journal article·2021-11Open access

Hot deformation behavior and processing parameters optimization of SP700 titanium alloy

Qian Qiu, Kelu Wang, Xin Li, Jun Wang, Xin Gao, Kaiming Zhang

Abstract

The Gleeble-3800 thermal simulator is used to perform isothermal and constant strain rate compression tests on SP700 titanium alloy under the conditions of deformation temperature of 700–950 °C and strain rate of 0.001–1 s−1. The processing map technology can be obtained based on dynamic material model, through this technology, its thermal deformation behavior can be studied and the appropriate processing parameter range can be optimized by combining the changes in the strain rate sensitivity exponent m, strain hardening exponent n and deformation activation energy Q. The results show that the flow stress of SP700 titanium alloy is sensitive to deformation temperature and strain rate. When the strain is 0.9, the strain rate sensitivity exponent m is greater than 0.5 when the deformation temperature is 800 °C and the strain rate is 0.001 s−1 and 1 s−1. Under this condition, the SP700 titanium alloy may have superplastic deformed. In addition, the analysis shows that when the deformation temperature is 775–825 °C, the strain rate is 0.3–1 s−1 and 0.001–0.002 s−1, this condition is the best processing parameter range of SP700 titanium alloy.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metallurgy and Material Forming · Titanium Alloys Microstructure and Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Development and applications of titanium alloy SP-700 with high formability10.1520/JTE12683J ↗
2. Improvement in fracture toughness of Ti-4.5Al-3V-2Fe-2Mo through micro structural optimization10.1007/s11661-003-0328-1 ↗
3. Effect of heat treatment process on structure and properties of SP-700 titanium alloy
4. Mechanical properties of Ti-4.5Al-3V-2Mo-2Fe and possibility for healthcare applications10.1016/j.msec.2004.12.012 ↗
5. Processing maps for hot working of titanium alloys10.1016/S0921-5093(97)00782-X ↗
6. Hot working of commercial Ti-6Al-4V with an equiaxed α-β microstructure: materials modeling considerations10.1016/S0921-5093(00)00741-3 ↗
7. Hot deformation behavior of Zr-2.5Nb alloy: a comparative study using different materials models10.1016/j.jallcom.2015.11.183 ↗
8. Hot deformation behaviors and optimization of processing parameters for Alloy 602 CA10.1016/j.jallcom.2018.08.144 ↗
9. Characterization of hot deformation behavior of alloy 617 through kinetic analysis, dynamic material modeling and microstructural studies10.1016/j.msea.2016.04.004 ↗
10. Characterization on hot deformation behavior of Ti-22Al-25Nb alloy using a combination of 3D processing maps and finite element simulation method10.1016/j.jallcom.2018.04.225 ↗
11. Processing maps for the Cu-Cr-Zr-Y alloy hot deformation behavior10.1016/j.msea.2016.03.033 ↗
12. Deformation behavior and processing maps of Ni3Al-based superalloy during isothermal hot compression10.1016/j.jallcom.2017.04.116 ↗
13. Effect of Zr addition on the mechanical properties and superplasticity of a forged SP700 titanium alloy10.3390/ma14040906 ↗
14. Microtwin formation in the α phase of duplex titanium alloys affected by strain rate10.1016/j.msea.2010.12.027 ↗
15. Superplastic deformation microstructure and property of laser welded Ti-4.5Al-3V-2Fe-2Mo alloy
16. Flow behavior and 3D processing map for hot deformation of Ti-2.7Cu alloy10.1016/j.jmrt.2019.12.093 ↗
17. Behavior of adiabatic shear and flow localization of alloy Ti-6.5Al-3.5Mo-1.5Zr-0.3Si
18. The hot deformation behavior and processing map of Ti-47.5Al-Cr-V alloy10.1016/j.matdes.2015.07.027 ↗
19. Hot deformation behavior and processing parameter optimization of Ti60 alloy
20. High strain rate superplasticity via friction stir processing (FSP): a review10.1016/j.msea.2021.141499 ↗
21. Superior low-temperature superplasticity in fine-grained ZK60 Mg alloy sheet produced by a combination of repeated upsetting process and sheet extrusion10.1016/j.msea.2021.141444 ↗
22. Superplastic deformation mechanical behavior and constitutive modelling of a near-α titanium alloy TNW700 sheet10.1016/j.msea.2021.141419 ↗
23. Hot compressive deformation behavior of TC4 titanium alloy
24. Flow behavior and deformation mechanism in the isothermal compression of the TC8 titanium alloy10.1016/j.msea.2014.02.002 ↗
25. Effect of temperature and strain rate on the workability of FGH4096 superalloy in hot deformation10.1016/j.matdes.2016.01.032 ↗
26. Hot deformation behaviour of 7075 alloy10.1016/j.jallcom.2010.09.139 ↗
27. Strain rate sensitivity and strain hardening exponent during the isothermal compression of Ti60 alloy10.1016/j.msea.2012.01.021 ↗
28. Strain hardening and plastic flow properties of nitrogen-alloyed Fe-17Cr- (8-10) Mn-5Ni austenitic stainless steels10.1016/S1359-6454(96)00343-6 ↗
29. Tensile deformation
30. The variation of strain rate sensitivity exponent and strain hardening exponent in isothermal compression of Ti-6Al-4V alloy10.1016/j.matdes.2009.09.055 ↗
31. Development of processing maps for 6061 Al/15% SiCp composite material10.1016/j.msea.2003.11.019 ↗
32. High temperature flow behaviour of SiC reinforced lithium aluminosilicate composites10.1007/BF02710104 ↗
33. Construction of processing maps based on expanded data by BP-ANN and identification of optimal deforming parameters for Ti-6Al-4V alloy10.1007/s12541-016-0022-z ↗
34. Analysis of high temperature flow stress of titanium alloys IMI 550 and Ti-10V-2Fe-3Al during isothermal forging10.1179/mst.1998.14.4.339 ↗
35. Prasad · 2015
36. Modeling of dynamic material behavior in hot deformation: forging of Ti-624210.1007/BF02664902 ↗