Effect of the initial substrate temperature on heat transfer and related phenomena in austenitic stainless steel parts fabricated by additive manufacturing using direct energy deposition
Source abstract
Abstract
In this study, the effect of preheating a AISI 304 steel substrate to 300 °C, compared to a room-temperature substrate, just before direct energy deposition (DED) additive manufacturing of a AISI 316 L steel deposit in terms of absorptivity of the laser beam, heat transfer, microstructure, hardness and residual stress. The samples were thermally isolated using an alumina cup. Using direct energy deposition for 20 and 40 layers of steel, it was found absorptivities of 18% and 16%, respectively, in room temperature (RT) experiments. At high temperatures (HT, 300 °C) the net absorptivity is almost zero because of convective and radiative cooling. The estimated heat transfer coefficients are approximately 1.0 and 0.4 Wm−2K−1, for RT and HT respectively. The microstructure and hardness obtained under each condition (RT or HT) for 20 or 40 layers, were quite similar. The microstructures were composed of austenitic grains with a Vickers hardness values ranging from 170 to 220 HV. The measured residual stresses were quite low for additive manufacturing of austenitic stainless steel, ranging from 11 to −22 MPa for RT and from 37 to −17 MPa for HT.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Impact of metal additive manufacturing parameters on the powder bed fusion and direct energy deposition processes: a comprehensive review10.1007/s40964-021-00180-8 ↗
2. Defect-free laser powder bed fusion of Ti–48Al–2Cr–2Nb with a high temperature inductive preheating system
3. Numerical simulation of heat transfer and fluid flow in coaxial laser cladding process for direct metal deposition10.1063/1.2209807 ↗
4. Evaluation of a temperature measurement method developed for laser metal deposition10.1080/13621718.2016.1169363 ↗
5. Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing10.1007/s00170-020-04972-0 ↗
6. Stainless steel: heat treatment
7. Steen · 2010
8. Measurement of the optical constants of Al above the melting point at λ= 10.6 μm10.1063/1.333760 ↗
9. In-situ technique for measuring the absorption during laser surface remelting10.1007/BF02672536 ↗
10. Heat transfer and fluid flow in additive manufacturing10.2351/1.4817788 ↗
11. An experimental investigation into additive manufacturing-induced residual stresses in 316L stainless steel10.1007/s11661-014-2549-x ↗
12. A review on metallurgical aspects of laser additive manufacturing (LAM): stainless steels, nickel superalloys, and titanium alloys
13. Solidification microstructure and residual stress correlations in direct energy deposited type 316L stainless steel10.1016/j.matdes.2021.109782 ↗
14. Review on residual stresses in metal additive manufacturing: formation mechanisms, parameter dependencies, prediction and control approaches10.1016/j.jmrt.2022.02.054 ↗
15. Thermomechanical and isothermal fatigue behavior of 347 and 316L austenitic stainless tube and pipe steels10.1016/j.ijfatigue.2010.11.005 ↗
16. Technical Data Sheet LPW 316L Stainless Steel 1.4404. Available in https://www.camodels.co.uk/media/1315/metal-am-stainless-steel-316-datasheet-ca-models.pdf(accessed 25/03/2022).
17. Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel
18. Prevey PS X-ray diffraction residual stress techniques
19. Schwartz · 2013
20. Overview of laser absorptivity measurement techniques for material processing10.1007/s40516-018-0075-1 ↗
21. Heat in history Isaac Newton and heat transfer10.1080/01457639808939932 ↗
22. Josef stefan and his contributions to heat transfer
23. Newton's law of cooling—a critical assessment10.1119/1.16309 ↗
24. 2009
25. Emissitivity of Common Materials, Available in https://www.omega.co.uk/literature/transactions/volume1/emissivitya.html (accessed 25/03/2022).
26. Valencia · 2013
27. Forced convection on grey cast iron plate-fins: prediction of the heat transfer coefficient10.1016/j.icheatmasstransfer.2016.11.007 ↗
28. Inverse problem-coupled heat transfer model for steel continuous casting10.1016/j.jmatprotec.2013.07.017 ↗
29. Effects of phase transition temperature and preheating on residual stress in multi-pass & multi-layer laser metal deposition10.1016/j.jallcom.2019.04.104 ↗
30. Numerical model of heat transfer during laser powder bed fusion of 316L stainless steel10.1007/s00170-021-08352-0 ↗
31. Powder catchment in laser metal deposition10.2351/1.5096130 ↗
32. Characterization of stainless steel parts by laser metal deposition shaping10.1016/j.matdes.2013.09.006 ↗
33. Quantitative multiscale correlative microstructure analysis of additive manufacturing of stainless steel 316L processed by selective laser melting10.1016/j.matchar.2019.110074 ↗
34. An investigation on the effect of deposition pattern on the microstructure, mechanical properties and residual stress of 316L produced by Directed Energy Deposition10.1016/j.msea.2020.139179 ↗
35. The solidification sequence in an 18-8 stainless steel, investigated by directional solidification10.1007/BF02652872 ↗
36. Microstructural development and solidification cracking susceptibility of austenitic stainless steel welds10.1179/imr.1991.36.1.16 ↗
37. Coalescence of equiaxed grains during solidification10.1088/0965-0393/12/3/009 ↗
38. Origin of dislocation structures in an additively manufactured austenitic stainless steel 316L10.1016/j.actamat.2020.07.063 ↗
39. Solidification mechanism of austenitic stainless steels solidified with primary ferrite10.1016/j.actamat.2016.11.030 ↗
40. Integration of processing and microstructure models for non-equilibrium solidification in additive manufacturing10.3390/met11040570 ↗
41. Effect of heat treatment on bonding interface in explosive welded copper/stainless steel10.1016/j.matdes.2012.09.037 ↗
42. Influence of severe plastic deformation on structure and phase composition of carbon steel10.1016/0965-9773(94)90075-2 ↗
43. Thermal stability and microstructural evolution of additively manufactured 316L stainless steel by laser powder bed fusion at 500–800°C
44. Hardesty · 1981