Cr-rich structure evolution and enhanced mechanical properties of CoCrFeNi high entropy alloys by mechanical alloying
Source abstract
Abstract
Mechanically-alloyed CoCrFeNi high entropy alloys (MA-HEAs) show better mechanical properties than as-cast HEAs. However, the limited amount of powder milled in one-milling cycle creates a challenge in larger-scale applications. The low ball-to-powder ratio (BPR) milling used to increase powder yield resulted in the formation of Cr-rich second phases in the face-centered cubic matrix. To overcome the above issues, in this work, with a low BPR of 5:1, four different processes were analyzed: quicker milling intervals, higher milling speed, and the pre-alloying of Cr and Ni. All parameters mentioned before were used and tested together in the fourth sample. Samples were consolidated by spark plasma sintering technique. Microstructural characterization was made on a Scanning Electron Microscope equipped with EDS and EBSD detectors and a Transmission Electron Microscope. X-ray diffraction was employed to develop the structural evolution of powders sintered and annealed samples. The global hardness was measured using microhardness tests, while the nanohardness tests helped us correlate the evolution of secondary phases with their mechanical properties. The results show that pre-alloying elements with the lowest diffusion coefficient before the main milling process might be an attractive strategy to improve productivity and optimize microstructure without limiting the efficiency of low BPR MA-HEAs. The results described below demonstrate the promising perspective for the implementation of powder metallurgy techniques in a mass scale production as low BPR is essential for numerous applications like aerospace industry, car engines and medicine, where improved productivity of powder mixing is mandatory.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. Mechanically alloyed high entropy alloys: existing challenges and opportunities10.1016/j.jmrt.2022.01.141 ↗
2. Synthesis and processing10.1016/B978-0-12-800251-3.00005-5 ↗
3. Development of cemented carbides with CoxFeNiCrCu high-entropy alloyed binder prepared by spark plasma sintering10.1016/j.ijrmhm.2021.105751 ↗
4. Effects of Y2O3/Ti/Zr addition on microstructure and hardness of ODS-CoCrFeNi HEAs produced by mechanical alloying and spark plasma sintering10.1016/j.jallcom.2020.157940 ↗
5. Enhanced wearing resistance of carbide reinforced FeCoNiCrMn high entropy alloy prepared by mechanical alloying and spark plasma sintering
6. Strengthening of Al0.3CoCrFeMnNi-based ODS high entropy alloys with incremental changes in the concentration of Y2O310.1016/j.scriptamat.2018.12.021 ↗
7. Microstructures and mechanical properties of oxide dispersion strengthened CoCrFeNi high-entropy alloy produced by mechanical alloying and spark plasma sintering10.1016/j.intermet.2020.106819 ↗
8. Microstructures and properties of high-entropy alloys10.1016/j.pmatsci.2013.10.001 ↗
9. Mechanically alloyed (FeCoNi)75Cu25−xSix high entropy alloys: phase evaluation and magnetic properties10.1016/j.jallcom.2023.170030 ↗
10. The effect of processing parameters and heat-treatment on the microstructure and mechanical properties of PM CoCrFeMnNiTi0.1 high-entropy alloy10.1016/j.matchemphys.2020.123722 ↗
11. Effects of milling time, sintering temperature, Al content on the chemical nature, microhardness and microstructure of mechanochemically synthesized FeCoNiCrMn high entropy alloy10.1016/j.jallcom.2018.03.358 ↗
12. Effects of milling process parameters and PCAs on the synthesis of Al0.8Co0.5Cr1.5CuFeNi high entropy alloy powder by mechanical alloying10.1016/j.matdes.2022.110637 ↗
13. Influence of process control agent and Al concentration on synthesis and phase stability of a mechanically alloyed AlxCoCrFeMnNi high-entropy alloy10.1016/j.jallcom.2021.160770 ↗
14. Alloying, thermal stability and strengthening in spark plasma sintered AlxCoCrCuFeNi high entropy alloys10.1016/j.jallcom.2013.08.176 ↗
15. Microstructure and mechanical properties of a CoCrFeMnNi high entropy alloy processed by milling and spark plasma sintering10.1016/j.jallcom.2018.11.181 ↗
16. Grain growth kinetics in CoCrFeNi and CoCrFeMnNi high entropy alloys processed by spark plasma sintering10.1016/j.jallcom.2019.03.341 ↗
17. Alloy design strategies and future trends in high-entropy alloys10.1007/s11837-013-0761-6 ↗
18. Spark plasma sintering as an approach to manufacture bulk materials: Feasibility and cost savings10.1007/s11837-014-1202-x ↗
19. Cavaliere · 2019
20. A critical review of high entropy alloys and related concepts10.1016/j.actamat.2016.08.081 ↗
21. Microstructure and mechanical properties of mechanically-alloyed CoCrFeNi high-entropy alloys using low ball-to-powder ratio10.1016/j.jallcom.2022.168196 ↗
22. Properties of a high-strength ultrafine-grained CoCrFeNiMn high-entropy alloy prepared by short-term mechanical alloying and spark plasma sintering10.1016/j.msea.2018.08.014 ↗
23. Effect of heat treatment on microstructure and mechanical properties of spark plasma sintered AlCoCrFeNiTi0.5 high entropy alloy10.1016/j.matlet.2016.03.077 ↗
24. Synthesis and thermodynamic analysis of nanostructured CuNiCoZnAl high entropy alloy produced by mechanical alloying10.1016/j.jallcom.2016.05.274 ↗
25. Study of (Ni,Cr) pre-milling for synthesis of CoFe(NiCr)Mn high entropy alloy by mechanical alloying10.1016/j.msea.2021.140810 ↗
26. Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation10.1016/j.matchar.2022.111833 ↗
27. High entropy alloys obtained by field assisted powder metallurgy route: SPS and microwave heating10.1016/j.matchemphys.2017.06.065 ↗
28. The Powder Diffraction File: a quality materials characterization database10.1017/S0885715619000812 ↗
29. Line profiles of neutron powder-diffraction peaks for structure refinement10.1107/S0365110X67000234 ↗
30. A profile refinement method for nuclear and magnetic structures10.1107/S0021889869006558 ↗
31. X-ray diffraction line broadening: modeling and applications to high-Tc superconductors10.6028/jres.098.026 ↗
32. Phenomenological model of anisotropic peak broadening in powder diffraction10.1107/S0021889898006001 ↗
33. Understanding anisotropic microstrain broadening in Rietveld refinement10.1524/zkri.2011.1413 ↗
34. Short-range order and its impact on the CrCoNi medium-entropy alloy10.1038/s41586-020-2275-z ↗
35. Phase evolution and densification behavior of nanocrystalline multicomponent high entropy alloys during spark plasma sintering10.1007/s11837-013-0759-0 ↗
36. Warren · 1969
37. Surface oxidation mechanism of CoCrFeNi high entropy alloy10.1016/j.susc.2022.122124 ↗
38. Structure of some CoCrFeNi and CoCrFeNiPd multicomponent HEA alloys by diffraction techniques10.1016/j.jallcom.2016.04.248 ↗
39. Effect of SiC nano-particles on microstructure and mechanical properties of the CoCrFeMnNi high entropy alloy10.1016/j.jallcom.2017.02.274 ↗
40. High versus low energy ion irradiation impact on functional properties of PLD-grown alumina coatings10.1016/j.nimb.2023.03.027 ↗
41. Microstructure and mechanical properties of Ni1,5Co1,5CrFeTi0,5 high entropy alloy fabricated by mechanical alloying and spark plasma sintering10.1016/j.matdes.2017.01.036 ↗
42. Alloying behavior in multi-component AlCoCrCuFe and NiCoCrCuFe high entropy alloys10.1016/j.msea.2011.11.044 ↗
43. High-entropy FeNiCoCr alloys with improved mechanical and tribological properties by tailoring composition and controlling oxidation10.1016/j.jmst.2020.12.042 ↗
44. Al0.3CrxFeCoNi high-entropy alloys with high corrosion resistance and good mechanical properties10.1016/j.jallcom.2020.158436 ↗
45. The effect of temperature on the evolution of eutectic carbides and M7C3 → M23C6carbides reaction in the rapidly solidified Fe-Cr-C alloy10.1016/j.jallcom.2016.12.252 ↗
46. Thermal stability of nanostructured NiCrC coating prepared by HVAF spraying of cryomilled powders10.1016/S1001-0521(08)60155-2 ↗
47. The precipitation and transformation of secondary carbides in a high chromium cast iron10.1016/j.matchar.2005.10.002 ↗
48. Simultaneous synthesis and consolidation of chromium carbides (Cr3C2, Cr7C3 and Cr23C6) by pulsed electric-current pressure sintering10.1016/j.msea.2005.02.062 ↗
49. Developing harmonic structure in CoCrFeMnNi high entropy alloy to enhance mechanical properties via powder metallurgy approach10.1016/j.jmrt.2022.01.098 ↗
50. Effect of Ti and C additions on the microstructure and mechanical properties of the FeCoCrNiMn high-entropy alloy10.1016/j.msea.2018.02.040 ↗
51. Strengthening the mechanical properties and wear resistance of CoCrFeMnNi high entropy alloy fabricated by powder metallurgy10.1016/j.apt.2022.103519 ↗
52. Carbon-alloyed Fe35Mn10Cr20Ni35 high entropy alloy synthesized by mechanical alloying plus spark plasma sintering10.1016/j.jallcom.2020.157851 ↗