994.0004 ↗
60. Influence of minor Ti additive on the microstructure and mechanical properties of Mo based alloys
61. The mechanical properties of the Mo-0.5Ti and Mo-0.1Zr alloys at room temperature and high temperature annealing, High Temp
62. Effect of mechanical alloying on the microstructure and properties of W-Ti alloys fabricated by spark plasma sintering10.1016/j.powtec.2016.08.039 ↗
63. Refined microstructure and enhanced mechanical properties in Mo-Y2O3 alloys prepared by freeze-drying method and subsequent low temperature sintering10.1016/j.jmst.2021.01.064 ↗
64. Strengthening mechanisms of Mo-La2O3 alloys processed by solid-solid doping and vacuum hot-pressing sintering10.1016/j.vacuum.2018.03.012 ↗
65. Fabrication of ultrafine-grain and great-performance W-Ni-Fe alloy with medium W content10.1016/j.jallcom.2020.156237 ↗
66. Chapter 8 - strengthening and toughening
67. Substitutional solution hardening10.1016/0001-6160(63)90213-X ↗
68. Microstructure and mechanical properties of nano-size zirconium carbide dispersion strengthened tungsten alloys fabricated by spark plasma sintering method10.1088/1009-0630/17/12/15 ↗
69. The synthesis of TiC dispersed strengthened Mo alloy by freeze-drying technology and subsequent low temperature sintering10.1016/j.scriptamat.2021.113831 ↗
70. Ultra-fine W-Y2O3 composite powders prepared by an improved chemical co-precipitation method and its interface structure after spark plasma sintering10.1007/s42864-019-00021-w ↗
71. Moerkurova · 1984
72. Synthesis of W-Y2O3 alloys by freeze-drying and subsequent low temperature sintering: microstructure refinement and second phase particles regulation10.1016/j.jmst.2019.08.010 ↗
73. Achieving high strength and ductility in ODS-W alloy by employing oxide@W core-shell nanopowder as precursor10.1038/s41467-021-25283-2 ↗
74. Strengthening materials by engineering coherent internal boundaries at the nanoscale10.1126/science.1159610 ↗
75. Mechanical properties II -strengthening and toughening
76. Stacking-fault strengthening of biomedical Co-Cr-Mo alloy via multipass thermomechanical processing10.1038/s41598-017-10305-1 ↗
77. Microstructure and mechanical properties of nanostructured Al-4Cu alloy produced by mechanical alloying and vacuum hot pressing10.1007/s11661-009-0005-0 ↗
78. The simultaneous improvements of strength and ductility in W-Y2O3 alloy obtained via an alkaline hydrothermal method and subsequent low temperature sintering10.1016/j.msea.2020.139329 ↗
79. Thermal stability and high-temperature mechanical performance of nanostructured W-Cu-Cr-ZrC composite10.1016/j.compositesb.2020.108600 ↗
80. Nanostructured highstrength molybdenum alloys with unprecedented tensile ductility10.1038/nmat3544 ↗
81. The combination of atomic size and elastic modulus misfit interactions in solid solution hardening10.1016/0036-9748(81)90257-X ↗
82. A statistical theory of solid solution hardening10.1002/pssb.19700410221 ↗
83. Investigation of solid solution hardening in molybdenum alloys10.1016/j.ijrmhm.2010.05.010 ↗
84. Nano Mo-La-O particles strengthened Mo alloys fabricated via freeze-drying technology and low temperature sintering10.1016/j.msea.2021.141448 ↗
85. In-situ Al2O3-Al interface contribution towards the strength-ductility synergy of Al-CuO composite fabricated by solid-state reactive sintering10.1016/j.scriptamat.2021.113825 ↗
86. Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction10.1016/j.actamat.2020.116524 ↗
87. W-Y2O3 composite nanopowders prepared by freeze drying method and its sintering characteristics10.1016/j.jallcom.2019.07.214 ↗
88. Effect of nano-sized ZrO2 on the recrystallization of Mo alloy10.1016/j.jallcom.2018.04.155 ↗
89. Microstructure and high temperature deformation behavior of the Mo-ZrO2 alloys10.1016/j.jallcom.2017.05.013 ↗
90. Thermomechanical processing, microstructure and tensile properties of atungsten heavy alloy10.1016/j.msea.2014.06.072 ↗
91. Microstructure and strengthening mechanism of grain boundary strengthened W-ZrB2 alloy10.1016/j.jmrt.2020.02.027 ↗
92. Modeling of the sliding resistance of Σ3⟨111⟩tungsten grain boundary: influence of boron additive
93. Influence of the interface strength on the mechanical properties of discontinuous tungsten fiber-reinforced tungsten composites produced by field assisted sintering technology10.1016/j.compositesa.2018.01.022 ↗
94. Characterization of ductile phase toughening mechanisms in a hot-rolled tungsten heavy alloy10.1016/j.actamat.2020.116523 ↗
95. The preparation of TiC dispersion strengthened tungsten alloy via freeze-drying method10.1088/2053-1591/ab51bc ↗