journal article·2022-03Open access

Enhancement of electrical conductivity and corrosion resistance by gold-nickel coating of additively manufactured AlSi10Mg alloy

Timo Rautio, Hamidreza Torbati-Sarraf, Tarek Allam, Antti Järvenpää, Atef Hamada

Abstract

Gold-nickel coatings (Au–Ni) were applied by electrodeposition (ED) and electroless deposition (ELD) on additively manufactured (AM) AlSi10Mg alloy to improve the electrical conductivity and electrochemical behavior. Characterization of the Au–Ni coatings was performed by a scanning electron microscope equipped with energy dispersive X-ray spectroscopy (EDS) and x-ray diffraction to study the tiny features. The surface indentation hardness of the coated alloy was evaluated to study the coating strength. The electrochemical behavior of the as-built part and its counterpart, Au–Ni coated surfaces, were evaluated by conducting potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) in a 3.5% NaCl solution. The results revealed that the Au–Ni coatings with layers thickness of ∼2 and 10 μm, respectively, could overcome the surface critical defects, i.e., pores and flaws. The surface hardness of the coated AM alloy has significantly increased six times due to the hard Ni layer. The electrochemical measurements showed a significant decrease in the anodic dissolution rate and increase in pitting corrosion resistance for the Au–Ni coated surfaces compared to the bare AM AlSi10Mg alloy with the as-built and polished surface condition in chloride solution. This was attributed to the stability of the Au–Ni coatings against the anodic overpotential. Moreover, it was observed that the Au–Ni coatings reduce the electrical resistance of the studied AM alloy by 40%. Consequently, the surface electrical conductivity property of the AM AlSi10Mg alloy was enhanced by both Au–Ni coating procedures.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (68)

Show source-provided references
1. Additive manufacturing tooling for the automotive industry10.1007/s00170-017-0239-8 ↗
2. Life cycle assessment of an additive manufactured automotive component
3. Additive manufacturing of low-cost porous titanium-based composites for biomedical applications: advantages, challenges and opinion for future development10.1016/j.jallcom.2020.154263 ↗
4. Additive manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry10.1016/j.phpro.2010.08.082 ↗
5. The present and future of additive manufacturing in the aerospace sector: a review of important aspects
6. Froes · 2019
7. Improving the fatigue behaviour of a selectively laser melted aluminium alloy: influence of heat treatment and surface quality10.1016/j.matdes.2016.05.041 ↗
8. Disk laser assisted surface heat treatments of alsi10mg parts produced by selective laser melting (slm)10.1016/j.promfg.2019.08.014 ↗
9. A comparison of fatigue strength sensitivity to defects for materials manufactured by AM or traditional processes10.1016/j.ijfatigue.2016.06.020 ↗
10. Additive manufacturing of fatigue resistant materials: challenges and opportunities10.1016/j.ijfatigue.2017.01.001 ↗
11. Microstructure of selective laser melted CM247lc nickel based superalloy and its evolution through heat treatment10.1016/j.matchar.2016.02.004 ↗
12. An integrated approach of topology optimized design and selective laser melting process for titanium implants materials
13. Additive manufacturing of ultrafine-grained high-strength titanium alloys10.1038/s41586-019-1783-1 ↗
14. Selective laser melting of high aspect ratio 3D nickel–titanium structures two way trained for MEMS applications10.1007/s10999-007-9032-4 ↗
15. Effect of structural support on microstructure of nickel base superalloy fabricated by laser-powder bed fusion additive manufacturing10.1016/j.addma.2018.12.017 ↗
16. Further studies in selective laser melting of stainless and tool steel powders10.1016/j.ijmachtools.2006.09.013 ↗
17. Tailoring the nanostructure of laser powder bed fusion additively manufactured maraging steel10.1016/j.addma.2020.101561 ↗
18. High power selective laser melting (HP SLM) of aluminum parts10.1016/j.phpro.2011.03.035 ↗
19. 3D printing of Aluminium alloys: additive Manufacturing of Aluminium alloys using selective laser melting10.1016/j.pmatsci.2019.100578 ↗
20. High power selective laser melting (HP SLM) of aluminum parts10.1016/j.phpro.2011.03.035 ↗
21. Selective laser melting of AlSi10mg alloy: process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
22. Laser welding of alsi10mg aluminium-based alloy produced by selective laser melting (slm)10.1016/j.promfg.2019.08.013 ↗
23. Fatigue of AlSi10mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM)10.1016/j.msea.2017.08.027 ↗
24. Additive manufactured AlSi10mg samples using selective laser melting (SLM): microstructure, high cycle fatigue, and fracture behavior10.1016/j.matdes.2011.07.067 ↗
25. Oxides, porosity and fatigue performance of AlSi10mg parts produced by selective laser melting10.1016/j.ijfatigue.2016.06.002 ↗
26. Processing AlSi10mg by selective laser melting: parameter optimisation and material characterisation10.1179/1743284714Y.0000000702 ↗
27. Selective laser melting of AlSi10Mg alloy: process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
28. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10mg powder10.1016/j.actamat.2012.11.052 ↗
29. Microstructure and strength of selectively laser melted AlSi10Mg10.1016/j.actamat.2016.07.012 ↗
30. Rapid solidification: selective laser melting of AlSi10Mg10.1007/s11837-015-1763-3 ↗
31. Electrical resistivity of additively manufactured AlSi10mg for use in electric motors10.1016/j.addma.2018.03.027 ↗
32. Enhancement of electrical conductivity and corrosion resistance by silver shell-copper core coating of additively manufactured AlSi10mg alloy10.1016/j.surfcoat.2020.126426 ↗
33. Gold plating of AlSi10mg parts produced by a laser powder-bed fusion additive manufacturing technique10.1007/s40964-020-00134-6 ↗
34. Gold, silver, and electrum electroless plating on additively manufactured laser powder-bed fusion AlSi10mg parts: a review10.3390/coatings11040422 ↗
35. Gold–silver electroless plating on laser powder-bed fusion additively printed AlSi10mg parts10.3390/met10050557 ↗
36. Effect of microstructure and porosity of AlSi10Mg alloy produced by selective laser melting on the corrosion properties of plasma electrolytic oxidation coatings10.1016/j.surfcoat.2020.126477 ↗
37. Enhancing the corrosion properties of additively manufactured AlSi10mg using friction stir processing10.1016/j.corsci.2020.109073 ↗
38. Diffusion mechanism in the gold-copper system10.1007/s10854-012-0729-2 ↗
39. Mechanical behavior of additive manufactured, powder-bed laser-fused materials10.1016/j.msea.2015.10.068 ↗
40. Reducing porosity in AlSi10Mg parts processed by selective laser melting
41. Formation and reduction of hydrogen porosity during selective laser melting of AlSi10Mg10.1016/j.jmatprotec.2015.02.013 ↗
42. 3D printing of high-strength aluminium alloys10.1038/nature23894 ↗
43. Porosity formation mechanisms and fatigue response in Al-Si-Mg alloys made by selective laser melting10.1016/j.msea.2017.11.078 ↗
44. The effect of ultrasound on the gold plating of silica nanoparticles for use in composite solders10.1016/j.ultsonch.2010.04.010 ↗
45. Influences of trace additions of strontium and phosphorus on electrical resistivity and viscosity of liquid Al-Si alloys
46. Corrosion behaviour of electrodeposited nanocrystalline co and co/ZrO2nanocomposite coatings10.1179/1743294414Y.0000000355 ↗
47. Direct observations of microstructure-resolved corrosion initiation in AA7075-T651 at the nanoscale using vertical scanning interferometry (VSI)10.1016/j.matchar.2020.110166 ↗
48. A comparative study of corrosion behavior of an additively manufactured Al-6061 RAM2 with extruded Al-6061 T610.1016/j.corsci.2020.108838 ↗
49. A new approach to the chemistry of gold10.1007/BF03215041 ↗
50. Gold's future role in fuel cell systems10.1016/S0378-7753(03)00074-0 ↗
51. Effect of zincation/sonication on electroplated gold deposited on aluminum substrate10.1007/s11665-010-9715-0 ↗
52. The influence of the sandblasting as a surface mechanical attrition treatment on the electrochemical behavior of carbon steel in different pH solutions10.1016/j.surfcoat.2018.08.013 ↗
53. Effect of grain size on corrosion: a review10.5006/1.3462912 ↗
54. Revealing the relationship between grain size and corrosion rate of metals10.1016/j.scriptamat.2010.08.035 ↗
55. Structure and thermodynamic properties of nanocrystalline metals10.1103/PhysRevB.45.635 ↗
56. Electrochemical behavior of a magnesium ZK60 alloy processed by high-pressure torsion10.1016/j.corsci.2019.04.006 ↗
57. An investigation on the role of crystallographic texture on anisotropic electrochemical behavior of a commercially pure nickel manufactured by laser powder bed fusion (L-PBF) additive manufacturing10.1016/j.electacta.2020.136694 ↗
58. Characterization of frequency dispersion in the impedance response of a distributed model from the mathematical properties of the distribution function of relaxation times10.1016/j.electacta.2015.08.140 ↗
59. Simulated impedance of diffusion in porous media10.1016/j.electacta.2017.07.152 ↗
60. Relationship between the origin of constant-phase element behavior in electrochemical impedance spectroscopy and electrode surface structure10.1021/jp512063f ↗
61. Relationship between constant-phase element (CPE) parameters and physical properties of films with a distributed resistivity10.1016/j.electacta.2016.12.087 ↗
62. Contribution of surface distributions to constant-phase-element (CPE) behavior: 3. adsorbed intermediates10.1016/j.electacta.2017.08.081 ↗
63. Exfoliation corrosion of aluminium alloys examined by electrode impedance10.1016/0013-4686(96)00170-3 ↗
64. Impedance spectroscopy analysis of structural defects in sputtered ZnO films10.1002/celc.202000087 ↗
65. Estimation of the pore structure of porous electrodes from impedance measurements10.1016/0013-4686(76)85147-X ↗
66. Surface characterization and corrosion behavior of a novel gold-imitation copper alloy with high tarnish resistance in salt spray environment10.1016/j.corsci.2013.05.026 ↗
67. Corrosion of 304 stainless steel in carbonates melt– a state of enhanced dissolution of corrosion products10.1016/j.corsci.2020.108535 ↗
68. Impedance spectroscopy at interfaces of metals and aqueous solutions — surface roughness, CPE and related issues10.1016/j.ssi.2004.06.023 ↗